Jeehwan Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jeehwan Kim has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Hui-Suk Yun
Korea Institute of Materials Science (KIMS), Changwon, Republic of Korea,; University of Science and Technology (UST), Daejeon, Republic of Korea
4 shared publications Chang Woo Gal
3 shared publications- Yeong-Jin Choi
Advanced Bio and Healthcare Materials Research Division, Korea Institute of Materials Science (KIMS), Changwon, Republic of Korea
3 shared publications Honghyun Park
Department of Advanced Biomaterials Research Ceramics Materials Division Korea Institute of Materials Science Changwon South Korea
2 shared publicationsImam Akbar Sutejo
Korea Institute of Materials Science (KIMS), Changwon, Republic of Korea,; University of Science and Technology (UST), Daejeon, Republic of Korea
2 shared publications- Seog-Young Yoon
School of Materials Science and Engineering, Pusan National University, Materials Building, 2, Busandaehak-ro 63beon-gil, Geumjeong-gu, Busan 46241, Republic of Korea
2 shared publications
Latest Publications
- Open Access
- 17 January 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (8) , 10318-10327
Fabrication and characterisation of Al2O3–ZrO2 functionally graded ceramics via DLP-based additive manufacturing
- 17 January 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (8) , 10318-10327
Open AccessFabrication and characterisation of Al2O3–ZrO2 functionally graded ceramics via DLP-based additive manufacturing
- Open Access
- 21 April 2023
- Published by Elsevier in Dental Materials
- Vol. 39 (6) , 568-576
Fabrication of color-graded feldspathic dental prosthetics for aesthetic and restorative dentistry
- 21 April 2023
- Published by Elsevier in Dental Materials
- Vol. 39 (6) , 568-576
Open AccessFabrication of color-graded feldspathic dental prosthetics for aesthetic and restorative dentistry
- Open Access
- 29 January 2022
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 105 (6) , 3827-3837
Three‐dimensional complex construct fabrication of illite by digital light processing‐based additive manufacturing technology
Illite is a group of clay minerals that are expected to be widely used in catalyst fabrication, radioactive element adsorption, and so forth, due to its excellent adsorption properties. However, the shape control limitation of the illite product should be overcome to maximize its utilization and properties. We herein propose additive manufacturing (AM) as one of the best solutions to solve this structural drawback. Digital light processing (DLP) technology with the film‐type of the material supplying system was adapted instead of the general vat‐type DLP system to increase illite printability. The photo‐curability and printability of illite‐contained photocurable suspension were optimized. The color effect due to different ferric oxide content in yellow‐ and white‐illite which influence the photopolymerization process also adjusted thoroughly. White illite showed better photo‐curability and could be increased solid loading than yellow illite. The defect‐free illite products with three‐dimensional complex structures, which cannot be produced by typical ceramic processes, were obtained by DLP technology for both yellow‐ and white‐illite after sintering at 1100°C. The overcoming of shape control limitation of illites by ceramic AM proved in this study has excellent potential for expanding illite utilities in various applications.
- 29 January 2022
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 105 (6) , 3827-3837
Open AccessThree‐dimensional complex construct fabrication of illite by digital light processing‐based additive manufacturing technology
Illite is a group of clay minerals that are expected to be widely used in catalyst fabrication, radioactive element adsorption, and so forth, due to its excellent adsorption properties. However, the shape control limitation of the illite product should be overcome to maximize its utilization and properties. We herein propose additive manufacturing (AM) as one of the best solutions to solve this structural drawback. Digital light processing (DLP) technology with the film‐type of the material supplying system was adapted instead of the general vat‐type DLP system to increase illite printability. The photo‐curability and printability of illite‐contained photocurable suspension were optimized. The color effect due to different ferric oxide content in yellow‐ and white‐illite which influence the photopolymerization process also adjusted thoroughly. White illite showed better photo‐curability and could be increased solid loading than yellow illite. The defect‐free illite products with three‐dimensional complex structures, which cannot be produced by typical ceramic processes, were obtained by DLP technology for both yellow‐ and white‐illite after sintering at 1100°C. The overcoming of shape control limitation of illites by ceramic AM proved in this study has excellent potential for expanding illite utilities in various applications.
- Open Access
- 23 November 2021
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 19 (2) , 968-978
Effect of dispersants on structural integrity of 3D printed ceramics
Ceramic 3D printing based on stereolithography is an excellent alternative to overcome drawbacks of conventional subtractive manufacturing for 3D shape control. Optimization of photocurable ceramic slurry is one of the most essential conditions to achieve favorable 3D printed structures using SL. Homogeneity of ceramic particle dispersion in photocurable resin is particularly important to optimize ceramic suspension. Dispersant plays a significant role in increasing homogeneity. Dispersant in photocurable ceramic resin has an additional effect on photocurability and integrity of 3D printed green body. We herein discuss how dispersants influence 3D printing conditions based on stereolithography using various commercially available dispersants of BYK series such as BYK103, BYK111, BYK180, BYK182, and BYK2001. Both BYK111 and BYK180 showed better performances than others because of their lower volatilities under general temperature condition during a printing process. Both solubility and decomposition temperature of dispersants largely influenced the structural quality after washing and debinding processes. This study provides worthy information to design photocurable ceramic suspension for various types of ceramic materials.
- 23 November 2021
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 19 (2) , 968-978
Open AccessEffect of dispersants on structural integrity of 3D printed ceramics
Ceramic 3D printing based on stereolithography is an excellent alternative to overcome drawbacks of conventional subtractive manufacturing for 3D shape control. Optimization of photocurable ceramic slurry is one of the most essential conditions to achieve favorable 3D printed structures using SL. Homogeneity of ceramic particle dispersion in photocurable resin is particularly important to optimize ceramic suspension. Dispersant plays a significant role in increasing homogeneity. Dispersant in photocurable ceramic resin has an additional effect on photocurability and integrity of 3D printed green body. We herein discuss how dispersants influence 3D printing conditions based on stereolithography using various commercially available dispersants of BYK series such as BYK103, BYK111, BYK180, BYK182, and BYK2001. Both BYK111 and BYK180 showed better performances than others because of their lower volatilities under general temperature condition during a printing process. Both solubility and decomposition temperature of dispersants largely influenced the structural quality after washing and debinding processes. This study provides worthy information to design photocurable ceramic suspension for various types of ceramic materials.