Yun Jiang
Yun Jiang has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
Bo. Yuan. Liu
National University of Defense Technology,College of Electronic Science and Technology,Changsha,Hunan,China,410073
1 shared publicationBoyuan Liu
Department of Electronic Science and Engineering, National University of Defense Technology, Changsha, China
1 shared publicationChang Zhu
Natl Univ Def Technol, Coll Elect Sci & Engn, Changsha 410073, Peoples R China
1 shared publicationChao Wang
Department of Electronic Science and Engineering, National University of Defense Technology, Changsha, China
1 shared publication- Chao Wang
Research Center of Intelligent Communication Engineering, School of Electronics and Communication Engineering, Guangzhou University, Guangzhou, China
1 shared publication Jing Huang
Natl Univ Def Technol, Coll Elect Sci & Engn, Changsha 410073, Peoples R China
1 shared publication
Latest Publications
- Open Access
- 31 December 2024
- Published by River Publishers in Applied Computational Electromagnetics Society Journal (ACES)
- p. 1066-1072
An All-metal Antipodal Vivaldi Antenna Design for High-power Microwave Application
In this paper, the evolutionary process, fabrication and measurement of an all-metal antipodal Vivaldi antenna (AMAVA) design are presented for the high-power microwave (HPM) application. Derived from the substrate-loaded antipodal Vivaldi antenna, the proposed antenna is made all metallic to enhance its power handling capacity (PHC). Considering the further improvement of the radiation performance and antenna fixing, rectangular slots and tuning stubs with exponential corner cuts are employed in antenna design. In the air condition, the PHC values of the final proposed antenna are over 8000 W in its operating band. The proposed AMAVA is fabricated and measured in a microwave anechoic chamber. According to the measured results, the −10 dB impedance bandwidth covers 8.3-10.66 GHz, and its deepest resonance reaches −29.7 dB at 9.75 GHz. The measured radiation pattern values are in agreement with simulation values, and its peak gain values at 9.3 GHz, 9.8 GHz and 10.3 GHz are 4.54 dBi, 5.68 dBi and 5.71 dBi, respectively. A PHC experiment is conducted, which verifies the AMAVA is qualified for 8000 W-level PHC.
- 31 December 2024
- Published by River Publishers in Applied Computational Electromagnetics Society Journal (ACES)
- p. 1066-1072
Open AccessAn All-metal Antipodal Vivaldi Antenna Design for High-power Microwave Application
In this paper, the evolutionary process, fabrication and measurement of an all-metal antipodal Vivaldi antenna (AMAVA) design are presented for the high-power microwave (HPM) application. Derived from the substrate-loaded antipodal Vivaldi antenna, the proposed antenna is made all metallic to enhance its power handling capacity (PHC). Considering the further improvement of the radiation performance and antenna fixing, rectangular slots and tuning stubs with exponential corner cuts are employed in antenna design. In the air condition, the PHC values of the final proposed antenna are over 8000 W in its operating band. The proposed AMAVA is fabricated and measured in a microwave anechoic chamber. According to the measured results, the −10 dB impedance bandwidth covers 8.3-10.66 GHz, and its deepest resonance reaches −29.7 dB at 9.75 GHz. The measured radiation pattern values are in agreement with simulation values, and its peak gain values at 9.3 GHz, 9.8 GHz and 10.3 GHz are 4.54 dBi, 5.68 dBi and 5.71 dBi, respectively. A PHC experiment is conducted, which verifies the AMAVA is qualified for 8000 W-level PHC.
- 28 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. ume1, 1-3
Miniaturization Design of X-Band Filter with High Suppression Based on MEMS Chip Technology
Large scale integrated circuit (IC), where the down-conversion circuit usually acts as the main chain of receiving channel, requires appropriate miniaturized filter as one of the most important units to effectively suppress mirror frequency caused by front-end mixing process to some extent. MEMS (Micro Electro Mechanical System) chip technology is introduced for its greater performance and reliability in lower power consumption and a smaller volume. In this paper, starting with the analysis of the structure and characteristics of the filter chip, the MEMS filter’s advantages over the traditional structure and structural features are described, and a X-band MEMS filter is designed through calculation, modeling and simulation in sequence, to furtherly contribute to mixing channel with high suppression on unwanted signal frequency. The MEMS filter satisfies demands of miniaturization and integration, conforming to the chip technology development, which is suitable for popularity in practical applications.
- 28 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. ume1, 1-3
Miniaturization Design of X-Band Filter with High Suppression Based on MEMS Chip Technology
Large scale integrated circuit (IC), where the down-conversion circuit usually acts as the main chain of receiving channel, requires appropriate miniaturized filter as one of the most important units to effectively suppress mirror frequency caused by front-end mixing process to some extent. MEMS (Micro Electro Mechanical System) chip technology is introduced for its greater performance and reliability in lower power consumption and a smaller volume. In this paper, starting with the analysis of the structure and characteristics of the filter chip, the MEMS filter’s advantages over the traditional structure and structural features are described, and a X-band MEMS filter is designed through calculation, modeling and simulation in sequence, to furtherly contribute to mixing channel with high suppression on unwanted signal frequency. The MEMS filter satisfies demands of miniaturization and integration, conforming to the chip technology development, which is suitable for popularity in practical applications.
- 15 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 32 (4) , 289-292
W-Band E-Plane Waveguide Filter Using Compact Beeline Resonator
This letter presents a novel but very simple W-band E-plane waveguide bandpass filter (BPF) using just one compact beeline resonator (CBR), which leads to multiple transmission zeros (TZs). The proposed filter with low insertion loss (IL) and high selectivity is only 3.21 mm in length of the E-plane substrate. For further demonstration, a filter example with center frequency at $f_{0} =$ 88.55 GHz is implemented with generation of three TZs for theoretically calculated certification. Moreover, the measured minimum IL is only 1.15 dB. Good agreement between simulations and measurements validates the design method.- 15 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 32 (4) , 289-292
W-Band E-Plane Waveguide Filter Using Compact Beeline Resonator
This letter presents a novel but very simple W-band E-plane waveguide bandpass filter (BPF) using just one compact beeline resonator (CBR), which leads to multiple transmission zeros (TZs). The proposed filter with low insertion loss (IL) and high selectivity is only 3.21 mm in length of the E-plane substrate. For further demonstration, a filter example with center frequency at $f_{0} =$ 88.55 GHz is implemented with generation of three TZs for theoretically calculated certification. Moreover, the measured minimum IL is only 1.15 dB. Good agreement between simulations and measurements validates the design method.- 19 August 2021
- Published by River Publishers in Applied Computational Electromagnetics Society Journal (ACES)
- Vol. 36 (7) , 872-878
A Wideband and Wide Scanning Tightly Coupled Dipole Array with Meta-Surface Wide-Angle Impedance Matching
A low profile ultra-wideband tightly coupled dipole array is studied. The antenna elements are fed by Marchand baluns of small size and low cost. A metasurface based wide-angle impedance matching (MSWAIM) layer is introduced to replace the traditional dielectric WAIM, improving the beam scan performance and reducing the antenna profile. The simulation shows that the proposed antenna array can operate over 2.4-12.4 GHz, approximately 5:1 bandwidth with maximum scanning angle of 50o for both E plane and 45o for H plane. The antenna profile above the ground is only 0.578λH at the highest operating frequency. This antenna array can find its application in the forthcoming massive MIMO beamforming systems for 5G.
- 19 August 2021
- Published by River Publishers in Applied Computational Electromagnetics Society Journal (ACES)
- Vol. 36 (7) , 872-878
A Wideband and Wide Scanning Tightly Coupled Dipole Array with Meta-Surface Wide-Angle Impedance Matching
A low profile ultra-wideband tightly coupled dipole array is studied. The antenna elements are fed by Marchand baluns of small size and low cost. A metasurface based wide-angle impedance matching (MSWAIM) layer is introduced to replace the traditional dielectric WAIM, improving the beam scan performance and reducing the antenna profile. The simulation shows that the proposed antenna array can operate over 2.4-12.4 GHz, approximately 5:1 bandwidth with maximum scanning angle of 50o for both E plane and 45o for H plane. The antenna profile above the ground is only 0.578λH at the highest operating frequency. This antenna array can find its application in the forthcoming massive MIMO beamforming systems for 5G.