Sumin Pyo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Sumin Pyo has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Young-Kwon Park
University of Seoul
4 shared publications - Young-Min Kim
Department of Energy System Engineering, Daegu University, Gyeongsan, 38453, Republic of Korea
3 shared publications Gwang Hoon Rhee
Department of Mechanical and Information Engineering, University of Seoul, Seoul 02504, Republic of Korea
2 shared publications- Byong-Hun Jeon
Department of Earth Resources and Environmental Engineering Hanyang University Seoul Republic of Korea
1 shared publication - Gi-Jeong Woo
Department of Environmental Engineering, Daegu University, Gyeongsan 38453, Korea
1 shared publication - Gwang Hoon Rhee
Department of Mechanical and Information Engineering, University of Seoul, Seoul 02504, Korea
1 shared publication
Latest Publications
- 17 June 2022
- Published by Elsevier in Bioresource Technology
- Vol. 359, 127500
MgO-modified activated biochar for biojet fuels from pyrolysis of sawdust on a simple tandem micro-pyrolyzer
- 17 June 2022
- Published by Elsevier in Bioresource Technology
- Vol. 359, 127500
MgO-modified activated biochar for biojet fuels from pyrolysis of sawdust on a simple tandem micro-pyrolyzer
- Open Access
- 3 December 2021
- Published by MDPI AG in Sustainability
- Vol. 13 (23) , 13386
Kinetic Analysis for the Catalytic Pyrolysis of Polypropylene over Low Cost Mineral Catalysts
A kinetic analysis of non-catalytic pyrolysis (NCP) and catalytic pyrolysis (CP) of polypropylene (PP) with different catalysts was performed using thermogravimetric analysis (TGA) and kinetic models. Three kinds of low-cost natural catalysts were used to maximize the cost-effectiveness of the process: natural zeolite (NZ), bentonite, olivine, and a mesoporous catalyst, Al-MCM-41. The decomposition temperature of PP and apparent activation energy (Ea) were obtained from the TGA results at multiple heating rates, and a model-free kinetic analysis was performed using the Flynn–Wall–Ozawa model. TGA indicated that the maximum decomposition temperature (Tmax) of the PP was shifted from 464 °C to 347 °C with Al-MCM-41 and 348 °C with bentonite, largely due to their strong acidity and large pore size. Although olivine had a large pore size, the Tmax of PP was only shifted to 456 °C, because of its low acidity. The differential TG (DTG) curve of PP over NZ revealed a two-step mechanism. The Tmax of the first peak on the DTG curve of PP with NZ was 376 °C due to the high acidity of NZ. On the other hand, that of the second peak was higher (474 °C) than the non-catalytic reaction. The Ea values at each conversion were also decreased when using the catalysts, except olivine. At <0.5 conversion, the Ea obtained from the CP of PP with NZ was lower than that with the other catalysts: Al-MCM-41, bentonite, and olivine, in that order. The Ea for the CP of PP with NZ increased more rapidly, to 193 kJ/mol at 0.9 conversion, than the other catalysts.
- 3 December 2021
- Published by MDPI AG in Sustainability
- Vol. 13 (23) , 13386
Open AccessKinetic Analysis for the Catalytic Pyrolysis of Polypropylene over Low Cost Mineral Catalysts
A kinetic analysis of non-catalytic pyrolysis (NCP) and catalytic pyrolysis (CP) of polypropylene (PP) with different catalysts was performed using thermogravimetric analysis (TGA) and kinetic models. Three kinds of low-cost natural catalysts were used to maximize the cost-effectiveness of the process: natural zeolite (NZ), bentonite, olivine, and a mesoporous catalyst, Al-MCM-41. The decomposition temperature of PP and apparent activation energy (Ea) were obtained from the TGA results at multiple heating rates, and a model-free kinetic analysis was performed using the Flynn–Wall–Ozawa model. TGA indicated that the maximum decomposition temperature (Tmax) of the PP was shifted from 464 °C to 347 °C with Al-MCM-41 and 348 °C with bentonite, largely due to their strong acidity and large pore size. Although olivine had a large pore size, the Tmax of PP was only shifted to 456 °C, because of its low acidity. The differential TG (DTG) curve of PP over NZ revealed a two-step mechanism. The Tmax of the first peak on the DTG curve of PP with NZ was 376 °C due to the high acidity of NZ. On the other hand, that of the second peak was higher (474 °C) than the non-catalytic reaction. The Ea values at each conversion were also decreased when using the catalysts, except olivine. At <0.5 conversion, the Ea obtained from the CP of PP with NZ was lower than that with the other catalysts: Al-MCM-41, bentonite, and olivine, in that order. The Ea for the CP of PP with NZ increased more rapidly, to 193 kJ/mol at 0.9 conversion, than the other catalysts.
- Open Access
- 20 November 2021
- Published by MDPI AG in Sustainability
- Vol. 13 (22) , 12856
Chemical Feedstock Recovery via the Pyrolysis of Electronically Heated Tobacco Wastes
The pyrolysis of waste electronically heated tobacco (EHT), consisting of tobacco leaves (TL), a poly-lactic acid (PLA) filter, and a cellulose acetate (CA) filter, was investigated using thermogravimetric (TG) and pyrolyzer–gas chromatography/mass spectrometry (Py-GC/MS) analysis. The pyrolytic properties of waste EHT obtained after smoking were comparable to those of fresh EHT. Although the maximum decomposition temperatures (TmaxS) of waste TL and CA were similar to those of fresh EHT components, the Tmax of waste PLA was slightly higher than that of fresh PLA due to smoldering. The Tmaxs of PLA and CA were lowered when they were co-pyrolyzed with TL due to interactions between pyrolysis intermediates. The apparent activation energies for the non-isothermal pyrolysis of waste EHT components were higher than those of fresh EHT components. Py-GC/MS analysis results indicated that considerable amounts of chemical feedstocks, such as nicotine and limonene from TL, caprolactone and lactide from PLA, and acetic acid and triacetin from CA, can be recovered by simple pyrolysis of EHT. Co-pyrolysis of TL, PLA, and CA revealed that the experimental amount of lactide was much larger than the calculated value, suggesting its synergistic formation.
- 20 November 2021
- Published by MDPI AG in Sustainability
- Vol. 13 (22) , 12856
Open AccessChemical Feedstock Recovery via the Pyrolysis of Electronically Heated Tobacco Wastes
The pyrolysis of waste electronically heated tobacco (EHT), consisting of tobacco leaves (TL), a poly-lactic acid (PLA) filter, and a cellulose acetate (CA) filter, was investigated using thermogravimetric (TG) and pyrolyzer–gas chromatography/mass spectrometry (Py-GC/MS) analysis. The pyrolytic properties of waste EHT obtained after smoking were comparable to those of fresh EHT. Although the maximum decomposition temperatures (TmaxS) of waste TL and CA were similar to those of fresh EHT components, the Tmax of waste PLA was slightly higher than that of fresh PLA due to smoldering. The Tmaxs of PLA and CA were lowered when they were co-pyrolyzed with TL due to interactions between pyrolysis intermediates. The apparent activation energies for the non-isothermal pyrolysis of waste EHT components were higher than those of fresh EHT components. Py-GC/MS analysis results indicated that considerable amounts of chemical feedstocks, such as nicotine and limonene from TL, caprolactone and lactide from PLA, and acetic acid and triacetin from CA, can be recovered by simple pyrolysis of EHT. Co-pyrolysis of TL, PLA, and CA revealed that the experimental amount of lactide was much larger than the calculated value, suggesting its synergistic formation.
- 1 July 2021
- Published by American Scientific Publishers in Journal of Nanoscience and Nanotechnology
- Vol. 21 (7) , 3872-3876
Kinetic Analysis for the Catalytic Pyrolysis of Wood Plastic Composite Over Al-MCM-41
This study examined the catalytic effects of Al-MCM-41 on the pyrolysis of wood plastic composite via the thermogravimetric analysis (TGA) and model-free kinetic analysis. Al-MCM-41 containing nanopores, with a high BET surface area (633 m2/g) and acidity (SiO2/Al2O3:25), reduced the decomposition temperature of wood and plastic mixtures (PE and PP) in a wood-plastic composite. The average activation energy for the catalytic pyrolysis of wood plastic composite, which was calculated via a model-free kinetic analysis method (Ozawa) of TGA, was also lower at all conversions than those of non-catalytic pyrolysis. This suggests that the pores of Al-MCM-41 and its high cracking efficiency allow the effective diffusion of wood plastic composite components.
- 1 July 2021
- Published by American Scientific Publishers in Journal of Nanoscience and Nanotechnology
- Vol. 21 (7) , 3872-3876
Kinetic Analysis for the Catalytic Pyrolysis of Wood Plastic Composite Over Al-MCM-41
This study examined the catalytic effects of Al-MCM-41 on the pyrolysis of wood plastic composite via the thermogravimetric analysis (TGA) and model-free kinetic analysis. Al-MCM-41 containing nanopores, with a high BET surface area (633 m2/g) and acidity (SiO2/Al2O3:25), reduced the decomposition temperature of wood and plastic mixtures (PE and PP) in a wood-plastic composite. The average activation energy for the catalytic pyrolysis of wood plastic composite, which was calculated via a model-free kinetic analysis method (Ozawa) of TGA, was also lower at all conversions than those of non-catalytic pyrolysis. This suggests that the pores of Al-MCM-41 and its high cracking efficiency allow the effective diffusion of wood plastic composite components.