Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Sangho Kim has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A Directional Spectral Database for UAM Noise Prediction: Construction and Reconstruction Assessment

    by Sea Ryu, Junyeop Kwon, Dahui Choi, Hamin Kim, Sangho Kim

    Directional spectra preserve source information for trajectory-based noise models, but low reconstruction error does not establish physical source accuracy. We present a JSON database for eight X500 multicopter states, each with 266 receiver directions at approximately 1 m. Our comparison uses 25 complete, one-third-octave bands from 50 Hz to 12.5 kHz. Repeated grouped directional holdouts yield mean-square-pressure (MSP) OASPL MAE of 0.3–0.8 dB, P95 up to 3.3 dB, maximum OASPL error of 9.1 dB, and maximum individual-band error of 26.8 dB. Expanding the RBF candidates, selecting parameters on training data, and applying numerical guards reduces MAE to 0.09–0.44 dB. Full-density transfer to 960 independently located, ground-directed receivers from the same climb-2 CFD source gives MSP OASPL MAE/P95/maximum of 1.11/2.91/3.98 dB and restricted A-weighted MAE of 0.57 dB. MSP remains the default for ground-directed transfer. Withheld interior speed states give OASPL MAE of 0.42–1.18 dB. Outdoor hover observations at altitudes of 10 and 20 m exceed propagated database levels by mean differences of 15.3–19.0 dB across recorder sequences. This discrepancy does not establish absolute community-noise accuracy. Temporal record sensitivity, coordinate correction, triangle quality, integrated-field consistency, and measured query costs define the supported reconstruction use and remaining source/propagation validation requirements.

  • Open Access

    Terrain-Aware Noise Mapping Framework for Low-Altitude Aircraft Operations Using Terrain-Based Receiver Grids

    by Shiho Lee, Dahui Choi, Sangho Kim

    Low-altitude UAV/UAM noise is affected by flight trajectory, source condition, terrain elevation, and receiver location, which makes a spatially integrated calculation procedure necessary for noise mapping. In this work, these elements are connected within a terrain-aware computational framework. Time-based UAV flight data are transformed into a common projected coordinate system and combined with operating-state-dependent source levels and terrain-based receiver grids. Sound propagation is then calculated for each source–receiver pair over time, and the resulting SPL histories are integrated into SEL and

  • Open Access

    Motion Estimation and Hand Gesture Recognition-Based Human–UAV Interaction Approach in Real Time

    by Minjeong Yoo, Yuseung Na, Hamin Song, Gamin Kim, Junseong Yun, Sangho Kim, Changjoo Moon, Kichun Jo

    As an alternative to traditional remote controller, research on vision-based hand gesture recognition is being actively conducted in the field of interaction between human and unmanned aerial vehicle (UAV). However, vision-based gesture system has a challenging problem in recognizing the motion of dynamic gesture because it is difficult to estimate the pose of multi-dimensional hand gestures in 2D images. This leads to complex algorithms, including tracking in addition to detection, to recognize dynamic gestures, but they are not suitable for human–UAV interaction (HUI) systems that require safe design with high real-time performance. Therefore, in this paper, we propose a hybrid hand gesture system that combines an inertial measurement unit (IMU)-based motion capture system and a vision-based gesture system to increase real-time performance. First, IMU-based commands and vision-based commands are divided according to whether drone operation commands are continuously input. Second, IMU-based control commands are intuitively mapped to allow the UAV to move in the same direction by utilizing estimated orientation sensed by a thumb-mounted micro-IMU, and vision-based control commands are mapped with hand’s appearance through real-time object detection. The proposed system is verified in a simulation environment through efficiency evaluation with dynamic gestures of the existing vision-based system in addition to usability comparison with traditional joystick controller conducted for applicants with no experience in manipulation. As a result, it proves that it is a safer and more intuitive HUI design with a 0.089 ms processing speed and average lap time that takes about 19 s less than the joystick controller. In other words, it shows that it is viable as an alternative to existing HUI.


  • Open Access

    Estimation and Separation of Longitudinal Dynamic Stability Derivatives with Forced Oscillation Method Using Computational Fluid Dynamics

    by Nadhie Juliawan, Hyoung-Seog Chung, Jae-Woo Lee, Sangho Kim

    This paper focuses on estimating dynamic stability derivatives using a computational fluid dynamics (CFD)-based force oscillation method, and on separating the coupled dynamic derivatives terms obtained from the method. A transient RANS solver is used to calculate the time history of aerodynamic moments for a test model oscillating about the center of gravity, from which the coupled dynamic derivatives are estimated. The separation of the coupled derivatives term is carried out by simulating simple harmonic oscillation motions such as plunging motion and flapping motion which can isolate the pitching moment due to AOA rate (Cmα˙) and the pitching moment due to pitch rate (Cmq), respectively. The periodic motions are implemented using a CFD dynamic mesh technique with user-defined function (UDF). For the validation test, steady and unsteady simulations are performed on the Army-Navy Finner Missile model. The static aerodynamic moments and pressure distribution, as well as the coupled dynamic derivative results from the pitching oscillation mode, show good agreement with the previously published wind tunnel tests and CFD analysis data. In order to separate the coupled derivative terms, two additional harmonic oscillation modes of plunging and flapping motions are tested with the angle of attack variations from 0 to 85 degrees at a supersonic speed to provide real insight on the missile maneuverability. The cross-validation study between the three oscillation modes indicates the summation of the individual plunging and flapping results becoming nearly identical to the coupled derivative results from the pitching motion, which implies the entire set of coupled and separated dynamic derivative terms can be effectively estimated with only two out of three modes. The advantages and disadvantages of each method are discussed to determine the efficient approach of estimating the dynamic stability derivatives using the forced oscillation method.


  • Design-airworthiness integration method for general aviation aircraft during early development stage

    by Maxim Tyan, Jungwon Yoon, Nhu Van Nguyen, Jae-Woo Lee, Sangho Kim

    Purpose: Major changes of an aircraft configuration are conducted during the early design stage. It is important to include the airworthiness regulations at this stage while there is extensive freedom for designing. The purpose of this paper is to introduce an efficient design framework that integrates airworthiness guidelines and documentation at the early design stage. Design/methodology/approach: A new design and optimization process is proposed that logically includes the airworthiness regulations as design parameters and constraints by constructing a certification database. The design framework comprises requirements analysis, preliminary sizing, conceptual design synthesis and loads analysis. A design certification relation table (DCRT) describes the legal regulations in terms of parameters and values suitable for use in design optimization. Findings: The developed framework has been validated and demonstrated for the design of a Federal Aviation Regulations (FAR) 23 four-seater small aircraft. The validation results show an acceptable level of accuracy to be applied during the early design stage. The total mass minimization problem has been successfully solved while satisfying all the design requirements and certification constraints specified in the DCRT. Moreover, successful compliance with FAR 23 subpart C is demonstrated. The proposed method is a useful tool for design optimization and compliance verifications during the early stages of aircraft development. Practical implications: The new certification database proposed in this research makes it simpler for engineers to access a large amount of legal documentation related to airworthiness regulations and provides a link between the regulation text and actual design parameters and their bounds. Originality/value: The proposed design optimization framework integrates the certification database that is built of several types of legal documents such as regulations, advisory circulars and standards. The Engineering Requirements and Guide summarizes all the documents and design requirements into a single document. The DCRT is created as a summary table that indicates the design parameters affected by a given regulation(s), the design stage at which the parameter can be evaluated and its value bounds. The introduction of the certification database into the design optimization framework significantly reduces the engineer’s load related for airworthiness regulations.


  • Investigations on stability and control characteristics of a CS-VLA certified aircraft using wind tunnel test data

    by Nhu Van Nguyen, Maxim Tyan, Jae-Woo Lee, Sangho Kim

    The stability and control characteristics using a wind tunnel test data process are proposed and developed to investigate the stability and control characteristics of a CS-VLA certified aircraft and to comply with the CS-VLA subpart B at the preliminary design review (PDR) and critical design review (CDR) stage. The aerodynamic characteristics of a 20% scale model are provided and investigated with clean, rudder, aileron, elevator, and winglet effects. The Mach and Reynolds correction methods are proposed to correct the aerodynamics of the scale model for stability and control analysis to obtain more reliable and accurate results of the full-scale model. The aerodynamic inputs and moment of inertia (MOI) comparison between the PDR and CDR stage show good agreement in the trends of stability and control derivatives. The CDR analysis results with the corrected wind tunnel test data and accurate MOI are investigated with respect to the longitudinal and lateral stability, control, and handling qualities to comply with the CS-VLA 173, CS-VLA 177, and CS-VLA 181 for finalizing the configuration in the CDR stage.


  • Efficient stall compliance prediction method for trimmed very light aircraft with high-lift devices

    by Nhu Van Nguyen, Daeyeon Lee, Maxim Tyan, Jae-Woo Lee, Sangho Kim

    An efficient stall compliance prediction method using quick configuration generation, adapted mesh, high fidelity analysis, and wind tunnel test data for trimmed very light aircraft is proposed. The three-dimensional Navier–Stokes equations are used to determine the characteristics of the flow field around the aircraft, and the k-ω shear stress transport model is used to interpret the turbulent flow as a solver in the high fidelity analysis. The calibrated mesh and model are developed by comparing the results with the wind tunnel test and adjusting the adapted mesh to match the wind tunnel data. The calibrated mesh and model are applied to conduct the full-scale very light aircraft analysis for the clean and full flap extended flight conditions to comply with the CS-VLA stall regulations. It is recommended that the flap area be increased in the trimmed full flap extended condition. The proposed method demonstrates the feasibility and effectiveness of very light aircraft VLA stall compliance prediction in reducing the development cost and time with small configuration changes at the preliminary very light aircraft design stage.