Guoqing Shi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Guoqing Shi has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
Guangping Teng
College of Safety Engineering, School of Safety Engineering, China University of Mining and Technology, Xuzhou, China
4 shared publicationsYanming Wang
4 shared publicationsDeming Wang
3 shared publicationsJintuo Zhu
College of Safety Engineering, School of Safety Engineering, China University of Mining and Technology, Xuzhou, China
3 shared publicationsHaohui Ma
State Key Laboratory for Coal Mine Disaster Prevention and Control, China University of Mining and Technology, Xuzhou, China
2 shared publicationsJiamin Qi
School of Safety Engineering, China University of Mining and Technology, Xuzhou, China
2 shared publications
Latest Publications
- 8 September 2026
- Published by Springer Nature in Mining, Metallurgy & Exploration
- p. 1-29
Determining the Mean Wind Speed Point in Mine Roadways
- 8 September 2026
- Published by Springer Nature in Mining, Metallurgy & Exploration
- p. 1-29
Determining the Mean Wind Speed Point in Mine Roadways
- 12 August 2025
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 36 (8)
Improvement of wind speed measurement in mine roadway by transit-time difference method: correction of error caused by nonlinear trajectory of ultrasonic in turbulent flow
The difference between the assumed conditions and the actual engineering scenario leads to systematic theoretical error when the transit-time difference method is applied to measure the flow rate in turbulent field. This paper focuses on the theoretical error in the turbulent of such a geometric scale as the coal mine roadway. A three-dimensional coupled simulation model of ultrasonic propagation integrating pressure acoustics, computational fluid dynamics and ray acoustics was established. A large number of simulation cases were designed and the influencing factors of theoretical error were quantified using statistical analysis method. The results show that the theoretical error is positively correlated with flow rate and wall roughness, and negatively correlated with equivalent diameter of roadway section. Compared to the theoretically assumed uniform flow field, the propagation time of ultrasonic waves in the turbulent flow field is shorter in the downstream direction and longer in the upstream direction. The relative value of the theoretical error is about 2%, and the absolute value is described by the multiple regression prediction model. The high fitting degree of the model indicates that 96.9% of the variation in absolute error could be reliably explained, which is beneficial to improve the accuracy and engineering applicability of the transit-time difference method.
- 12 August 2025
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 36 (8)
Improvement of wind speed measurement in mine roadway by transit-time difference method: correction of error caused by nonlinear trajectory of ultrasonic in turbulent flow
The difference between the assumed conditions and the actual engineering scenario leads to systematic theoretical error when the transit-time difference method is applied to measure the flow rate in turbulent field. This paper focuses on the theoretical error in the turbulent of such a geometric scale as the coal mine roadway. A three-dimensional coupled simulation model of ultrasonic propagation integrating pressure acoustics, computational fluid dynamics and ray acoustics was established. A large number of simulation cases were designed and the influencing factors of theoretical error were quantified using statistical analysis method. The results show that the theoretical error is positively correlated with flow rate and wall roughness, and negatively correlated with equivalent diameter of roadway section. Compared to the theoretically assumed uniform flow field, the propagation time of ultrasonic waves in the turbulent flow field is shorter in the downstream direction and longer in the upstream direction. The relative value of the theoretical error is about 2%, and the absolute value is described by the multiple regression prediction model. The high fitting degree of the model indicates that 96.9% of the variation in absolute error could be reliably explained, which is beneficial to improve the accuracy and engineering applicability of the transit-time difference method.
- 9 November 2023
- Published by Wiley in Energy Technology
- Vol. 12 (1)
Experimental Study on the Thermal Management Performance of Lithium‐Ion Battery Using Phase‐Change Material at Various Ambient Temperatures
The implementation of a battery thermal management system (BTMS) is crucial to ensuring the optimal functioning of lithium‐ion batteries (LIBs) within an appropriate temperature range. In this study, BTMS with a combination of paraffin wax (PA), expanded graphite, and copper foam (CF) is investigated. The impact of various optimization strategies on battery surface temperature and discharge capacity is investigated, and charging and discharging experiments are performed at different ambient temperature conditions. Moreover, the influence of copper foam arrangement on BTMS is studied. The experimental results demonstrate that PA/CF can lead to a significant battery surface temperature reduction of up to 11.7%. Compared with the side radial arrangement, the front tangential arrangement of closely attaching copper foam to the battery leads to improved results. However, the variation in arrangement has minimal impact on the surface temperature of the battery in extreme environmental conditions. Under low‐temperature conditions, incorporating phase‐change materials could produce insulating effects that supported maintaining battery capacity. In all, this study shows the potential of designing a high‐performance BTMS and contributes to addressing heat accumulation and capacity attenuation during the use of LIBs.
- 9 November 2023
- Published by Wiley in Energy Technology
- Vol. 12 (1)
Experimental Study on the Thermal Management Performance of Lithium‐Ion Battery Using Phase‐Change Material at Various Ambient Temperatures
The implementation of a battery thermal management system (BTMS) is crucial to ensuring the optimal functioning of lithium‐ion batteries (LIBs) within an appropriate temperature range. In this study, BTMS with a combination of paraffin wax (PA), expanded graphite, and copper foam (CF) is investigated. The impact of various optimization strategies on battery surface temperature and discharge capacity is investigated, and charging and discharging experiments are performed at different ambient temperature conditions. Moreover, the influence of copper foam arrangement on BTMS is studied. The experimental results demonstrate that PA/CF can lead to a significant battery surface temperature reduction of up to 11.7%. Compared with the side radial arrangement, the front tangential arrangement of closely attaching copper foam to the battery leads to improved results. However, the variation in arrangement has minimal impact on the surface temperature of the battery in extreme environmental conditions. Under low‐temperature conditions, incorporating phase‐change materials could produce insulating effects that supported maintaining battery capacity. In all, this study shows the potential of designing a high‐performance BTMS and contributes to addressing heat accumulation and capacity attenuation during the use of LIBs.
- Open Access
Organic and Inorganic Hybrid Composite Phase Change Material for Inhibiting the Thermal Runaway of Lithium-Ion Batteries
To deal with the flammability of PA (paraffin), this paper proposes a CPCM (composite phase change material) with a high heat-absorbing capacity for mitigating the thermal runaway of lithium-ion batteries. Two heating power levels were used to trigger thermal runaway in order to investigate the influence of heating power on thermal runaway characteristics and the mitigation effect of the PCM (phase change material). Thermal runaway processes and temperature changes were recorded. The results showed that heating results in a violent reaction of the battery, generating a high temperature and a bright flame, and the burning of PA increases the duration of a steady flame, indicating an increased threat. SA (sodium acetate trihydrate) effectively inhibited PA combustion, and the combustion time was reduced by 40.5%. PA/SA effectively retarded the rise in temperature of the battery, and the temperature rise rate was reduced by 87.3%. Increased heating power caused faster thermal runaway, and the thermal runaway mitigation effect of the CPCM was dramatically reduced. This study may provide a reference for the safe design and improvement of thermal management systems.
Open AccessOrganic and Inorganic Hybrid Composite Phase Change Material for Inhibiting the Thermal Runaway of Lithium-Ion Batteries
To deal with the flammability of PA (paraffin), this paper proposes a CPCM (composite phase change material) with a high heat-absorbing capacity for mitigating the thermal runaway of lithium-ion batteries. Two heating power levels were used to trigger thermal runaway in order to investigate the influence of heating power on thermal runaway characteristics and the mitigation effect of the PCM (phase change material). Thermal runaway processes and temperature changes were recorded. The results showed that heating results in a violent reaction of the battery, generating a high temperature and a bright flame, and the burning of PA increases the duration of a steady flame, indicating an increased threat. SA (sodium acetate trihydrate) effectively inhibited PA combustion, and the combustion time was reduced by 40.5%. PA/SA effectively retarded the rise in temperature of the battery, and the temperature rise rate was reduced by 87.3%. Increased heating power caused faster thermal runaway, and the thermal runaway mitigation effect of the CPCM was dramatically reduced. This study may provide a reference for the safe design and improvement of thermal management systems.
- Open Access
- 27 July 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-14
Research on the air supply adjustment technology of breath-following powered air-purifying respirators
In the hope of reducing the air supply flow of the powered air-purifying respirator (PAPR) and extending the service life of the filter, a breath-following powered air-purifying respirator (BF-PAPR) that can dynamically adjust the air supply flow according to the breathing flow is proposed. The BF-PAPR changes the air supply flow by adjusting the speed of the variable-frequency centrifugal fan according to the air velocity at the half mask outlet (vhm) monitored by the modular wind speed transmitter. In the study, the air supply flow adjustment model of the BF-PAPR is developed. It is found that the filtration resistance barely influences vhm. In addition, under the same mean inhalation flow, the minimum outlet air velocity increases first and then decreases with the increase of the duty cycle variation coefficient (λ), while the maximum outlet air velocity decreases first and then increases. Moreover, the minimum air supply flow of the BF-PAPR is achieved when the standard value of the air velocity is 13.4 m/s and the value of λ is 1. The BF-PAPR can reduce the air supply flow by 6.5%-8.6% and the energy consumption by approximately 20% compared with the PAPR, which is beneficial for reducing the usage cost and extending the continuous working time.
- 27 July 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-14
Open AccessResearch on the air supply adjustment technology of breath-following powered air-purifying respirators
In the hope of reducing the air supply flow of the powered air-purifying respirator (PAPR) and extending the service life of the filter, a breath-following powered air-purifying respirator (BF-PAPR) that can dynamically adjust the air supply flow according to the breathing flow is proposed. The BF-PAPR changes the air supply flow by adjusting the speed of the variable-frequency centrifugal fan according to the air velocity at the half mask outlet (vhm) monitored by the modular wind speed transmitter. In the study, the air supply flow adjustment model of the BF-PAPR is developed. It is found that the filtration resistance barely influences vhm. In addition, under the same mean inhalation flow, the minimum outlet air velocity increases first and then decreases with the increase of the duty cycle variation coefficient (λ), while the maximum outlet air velocity decreases first and then increases. Moreover, the minimum air supply flow of the BF-PAPR is achieved when the standard value of the air velocity is 13.4 m/s and the value of λ is 1. The BF-PAPR can reduce the air supply flow by 6.5%-8.6% and the energy consumption by approximately 20% compared with the PAPR, which is beneficial for reducing the usage cost and extending the continuous working time.
- Open Access
- 21 February 2023
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 18 (2) , e0282026
A numerical simulation method for pressure drop and normal air velocity of pleated filters during dust loading
Pressure drop is an important indicator that affects the filtration performance of the pleated filter, and the deposition of dust particles within the pleats is crucial to the evolution of the pressure drop. In this study, the pressure drop during PM10 loading process was investigated for a series of V-shaped and U-shaped filters with a pleat height of 20 mm and different pleat ratios (the ratio of pleat height to pleat width: α = 0.71–3.57). In the numerical simulations, numerical models suitable for different pleated geometries were obtained through experimental verification on the local air velocity. Then, assuming that the dust cake thickness is proportional to the normal air velocity of the filters, the variation of the pressure drop with the dust deposition is derived by means of successive numerical simulations. This simulation method saved a significant amount of CPU time required for the growth of dust cake. It was found that the relative average deviations between experimental and simulated pressure drops were 3.12% and 1.19% for V-shaped and U-shaped filters, respectively. Furthermore, it was found that under the same pleat ratio and the mass of dust deposition per unit area, both the pressure drop and unevenness of normal air velocity of the U-shaped filter were lower than the V-shaped filter. Therefore, the U-shaped filter is recommended due to its better filtration performance.
- 21 February 2023
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 18 (2) , e0282026
Open AccessA numerical simulation method for pressure drop and normal air velocity of pleated filters during dust loading
Pressure drop is an important indicator that affects the filtration performance of the pleated filter, and the deposition of dust particles within the pleats is crucial to the evolution of the pressure drop. In this study, the pressure drop during PM10 loading process was investigated for a series of V-shaped and U-shaped filters with a pleat height of 20 mm and different pleat ratios (the ratio of pleat height to pleat width: α = 0.71–3.57). In the numerical simulations, numerical models suitable for different pleated geometries were obtained through experimental verification on the local air velocity. Then, assuming that the dust cake thickness is proportional to the normal air velocity of the filters, the variation of the pressure drop with the dust deposition is derived by means of successive numerical simulations. This simulation method saved a significant amount of CPU time required for the growth of dust cake. It was found that the relative average deviations between experimental and simulated pressure drops were 3.12% and 1.19% for V-shaped and U-shaped filters, respectively. Furthermore, it was found that under the same pleat ratio and the mass of dust deposition per unit area, both the pressure drop and unevenness of normal air velocity of the U-shaped filter were lower than the V-shaped filter. Therefore, the U-shaped filter is recommended due to its better filtration performance.
- 1 February 2023
- Published by Thomas Telford Ltd. in Advances in Cement Research
- Vol. 35 (2) , 70-80
Experimental study of a self-expanding filling material for mine-sealing walls
A self-expanding filling material for mine-sealing walls (SEFM–MSW) was developed to solve the problems of large solid material amounts, high labour intensities and poor sealing effects. This study examines material composition and structure. The results are as follows. First, the SEFM–MSW could be optimised with an expansion agent at 0.4∼1.0%, an admixture at 1.0∼1.5%, a fibre at 0.1% and a w/c (water/cement) ratio of 0.45∼0.5. Second, the fitting results were highly consistent of the relationship between the 28d-compressive strength and the porosity of the SEFM–MSW with the Ryshkewitch and Balshin models. Third, when the SEFM–MSW expansion ratio was higher, the average pore size was larger, the pore size distribution was wider and the compressive strength was lower. These results have realistic impacts for practical engineering applications.
- 1 February 2023
- Published by Thomas Telford Ltd. in Advances in Cement Research
- Vol. 35 (2) , 70-80
Experimental study of a self-expanding filling material for mine-sealing walls
A self-expanding filling material for mine-sealing walls (SEFM–MSW) was developed to solve the problems of large solid material amounts, high labour intensities and poor sealing effects. This study examines material composition and structure. The results are as follows. First, the SEFM–MSW could be optimised with an expansion agent at 0.4∼1.0%, an admixture at 1.0∼1.5%, a fibre at 0.1% and a w/c (water/cement) ratio of 0.45∼0.5. Second, the fitting results were highly consistent of the relationship between the 28d-compressive strength and the porosity of the SEFM–MSW with the Ryshkewitch and Balshin models. Third, when the SEFM–MSW expansion ratio was higher, the average pore size was larger, the pore size distribution was wider and the compressive strength was lower. These results have realistic impacts for practical engineering applications.
- Open Access
- 25 November 2022
- Published by Springer Nature in Scientific Reports
- Vol. 12 (1) , 1-16
Influence of pleated geometry on the pressure drop of filters during dust loading process: experimental and modelling study
In this study, a pressure drop model was developed through numerical simulation and experimentation for optimizing the design of the pleated structure of the filter media to extend the service life of the filter and reduce the ventilation energy consumption. The effect of the Stokes number on the dust deposition on the pleated filter media was revealed through numerical simulation. On this basis, a pressure drop model during dust loading was developed. The model suggests that under the same mass of dust deposition per unit area (W), the greater the pleat ratio (α), the greater the dust cake thickness and the effective filtration velocity in the effective filtration area. In addition, for V-shaped and U-shaped filters, the relative mean deviations between experimental and modeling total pressure drops are 3.68% and 4.82%, respectively. In other words, the proposed model accurately predicts pressure drop during dust loading. Furthermore, under the same α and $$W$$ , the total pressure drop of the U-shaped filter is lower than that of the V-shaped filter, demonstrating the superior filtration performance of the U-shaped filter.- 25 November 2022
- Published by Springer Nature in Scientific Reports
- Vol. 12 (1) , 1-16
Open AccessInfluence of pleated geometry on the pressure drop of filters during dust loading process: experimental and modelling study
In this study, a pressure drop model was developed through numerical simulation and experimentation for optimizing the design of the pleated structure of the filter media to extend the service life of the filter and reduce the ventilation energy consumption. The effect of the Stokes number on the dust deposition on the pleated filter media was revealed through numerical simulation. On this basis, a pressure drop model during dust loading was developed. The model suggests that under the same mass of dust deposition per unit area (W), the greater the pleat ratio (α), the greater the dust cake thickness and the effective filtration velocity in the effective filtration area. In addition, for V-shaped and U-shaped filters, the relative mean deviations between experimental and modeling total pressure drops are 3.68% and 4.82%, respectively. In other words, the proposed model accurately predicts pressure drop during dust loading. Furthermore, under the same α and $$W$$ , the total pressure drop of the U-shaped filter is lower than that of the V-shaped filter, demonstrating the superior filtration performance of the U-shaped filter. - 1 January 2022
- Published by Elsevier in Advanced Powder Technology
- Vol. 33 (1) , 103352
Influence of coal properties on dust suppression effect of biological dust suppressant
- 1 January 2022
- Published by Elsevier in Advanced Powder Technology
- Vol. 33 (1) , 103352
Influence of coal properties on dust suppression effect of biological dust suppressant
- 1 June 2019
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 44 (30) , 15997-16003
Estimation of hydrogen release and conversion in coal-bed methane from roof extraction in mine goaf
- 1 June 2019
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 44 (30) , 15997-16003
Estimation of hydrogen release and conversion in coal-bed methane from roof extraction in mine goaf