Ivan Gabrijel
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ivan Gabrijel has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Marija Jelčić Rukavina
University of Zagreb
3 shared publications - Nina Štirmer
University of Zagreb
3 shared publications - Marijan Skazlić
Materials Department, Faculty of Civil Engineering, University of Zagreb, Fra Andrije Kačića Miošića 26, 10000 Zagreb, Croatia
2 shared publications - Aljoša Šajna
Zavod Za gradbeništvo (ZAG) Slovenije, Slovenian National Building and Civil Engineering Institute
1 shared publication - Ana Mladenovič
Slovenian National Building and Civil Engineering Institute, Dimičeva ulica 12, 1000 Ljubljana, Slovenia
1 shared publication Christian U. Grosse
Technische Universität München
1 shared publication
Latest Publications
- Open Access
- 14 April 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (8) , 4309
Experimental Analysis of Creep and Shrinkage of Self-Compacting Concrete with Recycled Concrete Aggregates
The recycling of old concrete from the demolition of concrete structures is necessary for the rational use of natural aggregate resources. Recycled concrete aggregates (RCAs) are the highest quality recycled aggregates as they are the closest to natural aggregates. However, the use of RCAs is always associated with greater fluctuations and usually with a deterioration in workability, mechanical properties and long-term properties. The use of RCA in self-compacting concrete (SCC), where the proportion of aggregate is lower than in conventional concrete, is one way of mitigating the effects of RCAs. In this paper, the effects of coarse and fine RCA are investigated, focusing on dimensional changes due to shrinkage and creep. SCC mixes were developed in which the dolomite aggregates were partially or completely replaced by RCAs and additionally mixes in which 50% of the cement was replaced by fly ash. The average shrinkage strain measured after 180 days increased from 0.34 mm/m for a mix with natural aggregates to 1.04 mm/m for a mix made entirely with RCAs, showing an almost proportional increase in strain with RCA content. At the same age, the creep compliance ranged from 0.07 GPa−1 for the mix with natural aggregates to 0.34 GPa−1 for the mix made entirely with RCAs, and is most strongly correlated with hardened concrete density.
- 14 April 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (8) , 4309
Open AccessExperimental Analysis of Creep and Shrinkage of Self-Compacting Concrete with Recycled Concrete Aggregates
The recycling of old concrete from the demolition of concrete structures is necessary for the rational use of natural aggregate resources. Recycled concrete aggregates (RCAs) are the highest quality recycled aggregates as they are the closest to natural aggregates. However, the use of RCAs is always associated with greater fluctuations and usually with a deterioration in workability, mechanical properties and long-term properties. The use of RCA in self-compacting concrete (SCC), where the proportion of aggregate is lower than in conventional concrete, is one way of mitigating the effects of RCAs. In this paper, the effects of coarse and fine RCA are investigated, focusing on dimensional changes due to shrinkage and creep. SCC mixes were developed in which the dolomite aggregates were partially or completely replaced by RCAs and additionally mixes in which 50% of the cement was replaced by fly ash. The average shrinkage strain measured after 180 days increased from 0.34 mm/m for a mix with natural aggregates to 1.04 mm/m for a mix made entirely with RCAs, showing an almost proportional increase in strain with RCA content. At the same age, the creep compliance ranged from 0.07 GPa−1 for the mix with natural aggregates to 0.34 GPa−1 for the mix made entirely with RCAs, and is most strongly correlated with hardened concrete density.
- 11 June 2023
- Published by Springer Nature
- p. 604-611
Effect of Elevated Temperatures on Concrete Made with Ash from Wood Biomass and Recycled Polymer Fibers from Waste Rubber
- 11 June 2023
- Published by Springer Nature
- p. 604-611
Effect of Elevated Temperatures on Concrete Made with Ash from Wood Biomass and Recycled Polymer Fibers from Waste Rubber
- Open Access
- 14 December 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (24) , 12859
Long-Term Behavior of Concrete Containing Wood Biomass Fly Ash
Wood biomass is widely used in the European Union as a fuel for the production of heat and electrical energy, generating a considerable amount of ash. The disposal of ash, especially its finest fraction, requires proper engineering solutions, since these particles contain heavy metals and can easily pollute soil, groundwater, or air. In this work, wood fly ash with a high amount of pozzolanic oxides and one with a high CaO content were used in concrete as a 15% and 30% cement replacement. Incorporation of wood ash in concrete reduced the 28-day compressive strength of concrete by up to 37%, which was attributed to the low stiffness of the wood ash particles, while the 2-year compressive strength indicated very low pozzolanic reactivity. The capillary absorption of concrete increased with the increase in the ash content, but almost no influence on the gas permeability was observed. Wood fly ash with high CaO content reduced the drying shrinkage of concrete by up to 65% after 1 year. In a mix with 30% of high CaO fly ash, swelling occurred in the first days of hydration, which was attributed to the volume expansion due to the formation of portlandite and brucite, but did not lead to cracking or a decrease in long-term compressive strength.
- 14 December 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (24) , 12859
Open AccessLong-Term Behavior of Concrete Containing Wood Biomass Fly Ash
Wood biomass is widely used in the European Union as a fuel for the production of heat and electrical energy, generating a considerable amount of ash. The disposal of ash, especially its finest fraction, requires proper engineering solutions, since these particles contain heavy metals and can easily pollute soil, groundwater, or air. In this work, wood fly ash with a high amount of pozzolanic oxides and one with a high CaO content were used in concrete as a 15% and 30% cement replacement. Incorporation of wood ash in concrete reduced the 28-day compressive strength of concrete by up to 37%, which was attributed to the low stiffness of the wood ash particles, while the 2-year compressive strength indicated very low pozzolanic reactivity. The capillary absorption of concrete increased with the increase in the ash content, but almost no influence on the gas permeability was observed. Wood fly ash with high CaO content reduced the drying shrinkage of concrete by up to 65% after 1 year. In a mix with 30% of high CaO fly ash, swelling occurred in the first days of hydration, which was attributed to the volume expansion due to the formation of portlandite and brucite, but did not lead to cracking or a decrease in long-term compressive strength.
- Open Access
Residual Compressive Behavior of Self-Compacting Concrete after High Temperature Exposure—Influence of Binder Materials
This paper presents an experimental investigation of the compressive behavior of high-strength self-compacting concrete exposed to temperatures up to 600 °C. Ten different concrete compositions were tested, in which part of the cement (by weight) was replaced by three different mineral additives (5–15% metakaolin, 20–40% fly ash and 5–15% limestone). The stress–strain curves, compressive strength, modulus of elasticity and strain at peak stress were evaluated from uniaxial compression tests. Scanning electron microscope micrographs were also taken to evaluate the damage caused by the high temperatures. A sharp decrease in mechanical properties and an increase in peak strain were observed already after 200 °C for all mixes tested. The different mineral additives used in this study affected the variations of residual compressive strength by 24% and peak strain by 38%, while the variations of residual modulus elasticity were 14%. Comparing the obtained results with the recommendations for compressive strength given in regulatory code EN 1992-1-2 for high strength concrete, it can be concluded that the strength loss observed in EN 1992-1-2 at temperatures up to 400 °C is too conservative. The Popovics model for the relationship between stress and strain provided a good approximation for the experimentally determined stress–strain curves at different temperatures.
Open AccessResidual Compressive Behavior of Self-Compacting Concrete after High Temperature Exposure—Influence of Binder Materials
This paper presents an experimental investigation of the compressive behavior of high-strength self-compacting concrete exposed to temperatures up to 600 °C. Ten different concrete compositions were tested, in which part of the cement (by weight) was replaced by three different mineral additives (5–15% metakaolin, 20–40% fly ash and 5–15% limestone). The stress–strain curves, compressive strength, modulus of elasticity and strain at peak stress were evaluated from uniaxial compression tests. Scanning electron microscope micrographs were also taken to evaluate the damage caused by the high temperatures. A sharp decrease in mechanical properties and an increase in peak strain were observed already after 200 °C for all mixes tested. The different mineral additives used in this study affected the variations of residual compressive strength by 24% and peak strain by 38%, while the variations of residual modulus elasticity were 14%. Comparing the obtained results with the recommendations for compressive strength given in regulatory code EN 1992-1-2 for high strength concrete, it can be concluded that the strength loss observed in EN 1992-1-2 at temperatures up to 400 °C is too conservative. The Popovics model for the relationship between stress and strain provided a good approximation for the experimentally determined stress–strain curves at different temperatures.
- Open Access
Influence of Wood Fly Ash on Concrete Properties through Filling Effect Mechanism
This paper presents the results of an experimental study aimed at determining the influence of wood fly ash (WFA) from three Croatian power plants on the properties of concrete. First, the chemical and physical properties of WFA’s were determined. It was found that these properties are highly influenced by combustion technology, the type and parts of wood used as fuel, and the local operating conditions. Subsequently, workability, heat of hydration, stiffness development, 28-day compressive strength, apparent porosity, and capillary absorption were determined on concrete mixes prepared with WFA as cement replacement from 5–45% by weight. Cement replacement up to 15% with the finest WFA accelerated hydration, stiffness development, and increased compressive strength of concrete up to 18%, while replacement with coarser WFA’s led to a decrease in compressive strength of up to 5% and had more gradual heat liberation. The dominant effect that could explain these findings is attributed to the filler and filling effect mechanisms. At the same time replacement content of up to 45% had very little effect on capillary absorption and could give concrete with sufficiently high compressive strength to be suitable for construction purposes.
Open AccessInfluence of Wood Fly Ash on Concrete Properties through Filling Effect Mechanism
This paper presents the results of an experimental study aimed at determining the influence of wood fly ash (WFA) from three Croatian power plants on the properties of concrete. First, the chemical and physical properties of WFA’s were determined. It was found that these properties are highly influenced by combustion technology, the type and parts of wood used as fuel, and the local operating conditions. Subsequently, workability, heat of hydration, stiffness development, 28-day compressive strength, apparent porosity, and capillary absorption were determined on concrete mixes prepared with WFA as cement replacement from 5–45% by weight. Cement replacement up to 15% with the finest WFA accelerated hydration, stiffness development, and increased compressive strength of concrete up to 18%, while replacement with coarser WFA’s led to a decrease in compressive strength of up to 5% and had more gradual heat liberation. The dominant effect that could explain these findings is attributed to the filler and filling effect mechanisms. At the same time replacement content of up to 45% had very little effect on capillary absorption and could give concrete with sufficiently high compressive strength to be suitable for construction purposes.
- 2 March 2020
- Published by Elsevier in Construction and Building Materials
- Vol. 247, 118542
Practice on creating a common reference concrete for Round Robin Testing programmes based on the experience from COST Action TU1404
- 2 March 2020
- Published by Elsevier in Construction and Building Materials
- Vol. 247, 118542
Practice on creating a common reference concrete for Round Robin Testing programmes based on the experience from COST Action TU1404
- 19 February 2020
- Published by Springer Nature
- p. 23-68
Ultrasonic Techniques for Determination and Monitoring Various Properties of Cementitious Materials at Early Ages
- 19 February 2020
- Published by Springer Nature
- p. 23-68
Ultrasonic Techniques for Determination and Monitoring Various Properties of Cementitious Materials at Early Ages
- 17 June 2015
- Published by Emerald Publishing in Journal of Structural Fire Engineering
- Vol. 6 (3) , 177-184
Mechanical Properties of Self-Compacting Concrete with Different Mineral Aditives After High Temperature Exposure
This paper presents an experimental research on the performance of high-strength selfcompacting concrete (SCC) with different mineral additives after exposure to high temperatures of up to 600°C. For this purpose, four SCC mixtures were studied: one reference and three mixtures where the Portland cement was replaced with mineral additive (fly ash, metakaolin and limestone) in certain proportions. After natural cooling in the furnace, compressive strength and static modulus of elasticity were determined and compared to results obtained from other studies and those provided in EN 1992-1-2 and EN 1994-1-2 for normal-vibrated concrete. Additionally, acoustic emission (AE) parameters during compression test of heated and unheated specimens were also obtained which showed good non-destructive tool for identifying exposure temperature of the concrete needed for the assessment of concrete structures after fire.
- 17 June 2015
- Published by Emerald Publishing in Journal of Structural Fire Engineering
- Vol. 6 (3) , 177-184
Mechanical Properties of Self-Compacting Concrete with Different Mineral Aditives After High Temperature Exposure
This paper presents an experimental research on the performance of high-strength selfcompacting concrete (SCC) with different mineral additives after exposure to high temperatures of up to 600°C. For this purpose, four SCC mixtures were studied: one reference and three mixtures where the Portland cement was replaced with mineral additive (fly ash, metakaolin and limestone) in certain proportions. After natural cooling in the furnace, compressive strength and static modulus of elasticity were determined and compared to results obtained from other studies and those provided in EN 1992-1-2 and EN 1994-1-2 for normal-vibrated concrete. Additionally, acoustic emission (AE) parameters during compression test of heated and unheated specimens were also obtained which showed good non-destructive tool for identifying exposure temperature of the concrete needed for the assessment of concrete structures after fire.