Alexandra Klimenko
Alexandra Klimenko has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
Maurice Bourrel
Laboratoire Physico-Chimie des Interfaces Complexes, Bâtiment CHEMSTARTUP
5 shared publications- François Lequeux
Soft Matter Sciences and Engineering (SIMM), ESPCI Paris, PSL University, Sorbonne Université, CNRS, F-75005 Paris, France
4 shared publications - Pascal Panizza
Laboratoire Physico‐Chimie des Interfaces Complexes ESPCI Paris and TotalEnergies Lacq France
4 shared publications - Valérie Molinier
TotalEnergies OneTech, Pôle d''Etudes et de Recherche de Lacq (PERL) Lacq France
3 shared publications - Mattéo Clerget
TotalEnergies S.E., Pôle d’Etude et de Recherches de Lacq, BP 47 Lacq 64170, France
2 shared publications - Abdulmajeed Murad
Department of Chemistry, University of Bergen, 5007 Bergen, Norway
1 shared publication
Latest Publications
- 30 June 2026
- Published by Agence Bibliographique de l'Enseignement Supérieur
Rôle des agents amphiphiles dans les mécanismes de transport multiphasique en milieu poreux
Cette thèse analyse le rôle des agents amphiphiles dans le transport multiphasique en milieu poreux, dans le cadre de la récupération assistée du pétrole. Elle s’appuie sur dix années de travaux expérimentaux visant à comprendre et optimiser l’extraction du pétrole piégé dans les roches. Trois mécanismes majeurs sont étudiés : la réduction de la tension interfaciale, la modification de la mouillabilité et le contrôle de la mobilité des fluides. L’analyse des systèmes eau/huile/tensioactifs met en évidence l’importance des comportements de phase, en particulier des conditions de type Winsor III, associées à des tensions interfaciales ultra-faibles favorisant la mobilisation du pétrole. Les résultats montrent que les composés naturels du brut, tels que les acides naphténiques et les asphaltènes, jouent un rôle clé en tant que tensioactifs endogènes. Leur interaction avec les tensioactifs synthétiques influence fortement les propriétés interfaciales et l’efficacité des formulations. Le contrôle de la salinité et l’utilisation de gradients salins apparaissent essentiels pour maintenir des conditions optimales lors du transport en milieu poreux. La thèse met également en évidence les mécanismes de modification de la mouillabilité, notamment via l’adsorption interfaciale et la formation de microgouttelettes d’eau dans l’huile. Enfin, l’injection de mousses de CO₂ est étudiée pour améliorer le contrôle de mobilité et stabiliser les écoulements. L’ensemble propose une approche intégrée combinant physico chimie, hydrodynamique et formulation
- 30 June 2026
- Published by Agence Bibliographique de l'Enseignement Supérieur
Rôle des agents amphiphiles dans les mécanismes de transport multiphasique en milieu poreux
Cette thèse analyse le rôle des agents amphiphiles dans le transport multiphasique en milieu poreux, dans le cadre de la récupération assistée du pétrole. Elle s’appuie sur dix années de travaux expérimentaux visant à comprendre et optimiser l’extraction du pétrole piégé dans les roches. Trois mécanismes majeurs sont étudiés : la réduction de la tension interfaciale, la modification de la mouillabilité et le contrôle de la mobilité des fluides. L’analyse des systèmes eau/huile/tensioactifs met en évidence l’importance des comportements de phase, en particulier des conditions de type Winsor III, associées à des tensions interfaciales ultra-faibles favorisant la mobilisation du pétrole. Les résultats montrent que les composés naturels du brut, tels que les acides naphténiques et les asphaltènes, jouent un rôle clé en tant que tensioactifs endogènes. Leur interaction avec les tensioactifs synthétiques influence fortement les propriétés interfaciales et l’efficacité des formulations. Le contrôle de la salinité et l’utilisation de gradients salins apparaissent essentiels pour maintenir des conditions optimales lors du transport en milieu poreux. La thèse met également en évidence les mécanismes de modification de la mouillabilité, notamment via l’adsorption interfaciale et la formation de microgouttelettes d’eau dans l’huile. Enfin, l’injection de mousses de CO₂ est étudiée pour améliorer le contrôle de mobilité et stabiliser les écoulements. L’ensemble propose une approche intégrée combinant physico chimie, hydrodynamique et formulation
- Open Access
- 9 June 2026
- Published by National Academy of Sciences in Proceedings of the National Academy of Sciences
- Vol. 123 (24)
Tuning bubble coalescence rates over orders of magnitude in liquid mixtures of simple surface thermodynamics: Experiments and theory
The coalescence time of bubbles in a liquid depends on the nature of the liquid, which determines both its surface thermodynamics and the molecular interactions between the gas/liquid interfaces, and on the geometry, prescribed by the curvature of the bubbles. Coalescence is well described in pure liquids that have the same composition in bulk and at interfaces and in which the interactions are attractive. In contrast, the mechanisms are poorly understood in more complex liquids in which coalescence times are orders of magnitudes larger than in pure liquids and are unpredictable. To provide insight on these mechanisms, we use model systems: binary mixtures of miscible oils. In these liquids, interfaces have purely attractive molecular interactions and the surface thermodynamics can simply be described using a well-determined Gibbs elastic modulus, which is controlled by the composition of the mixture. We measure the coalescence rate by forming periodic trains of bubbles in millifluidic tubes whose radius varies over 1.5 decade. We report coalescence times spanning more than three decades and, for a given composition, varying according to a power law with curvature, with an exponent larger than that reported in pure liquids and independent of Gibbs elasticity. The experimental behavior is in excellent agreement with a numerical solution of the coupled thermodynamical and hydrodynamical equations, performed in the simple geometry of a suspended liquid film. Our results clearly reveal how geometry and surface thermodynamics modify the coalescence process of bubbles in the limit of small Gibbs elasticity.
- 9 June 2026
- Published by National Academy of Sciences in Proceedings of the National Academy of Sciences
- Vol. 123 (24)
Open AccessTuning bubble coalescence rates over orders of magnitude in liquid mixtures of simple surface thermodynamics: Experiments and theory
The coalescence time of bubbles in a liquid depends on the nature of the liquid, which determines both its surface thermodynamics and the molecular interactions between the gas/liquid interfaces, and on the geometry, prescribed by the curvature of the bubbles. Coalescence is well described in pure liquids that have the same composition in bulk and at interfaces and in which the interactions are attractive. In contrast, the mechanisms are poorly understood in more complex liquids in which coalescence times are orders of magnitudes larger than in pure liquids and are unpredictable. To provide insight on these mechanisms, we use model systems: binary mixtures of miscible oils. In these liquids, interfaces have purely attractive molecular interactions and the surface thermodynamics can simply be described using a well-determined Gibbs elastic modulus, which is controlled by the composition of the mixture. We measure the coalescence rate by forming periodic trains of bubbles in millifluidic tubes whose radius varies over 1.5 decade. We report coalescence times spanning more than three decades and, for a given composition, varying according to a power law with curvature, with an exponent larger than that reported in pure liquids and independent of Gibbs elasticity. The experimental behavior is in excellent agreement with a numerical solution of the coupled thermodynamical and hydrodynamical equations, performed in the simple geometry of a suspended liquid film. Our results clearly reveal how geometry and surface thermodynamics modify the coalescence process of bubbles in the limit of small Gibbs elasticity.
- Open Access
Impact of Adverse Mobility Ratio on Oil Mobilization by Polymer Flooding
Polymer flooding is a widely used enhanced oil recovery (EOR) method for improving energy efficiency and reducing the carbon footprint of oil production. Optimizing polymer concentration is critical for maximizing recovery while minimizing economic and environmental costs. Here, we present a systematic experimental study which shows that even very low concentrations of polymers yield relatively high recovery rates at adverse mobility ratios (230 cP oil). A series of core flood experiments were conducted on Bentheimer sandstone rock, with polymer concentrations ranging from 40 ppm (1.35 cP) to 600 ppm (10.0 cP). Beyond a mobility ratio threshold, increasing polymer concentration did not significantly enhance recovery. This plateau in performance was attributed to the persistence of viscous fingering and oil crossflow into pre-established water channels. The study suggests that low concentrations of polymer may mobilize oil at high mobility ratios by making use of the pre-established water channels as transport paths for the oil and that the rheology of the polymer enhances this effect. These findings enable reductions in the polymer concentration in fields with adverse mobility ratios, leading to substantial reductions in chemical usage, energy consumption, and environmental impact of the extraction process.
Open AccessImpact of Adverse Mobility Ratio on Oil Mobilization by Polymer Flooding
Polymer flooding is a widely used enhanced oil recovery (EOR) method for improving energy efficiency and reducing the carbon footprint of oil production. Optimizing polymer concentration is critical for maximizing recovery while minimizing economic and environmental costs. Here, we present a systematic experimental study which shows that even very low concentrations of polymers yield relatively high recovery rates at adverse mobility ratios (230 cP oil). A series of core flood experiments were conducted on Bentheimer sandstone rock, with polymer concentrations ranging from 40 ppm (1.35 cP) to 600 ppm (10.0 cP). Beyond a mobility ratio threshold, increasing polymer concentration did not significantly enhance recovery. This plateau in performance was attributed to the persistence of viscous fingering and oil crossflow into pre-established water channels. The study suggests that low concentrations of polymer may mobilize oil at high mobility ratios by making use of the pre-established water channels as transport paths for the oil and that the rheology of the polymer enhances this effect. These findings enable reductions in the polymer concentration in fields with adverse mobility ratios, leading to substantial reductions in chemical usage, energy consumption, and environmental impact of the extraction process.
- 11 June 2025
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 39 (25) , 12125-12138
Auto-Emulsification of Water at the Crude Oil/Water Interface: Role of the Solid Walls and Wettability Alteration
- 11 June 2025
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 39 (25) , 12125-12138
Auto-Emulsification of Water at the Crude Oil/Water Interface: Role of the Solid Walls and Wettability Alteration
- Open Access
- 20 August 2024
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 9 (35) , 37094-37104
CO2 Geostorage and Enhanced Oil Recovery: Challenges in Controlling Foam/Emulsion Generation and Propagation
CO2 injection in subterranean reservoirs for storage, oil recovery, or both is challenging because of its very high mobility. Using a CO2 foam or emulsion is a way to remedy this problem by increasing CO2's apparent viscosity. However, the generation of the foam and its propagation in porous media present several issues that have to be overcome for this process to be economically realistic in practice. For example, it may take time, i.e., a number of pore volumes to be injected, before the foam is created. It is the objective of this Article to investigate these issues thoroughly and to identify the mechanisms underlying them by looking at the effects of various parameters. It is found that surfactant adsorption on the surface of the rock is an important factor involved in the delay of foam formation, but this may not explain all of the results. The nature and morphology of the porous medium may be, in some cases, the dominant factors for foam generation and propagation. From an understanding of the origin of the encountered problem, relevant mitigation strategies are envisioned and evaluated. It is found, for example, that when appropriately formulated and injected with the proper process, foam or emulsion generation is strongly accelerated, which very significantly shortens the delay for achieving CO2 storage.
- 20 August 2024
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 9 (35) , 37094-37104
Open AccessCO2 Geostorage and Enhanced Oil Recovery: Challenges in Controlling Foam/Emulsion Generation and Propagation
CO2 injection in subterranean reservoirs for storage, oil recovery, or both is challenging because of its very high mobility. Using a CO2 foam or emulsion is a way to remedy this problem by increasing CO2's apparent viscosity. However, the generation of the foam and its propagation in porous media present several issues that have to be overcome for this process to be economically realistic in practice. For example, it may take time, i.e., a number of pore volumes to be injected, before the foam is created. It is the objective of this Article to investigate these issues thoroughly and to identify the mechanisms underlying them by looking at the effects of various parameters. It is found that surfactant adsorption on the surface of the rock is an important factor involved in the delay of foam formation, but this may not explain all of the results. The nature and morphology of the porous medium may be, in some cases, the dominant factors for foam generation and propagation. From an understanding of the origin of the encountered problem, relevant mitigation strategies are envisioned and evaluated. It is found, for example, that when appropriately formulated and injected with the proper process, foam or emulsion generation is strongly accelerated, which very significantly shortens the delay for achieving CO2 storage.
- Open Access
- 6 February 2024
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 9 (7) , 8320-8332
Foam Generation Through a Single Pore with Rectangular Cross-Section: Hysteretic Behavior and Geometric Limitation of the Volume Fraction of Bubbles
We study foam production and destabilization through a flow-focusing geometry, namely a single pore of rectangular cross-section, by coinjecting gas and liquid at constant pressure, Pg, and constant flow rate, Qw. We observe that bubble production results from a Rayleigh-Plateau destabilization of the internal gas thread that occurs at the pore neck when its width becomes comparable to the height of the rectangular-section channel. Using a simple model and numerical approach, we (i) predict the shape of the gas jet and its stability range as a function of flow parameters and device geometry, which we successfully compare with our experimental results, and (ii) demonstrate the existence of a critical local pressure drop at the pore neck that determines whether or not a stable gas flow can form. We thus show that bubble foam generation exhibits hysteretic behavior due to hydrodynamic feedback and demonstrate that there is a maximum bubble volume fraction that the generated foam cannot exceed, the value of which is fixed by the geometry. Our results suggest that the foam collapse observed in porous media when the fractional gas flow becomes too large may result from hydrodynamic feedback inhibiting foam generation and not necessarily from coalescence between bubbles, as is usually claimed.
- 6 February 2024
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 9 (7) , 8320-8332
Open AccessFoam Generation Through a Single Pore with Rectangular Cross-Section: Hysteretic Behavior and Geometric Limitation of the Volume Fraction of Bubbles
We study foam production and destabilization through a flow-focusing geometry, namely a single pore of rectangular cross-section, by coinjecting gas and liquid at constant pressure, Pg, and constant flow rate, Qw. We observe that bubble production results from a Rayleigh-Plateau destabilization of the internal gas thread that occurs at the pore neck when its width becomes comparable to the height of the rectangular-section channel. Using a simple model and numerical approach, we (i) predict the shape of the gas jet and its stability range as a function of flow parameters and device geometry, which we successfully compare with our experimental results, and (ii) demonstrate the existence of a critical local pressure drop at the pore neck that determines whether or not a stable gas flow can form. We thus show that bubble foam generation exhibits hysteretic behavior due to hydrodynamic feedback and demonstrate that there is a maximum bubble volume fraction that the generated foam cannot exceed, the value of which is fixed by the geometry. Our results suggest that the foam collapse observed in porous media when the fractional gas flow becomes too large may result from hydrodynamic feedback inhibiting foam generation and not necessarily from coalescence between bubbles, as is usually claimed.
- Open Access
- 3 February 2024
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 9 (6) , 6932-6944
Straightforward Assessment of Wettability Changes by Washburn Capillary Rise: Toward a Screening Tool for Selecting Water Compositions for Improved Oil Recovery
Evaluating the wettability state of reservoir rocks is key for understanding and optimizing waterflooding and improved oil recovery techniques that imply the use of low-salinity water. Aside from established petrophysical techniques, such as Amott imbibition tests, we evaluated the Washburn capillary rise method as a low-cost, easy-to-implement, and rapid screening tool for probing the wettability state of rock samples. The well-known limitations of this method are discussed and circumvented. We show that measuring the capillary rise of two liquids brine and n-octaneis required to assess the evolution of the wettability state of a material induced by various treatments. The wettability state is quantified by the adhesion tension of brine to the solid. The higher the adhesion tension of brine, the more water-wet the sample. An increase in oil-wetness is observed when the sample is contacted with a crude oil or its released waters; an increase in water-wetness is obtained by postcontacting the oil-wet sample with low-salinity brine or surfactant solutions. The Washburn capillary rise is revealed to be a robust method for screening wettability alteration. With a typical duration of 1–10 min, it allows reproducibility check and screening of a wide range of brine compositions in a reasonable time frame. Therefore, it is a relevant tool to identify the most favorable brine compositions to be tested afterward with more time-consuming techniques, such as Amott tests and corefloods.
- 3 February 2024
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 9 (6) , 6932-6944
Open AccessStraightforward Assessment of Wettability Changes by Washburn Capillary Rise: Toward a Screening Tool for Selecting Water Compositions for Improved Oil Recovery
Evaluating the wettability state of reservoir rocks is key for understanding and optimizing waterflooding and improved oil recovery techniques that imply the use of low-salinity water. Aside from established petrophysical techniques, such as Amott imbibition tests, we evaluated the Washburn capillary rise method as a low-cost, easy-to-implement, and rapid screening tool for probing the wettability state of rock samples. The well-known limitations of this method are discussed and circumvented. We show that measuring the capillary rise of two liquids brine and n-octaneis required to assess the evolution of the wettability state of a material induced by various treatments. The wettability state is quantified by the adhesion tension of brine to the solid. The higher the adhesion tension of brine, the more water-wet the sample. An increase in oil-wetness is observed when the sample is contacted with a crude oil or its released waters; an increase in water-wetness is obtained by postcontacting the oil-wet sample with low-salinity brine or surfactant solutions. The Washburn capillary rise is revealed to be a robust method for screening wettability alteration. With a typical duration of 1–10 min, it allows reproducibility check and screening of a wide range of brine compositions in a reasonable time frame. Therefore, it is a relevant tool to identify the most favorable brine compositions to be tested afterward with more time-consuming techniques, such as Amott tests and corefloods.
- 1 April 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (4)
Marangoni destabilization of bidimensional-confined gas–liquid co-flowing streams in rectangular microfluidic channels
In microchannels, the stability of a fluid jet injected into another immiscible fluid strongly depends on its degree of geometric confinement. When the width of the jet, w, is larger than the channel height, H, the surface tension driven Rayleigh–Plateau instability is suppressed so that the 2D (bidimensional)-confined jet is absolutely stable and never collapses into bubbles (or drops) in contrast to what occurs when w ≤ H [Dollet et al., “Role of the channel geometry on the bubble pinch-off in flow-focusing,” Phys. Rev. Lett. 100(3), 034504 (2008); Guillot et al., “Stability of a jet in confined pressure-driven biphasic flows at low Reynolds number in various geometries,” Phys. Rev. E 78(1), 016307 (2008)]. We here demonstrate both experimentally and theoretically that this picture is, indeed, no longer valid when Marangoni effects are considered. We experimentally show that the addition of small length alcohol molecules into the liquid phase destabilizes a 2D-confined gas–water microfluidic stream ( w > H), leading to the generation of steady non-linear waves and further to the production of bubbles. Using a simple hydrodynamic model, we show through a linear analysis that the destabilization of the gas stream may result from a Marangoni instability due to the fast adsorption of the alcohol molecules, which occurs on a timescale comparable to that of the microfluidic flow.
- 1 April 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (4)
Marangoni destabilization of bidimensional-confined gas–liquid co-flowing streams in rectangular microfluidic channels
In microchannels, the stability of a fluid jet injected into another immiscible fluid strongly depends on its degree of geometric confinement. When the width of the jet, w, is larger than the channel height, H, the surface tension driven Rayleigh–Plateau instability is suppressed so that the 2D (bidimensional)-confined jet is absolutely stable and never collapses into bubbles (or drops) in contrast to what occurs when w ≤ H [Dollet et al., “Role of the channel geometry on the bubble pinch-off in flow-focusing,” Phys. Rev. Lett. 100(3), 034504 (2008); Guillot et al., “Stability of a jet in confined pressure-driven biphasic flows at low Reynolds number in various geometries,” Phys. Rev. E 78(1), 016307 (2008)]. We here demonstrate both experimentally and theoretically that this picture is, indeed, no longer valid when Marangoni effects are considered. We experimentally show that the addition of small length alcohol molecules into the liquid phase destabilizes a 2D-confined gas–water microfluidic stream ( w > H), leading to the generation of steady non-linear waves and further to the production of bubbles. Using a simple hydrodynamic model, we show through a linear analysis that the destabilization of the gas stream may result from a Marangoni instability due to the fast adsorption of the alcohol molecules, which occurs on a timescale comparable to that of the microfluidic flow.
- 21 January 2022
- Published by Elsevier in Journal of Petroleum Science and Engineering
- Vol. 211, 110190
Effect of surfactants at ultra-low concentration in oil/brine diphasic displacement: The way to unlock EOR polymer field projects
- 21 January 2022
- Published by Elsevier in Journal of Petroleum Science and Engineering
- Vol. 211, 110190
Effect of surfactants at ultra-low concentration in oil/brine diphasic displacement: The way to unlock EOR polymer field projects
- 23 November 2021
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 35 (24) , 20046-20059
Insights into the Intimate Link between the Surfactant/Oil/Water Phase Behavior and the Successful Design of (Alkali)–Surfactant–Polymer Floods
- 23 November 2021
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 35 (24) , 20046-20059
Insights into the Intimate Link between the Surfactant/Oil/Water Phase Behavior and the Successful Design of (Alkali)–Surfactant–Polymer Floods