Da Zong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Da Zong has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Kewei Ding
School of Civil Engineering, Anhui Jianzhu University, Hefei 230601, China
2 shared publications - Shulin He
School of Civil Engineering, Anhui Jianzhu University, Hefei 230601, China
2 shared publications Jian Chen
Jianhua Building Materials Technology (Huai’an) Co. Ltd, No. 1, Yanbei Avenue East Rd., Huai’an 223215, China
1 shared publicationLi Wang
Huai’an Water Conservancy Survey and Design Institute Co., Ltd, No. 9, Shenzhen Rd., Huai’an 223005, China
1 shared publicationMing Li
College of Civil and Transportation Engineering, Hohai University, No. 1 Xikang Road, Nanjing 210024, China
1 shared publicationPengfei Xu
Huai’an Water Conservancy Survey and Design Institute Co., Ltd, No. 9, Shenzhen Rd., Huai’an 223005, China
1 shared publication
Latest Publications
- Open Access
- 8 December 2023
- Published by Wiley in Advances in Civil Engineering
- Vol. 2023, 1-15
Effect of Reinforcement Forms on the Load Bearing Capacity of Prefabricated Box Culvert
Box culvert structure was an essential part of modern infrastructure. Due to the advantages of low pollution and convenient construction, the prefabricated box culvert (PBC) has been gradually utilized in engineering. However, the investigations on load bearing capacity of PBC in different reinforcement forms with same reinforcement ratios were still lack. In the present research, one PBC specimen was tested and discussed by the finite-element analysis (FEA) on load bearing capacity under four-point bending. The load bearing capacity of another three PBCs in different reinforcement forms with the same reinforcement ratios was discussed by the FEA. Results of experimental and numerical investigations showed that: (1) a number of flexural cracks were observed in the midspan bottom of upper slab of PBC, and finally shear failure was observed in bending–shear zone of upper slab of PBC; (2) the number of concrete cracking, plastic deformation of PBC, and stress of rebars reduced by increasing the area of tensile rebars in PBC with reducing the area of compressive rebars under same reinforcement ratios; (3) the ductility and load bearing capacity of PBC increased by increasing the area of tensile rebars with reducing the area of compressive rebars.
- 8 December 2023
- Published by Wiley in Advances in Civil Engineering
- Vol. 2023, 1-15
Open AccessEffect of Reinforcement Forms on the Load Bearing Capacity of Prefabricated Box Culvert
Box culvert structure was an essential part of modern infrastructure. Due to the advantages of low pollution and convenient construction, the prefabricated box culvert (PBC) has been gradually utilized in engineering. However, the investigations on load bearing capacity of PBC in different reinforcement forms with same reinforcement ratios were still lack. In the present research, one PBC specimen was tested and discussed by the finite-element analysis (FEA) on load bearing capacity under four-point bending. The load bearing capacity of another three PBCs in different reinforcement forms with the same reinforcement ratios was discussed by the FEA. Results of experimental and numerical investigations showed that: (1) a number of flexural cracks were observed in the midspan bottom of upper slab of PBC, and finally shear failure was observed in bending–shear zone of upper slab of PBC; (2) the number of concrete cracking, plastic deformation of PBC, and stress of rebars reduced by increasing the area of tensile rebars in PBC with reducing the area of compressive rebars under same reinforcement ratios; (3) the ductility and load bearing capacity of PBC increased by increasing the area of tensile rebars with reducing the area of compressive rebars.
- Open Access
Experimental and Parametric Study on Seismic Behavior of Steel Frame with ALC Panels
This paper presents a new type of connector which is used in prefabricated structures for attaching the autoclaved lightweight concrete panels to the steel frame. The new type of connector is composed of an L-node plate and a Z-node plate and is termed as the “pendulous Z-plate connector”. For examining the seismic behavior of the new connector, two full-scale steel frames with cladding panel walls, in which the ALC panels are connected to the steel frame by both classical and new connectors, were tested under quasi-static loading. The failure mode, hysteresis performance, energy dissipation, and stiffness degradation of the structures were measured and compared. The experimental results indicate that the new connector facilitates a better structural performance of cladding panel walls than the classical connector in terms of the coordinating deformation, the energy dissipation, and the load-carrying capacity at the yielding and the ultimate stages. In addition, for in-depth analysis of the failure mechanism, the finite element modeling was conducted and validated based on the comparison with the experimental results. Further parametric studies are carried out to find out the effect of bolt grades on the structure.
Open AccessExperimental and Parametric Study on Seismic Behavior of Steel Frame with ALC Panels
This paper presents a new type of connector which is used in prefabricated structures for attaching the autoclaved lightweight concrete panels to the steel frame. The new type of connector is composed of an L-node plate and a Z-node plate and is termed as the “pendulous Z-plate connector”. For examining the seismic behavior of the new connector, two full-scale steel frames with cladding panel walls, in which the ALC panels are connected to the steel frame by both classical and new connectors, were tested under quasi-static loading. The failure mode, hysteresis performance, energy dissipation, and stiffness degradation of the structures were measured and compared. The experimental results indicate that the new connector facilitates a better structural performance of cladding panel walls than the classical connector in terms of the coordinating deformation, the energy dissipation, and the load-carrying capacity at the yielding and the ultimate stages. In addition, for in-depth analysis of the failure mechanism, the finite element modeling was conducted and validated based on the comparison with the experimental results. Further parametric studies are carried out to find out the effect of bolt grades on the structure.
- Open Access
- 19 November 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (22) , 10990
Experimental and Finite Element Analysis of External ALC Panel Steel Frames with New Semi-Rigid Connector
In this paper, a new ALC panel connector was proposed. It has a good engineering economy and high fault tolerance. A quasistatic loading experiment was carried out to verify the feasibility of the external ALC panel steel frame under seismic loading. The test phenomena, hysteretic curve, skeleton curve, stiffness degradation, and energy dissipation of two sets of full-scale specimens were analyzed and discussed. Moreover, the simulation of pendulous Z-panel connectors with different thicknesses was carried out using ABAQUS software. The comparison reveals that the semi-rigid connection has a full hysteresis curve, good energy dissipation capacity, and a 15% increase in peak load capacity. Finally, similar results for different thicknesses in the use of pendulous Z-panel connectors reveal that using the 6 mm connector may be the most economical solution for engineering.
- 19 November 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (22) , 10990
Open AccessExperimental and Finite Element Analysis of External ALC Panel Steel Frames with New Semi-Rigid Connector
In this paper, a new ALC panel connector was proposed. It has a good engineering economy and high fault tolerance. A quasistatic loading experiment was carried out to verify the feasibility of the external ALC panel steel frame under seismic loading. The test phenomena, hysteretic curve, skeleton curve, stiffness degradation, and energy dissipation of two sets of full-scale specimens were analyzed and discussed. Moreover, the simulation of pendulous Z-panel connectors with different thicknesses was carried out using ABAQUS software. The comparison reveals that the semi-rigid connection has a full hysteresis curve, good energy dissipation capacity, and a 15% increase in peak load capacity. Finally, similar results for different thicknesses in the use of pendulous Z-panel connectors reveal that using the 6 mm connector may be the most economical solution for engineering.