Matias Urrutia
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Matias Urrutia has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Habibu Hussaini
Power Electronics, Machines and Control Group, University of Nottingham, Nottingham, U.K
3 shared publications - Jon Clare
Department of Electrical and Electronic Engineering, University of Nottingham, Nottingham, U.K.
3 shared publications - Roberto Cardenas
Department of Electrical Engineering, Universidad de Chile, Santiago, Chile
3 shared publications - Serhiy Bozhko
Power Electronics Machines and Control Institute, University of Nottingham, Nottingham NG7 2GT, UK
3 shared publications - Tao Yang
Power Electronics, Machines and Control Group, The University of Nottingham, Nottingham, U.K.
3 shared publications - Alan. J. Watson
Power Electronics, Machines and Control Research Institute, University of Nottingham, Nottingham, U.K.
2 shared publications
Latest Publications
- 14 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 10 (3) , 7310-7327
A Low-Complexity Artificial Neural Network-Based Optimal Droop Gain Design Strategy for DC Microgrids Onboard the More Electric Aircraft
This article proposes a new droop control design method based on a “reversed data training” of artificial neural network (ANN). Conventionally, after data collection, the ANN is used for forward mapping the control variables (inputs) and system response (outputs). After training, the ANN model can be used for optimal control design for each specific system performance requirement either through curve fittings or other optimization methods. In our proposed method, however, a reversed data training process is used. The ANN uses system responses as its inputs and control variables as outputs. By doing so, the ANN can identify the requested control variables directly for a given system performance request. In the example aircraft DC microgrid, multiple generation systems feed a common DC bus with droop control implemented. During the data-generating process, different droop coefficient combinations are used, and the resulting power sharing ratios are stored as outputs. However, the ANN is data reversely trained with power sharing ratios as inputs and droop coefficients being the outputs. Through this example, we have shown that the proposed approach is straightforward and effective to derive the optimal droop gains based on desired power sharing requests. The proposed approach is tested in both simulation and experiment.
- 14 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 10 (3) , 7310-7327
A Low-Complexity Artificial Neural Network-Based Optimal Droop Gain Design Strategy for DC Microgrids Onboard the More Electric Aircraft
This article proposes a new droop control design method based on a “reversed data training” of artificial neural network (ANN). Conventionally, after data collection, the ANN is used for forward mapping the control variables (inputs) and system response (outputs). After training, the ANN model can be used for optimal control design for each specific system performance requirement either through curve fittings or other optimization methods. In our proposed method, however, a reversed data training process is used. The ANN uses system responses as its inputs and control variables as outputs. By doing so, the ANN can identify the requested control variables directly for a given system performance request. In the example aircraft DC microgrid, multiple generation systems feed a common DC bus with droop control implemented. During the data-generating process, different droop coefficient combinations are used, and the resulting power sharing ratios are stored as outputs. However, the ANN is data reversely trained with power sharing ratios as inputs and droop coefficients being the outputs. Through this example, we have shown that the proposed approach is straightforward and effective to derive the optimal droop gains based on desired power sharing requests. The proposed approach is tested in both simulation and experiment.
- 3 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 10 (1) , 566-582
Artificial Intelligence-Based Hierarchical Control Design for Current Sharing and Voltage Restoration in DC Microgrid of the More Electric Aircraft
In the conventional droop control method employed in the primary control layer, there is an inherent trade-off between current-sharing accuracy and voltage regulation. Consequently, to achieve both accurate current sharing and maintain the bus voltage at its nominal value, secondary control schemes are implemented. Nevertheless, a proper design of control parameters of an electrical power system (EPS) is important as it has a huge impact on its stability and dynamic features. To that end, this paper proposes a novel artificial intelligent-based design strategy for the optimal design of the power sharing and bus voltage compensation coefficients for the islanded more electric aircraft (MEA) EPS DC microgrid. Through the proposed approach, the bus voltage regulation and dynamic performance of the MEA EPS are improved in different EPS operation conditions when compared with the state-of-art methods. Furthermore, the safety and continuous operation of the electrical loads onboard the MEA are guaranteed. The proposed control approach can be conveniently implemented since there is no need for additional controllers and existing communication infrastructure such as power line communication can be utilized. The effectiveness of the proposed approach is validated in both simulations and hardware-in-the-loop experiments.
- 3 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 10 (1) , 566-582
Artificial Intelligence-Based Hierarchical Control Design for Current Sharing and Voltage Restoration in DC Microgrid of the More Electric Aircraft
In the conventional droop control method employed in the primary control layer, there is an inherent trade-off between current-sharing accuracy and voltage regulation. Consequently, to achieve both accurate current sharing and maintain the bus voltage at its nominal value, secondary control schemes are implemented. Nevertheless, a proper design of control parameters of an electrical power system (EPS) is important as it has a huge impact on its stability and dynamic features. To that end, this paper proposes a novel artificial intelligent-based design strategy for the optimal design of the power sharing and bus voltage compensation coefficients for the islanded more electric aircraft (MEA) EPS DC microgrid. Through the proposed approach, the bus voltage regulation and dynamic performance of the MEA EPS are improved in different EPS operation conditions when compared with the state-of-art methods. Furthermore, the safety and continuous operation of the electrical loads onboard the MEA are guaranteed. The proposed control approach can be conveniently implemented since there is no need for additional controllers and existing communication infrastructure such as power line communication can be utilized. The effectiveness of the proposed approach is validated in both simulations and hardware-in-the-loop experiments.
- 3 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 10 (1) , 2192-2206
Optimal Droop Control Design Using Artificial Intelligent Techniques for Electric Power Systems of More-Electric Aircraft
The design of the droop coefficient is one of the challenges for the droop control of converters, as it plays a key role in enhancing the performance of the droop control method. This paper proposes an artificial neural network (ANN) based technique for the design of optimal droop control of parallel-connected converters in a fast and accurate manner, without imposing an additional computational burden on the system. The developed ANN-based design strategy of droop coefficients is used for load sharing and DC bus voltage regulation for the more electric aircraft application. In the design process, the optimal droop coefficient setting is obtained by evaluating a user-defined fitness function with the aid of a trained ANN-based surrogate model. It is observed that the system performance metrics predicted by the surrogate model matched very well with that obtained from the simulation model. The experimental results show that the selected optimal droop coefficient setting can enhance the performance of the traditional droop control method in both steady and transient conditions.
- 3 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 10 (1) , 2192-2206
Optimal Droop Control Design Using Artificial Intelligent Techniques for Electric Power Systems of More-Electric Aircraft
The design of the droop coefficient is one of the challenges for the droop control of converters, as it plays a key role in enhancing the performance of the droop control method. This paper proposes an artificial neural network (ANN) based technique for the design of optimal droop control of parallel-connected converters in a fast and accurate manner, without imposing an additional computational burden on the system. The developed ANN-based design strategy of droop coefficients is used for load sharing and DC bus voltage regulation for the more electric aircraft application. In the design process, the optimal droop coefficient setting is obtained by evaluating a user-defined fitness function with the aid of a trained ANN-based surrogate model. It is observed that the system performance metrics predicted by the surrogate model matched very well with that obtained from the simulation model. The experimental results show that the selected optimal droop coefficient setting can enhance the performance of the traditional droop control method in both steady and transient conditions.
- 30 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 70 (9) , 8723-8733
Continuous Control Set Model Predictive Control of a Modular Multilevel Converter for Drive Applications
The modular multilevel converter is a good alternative for high-power, medium-voltage drive applications due to its modularity and scalability. However, the control is complex and typically involves several highly coupled circulating current feedback loops implemented using single-input single-output design tools. In addition, each circulating current has many different frequency components and electrical sequences to increase the degrees of freedom in the controller. In this work, the use of continuous control set model predictive control is proposed in order to include cross-coupling and interactions between the state variables and to consider the system constraints, such as maximum current and maximum output voltage. The controller is intended for drive applications and is designed to operate with good dynamic performance over the entire speed range of the machine. The control methodology proposed is experimentally validated using an 18-cell MMC prototype driving a cage machine. Additional experimental tests are performed using PLECS-RT HIL platforms.
- 30 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 70 (9) , 8723-8733
Continuous Control Set Model Predictive Control of a Modular Multilevel Converter for Drive Applications
The modular multilevel converter is a good alternative for high-power, medium-voltage drive applications due to its modularity and scalability. However, the control is complex and typically involves several highly coupled circulating current feedback loops implemented using single-input single-output design tools. In addition, each circulating current has many different frequency components and electrical sequences to increase the degrees of freedom in the controller. In this work, the use of continuous control set model predictive control is proposed in order to include cross-coupling and interactions between the state variables and to consider the system constraints, such as maximum current and maximum output voltage. The controller is intended for drive applications and is designed to operate with good dynamic performance over the entire speed range of the machine. The control methodology proposed is experimentally validated using an 18-cell MMC prototype driving a cage machine. Additional experimental tests are performed using PLECS-RT HIL platforms.
- 9 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (5) , 5731-5748
Continuous Set Model Predictive Control for Energy Management of Modular Multilevel Matrix Converters
The modular multilevel matrix converter (M 3 C) is an ac to ac power converter composed of 9 arms and is proposed for high power applications such as motor drive and wind energy conversion systems. Energy Control of the M 3 C is achieved using four circulating currents, and is frequently divided into the different frequency mode (DFM) and equal frequency mode (EFM). EFM is more challenging, because of the larger capacitor voltage oscillations that can be produced. The control schemes are typically different for EFM/DFM operation and this further increases the complexity. In this article, a continuous-control-set model predictive control for energy management of the M 3 C is proposed. The control scheme is based on solving an equality constrained quadratic programming problem, where the optimal solution is analytically obtained. The result is a single and simple control law to obtain the circulating current references, where good performance is achieved for both EFM and DFM. The proposed strategy is experimentally validated using a scaled-down M 3 C prototype composed of 27 power cells.
- 9 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (5) , 5731-5748
Continuous Set Model Predictive Control for Energy Management of Modular Multilevel Matrix Converters
The modular multilevel matrix converter (M 3 C) is an ac to ac power converter composed of 9 arms and is proposed for high power applications such as motor drive and wind energy conversion systems. Energy Control of the M 3 C is achieved using four circulating currents, and is frequently divided into the different frequency mode (DFM) and equal frequency mode (EFM). EFM is more challenging, because of the larger capacitor voltage oscillations that can be produced. The control schemes are typically different for EFM/DFM operation and this further increases the complexity. In this article, a continuous-control-set model predictive control for energy management of the M 3 C is proposed. The control scheme is based on solving an equality constrained quadratic programming problem, where the optimal solution is analytically obtained. The result is a single and simple control law to obtain the circulating current references, where good performance is achieved for both EFM and DFM. The proposed strategy is experimentally validated using a scaled-down M 3 C prototype composed of 27 power cells.
- 8 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 9 (5) , 6069-6085
Circulating Current Control for the Modular Multilevel Matrix Converter Based on Model Predictive Control
In this work, a continuous-control-set model predictive control (CCS-MPC) strategy, with a saturation scheme for protection, is presented for regulating the circulating currents of a modular multilevel matrix converter (M3C). The proposed approach is based on a state-space model of the M3C and allows protection and better utilization of the devices through a saturation scheme, which directly limits the arm currents and cluster output voltages by integrating the corresponding bounds as constraints of the CCS-MPC formulation. In order to solve the inherent optimization problem associated with the CCS-MPC, an active-set algorithm is implemented. Experimental and simulation results from a 27-cell M3C prototype validate the proposed strategy and illustrate the good performance achieved with the methodology presented in this work.
- 8 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 9 (5) , 6069-6085
Circulating Current Control for the Modular Multilevel Matrix Converter Based on Model Predictive Control
In this work, a continuous-control-set model predictive control (CCS-MPC) strategy, with a saturation scheme for protection, is presented for regulating the circulating currents of a modular multilevel matrix converter (M3C). The proposed approach is based on a state-space model of the M3C and allows protection and better utilization of the devices through a saturation scheme, which directly limits the arm currents and cluster output voltages by integrating the corresponding bounds as constraints of the CCS-MPC formulation. In order to solve the inherent optimization problem associated with the CCS-MPC, an active-set algorithm is implemented. Experimental and simulation results from a 27-cell M3C prototype validate the proposed strategy and illustrate the good performance achieved with the methodology presented in this work.
- 1 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Advanced lead-acid battery models for the state-of-charge estimation in an isolated microgrid
In order to compare and improve battery energy storage system (BESS) models, this work exhibits a comparative study of the Coppeti, the Coulomb counting, and the Thevenin based models of the State of Charge (SoC) for lead-acid batteries. Additionally, a multi-model estimator that merges and exploits the benefits of aforementioned models is proposed by using an extended Kalman filter (EKF). The performance of the different SoC models are evaluated by means of simulations in a economic dispatch problem of an isolated microgrid with an Energy Management System (EMS). The Comparative study of the SoC models is done using real operation data from the Huatacondo's microgrid with an EMS based on a rolling horizon strategy. As shown in the results, the operating costs of the microgrid are considerably reduced when the multi-model estimator is used, showing a direct impact in the economical costs of the system.
- 1 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Advanced lead-acid battery models for the state-of-charge estimation in an isolated microgrid
In order to compare and improve battery energy storage system (BESS) models, this work exhibits a comparative study of the Coppeti, the Coulomb counting, and the Thevenin based models of the State of Charge (SoC) for lead-acid batteries. Additionally, a multi-model estimator that merges and exploits the benefits of aforementioned models is proposed by using an extended Kalman filter (EKF). The performance of the different SoC models are evaluated by means of simulations in a economic dispatch problem of an isolated microgrid with an Energy Management System (EMS). The Comparative study of the SoC models is done using real operation data from the Huatacondo's microgrid with an EMS based on a rolling horizon strategy. As shown in the results, the operating costs of the microgrid are considerably reduced when the multi-model estimator is used, showing a direct impact in the economical costs of the system.