Adel Tayeb
Research Subjects
Adel Tayeb has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Jean-Benoît Le Cam
Université de Rennes, Institut de Physique de Rennes, UMR 6251 CNRS, Rennes, France
4 shared publications - Abdelmalek Zine
Institut Camille Jordan, Ecole Centrale de Lyon, 69134 Ecully, France
1 shared publication - Adel Hamdi
Applied Mechanics and Engineering Laboratory (LMAI), National Engineering School of Tunis (ENIT), University of Tunis El Manar, Belvédère, Tunis, Tunisia
1 shared publication Allan Harte
Culham Campus, UKAEA, Abingdon, UK
1 shared publicationBruno Loez
1 shared publicationCory Hamelin
Culham Campus, UKAEA, Abingdon, UK
1 shared publication
Latest Publications
- Open Access
- 15 April 2026
- Published by SAGE Publications in The Journal of Strain Analysis for Engineering Design
- Vol. 61 (4) , 267-283
Image-based deformation measurements of fusion divertor armour under high heat flux loading
Engineering components within a fusion reactor are subjected to extreme environments including high heat flux, strong magnetic fields and neutron irradiation. Simulations are required to predict the in-service lifetimes of fusion components and ensuring credibility of these simulations requires validation over testable domains. Divertors are responsible for extracting heat and ash from the fusion reaction and protecting the vacuum vessel from thermal loads. In this work, we conduct an image-based experimental assessment of a divertor armour component design under a steady-state, high heat flux of ~ 5 MW / m 2 under vacuum conditions. The heat flux was applied to the water-cooled component using the Heating by Induction to Verify Extremes (HIVE) facility at the UK Atomic Energy Authority. We used digital image correlation (DIC) to measure the surface strain of the component and thermocouples to measure the temperature during the high heat flux pulse. We used synthetic image deformation simulations to analyse sources of random and systematic errors in our DIC measurements and to select DIC processing parameters for subsequent analysis. Our results show that DIC is a valuable tool for the validation of multi-physics simulations by providing information about the geometrical arrangement of components as well as high resolution data indicating areas of disagreement between the simulation and experiment. The results of our study are the first image-based simulation validation dataset for a divertor component under fusion relevant conditions.
- 15 April 2026
- Published by SAGE Publications in The Journal of Strain Analysis for Engineering Design
- Vol. 61 (4) , 267-283
Open AccessImage-based deformation measurements of fusion divertor armour under high heat flux loading
Engineering components within a fusion reactor are subjected to extreme environments including high heat flux, strong magnetic fields and neutron irradiation. Simulations are required to predict the in-service lifetimes of fusion components and ensuring credibility of these simulations requires validation over testable domains. Divertors are responsible for extracting heat and ash from the fusion reaction and protecting the vacuum vessel from thermal loads. In this work, we conduct an image-based experimental assessment of a divertor armour component design under a steady-state, high heat flux of ~ 5 MW / m 2 under vacuum conditions. The heat flux was applied to the water-cooled component using the Heating by Induction to Verify Extremes (HIVE) facility at the UK Atomic Energy Authority. We used digital image correlation (DIC) to measure the surface strain of the component and thermocouples to measure the temperature during the high heat flux pulse. We used synthetic image deformation simulations to analyse sources of random and systematic errors in our DIC measurements and to select DIC processing parameters for subsequent analysis. Our results show that DIC is a valuable tool for the validation of multi-physics simulations by providing information about the geometrical arrangement of components as well as high resolution data indicating areas of disagreement between the simulation and experiment. The results of our study are the first image-based simulation validation dataset for a divertor component under fusion relevant conditions.
- 6 April 2026
- Published by Agence Bibliographique de l'Enseignement Supérieur
Contribution to the modelling of the viscoelastic behavior of elastomers with Payne effect
Contribution à la modélisation du comportement viscoélastique des élastomères: Pas de résumé
- 6 April 2026
- Published by Agence Bibliographique de l'Enseignement Supérieur
Contribution to the modelling of the viscoelastic behavior of elastomers with Payne effect
Contribution à la modélisation du comportement viscoélastique des élastomères: Pas de résumé
- Open Access
- 19 January 2024
- Published by Elsevier in Polymer Testing
- Vol. 131
Strain-induced crystallisation of reinforced elastomers using surface calorimetry
- 19 January 2024
- Published by Elsevier in Polymer Testing
- Vol. 131
Open AccessStrain-induced crystallisation of reinforced elastomers using surface calorimetry
- 13 September 2023
- Published by Springer Nature in Meccanica
- Vol. 58 (10) , 1983-2002
Identifying simultaneously hyper-viscoelastic parameters from a unique heterogenous relaxation test: application to engineering elastomeric materials
- 13 September 2023
- Published by Springer Nature in Meccanica
- Vol. 58 (10) , 1983-2002
Identifying simultaneously hyper-viscoelastic parameters from a unique heterogenous relaxation test: application to engineering elastomeric materials
- 3 May 2022
- Published by Springer Nature in The European Physical Journal Plus
- Vol. 137 (5) , 1-18
Investigation of the nonlinear hyper-viscoelastic behavior of elastomers at finite strain: implementation and numerical validation
- 3 May 2022
- Published by Springer Nature in The European Physical Journal Plus
- Vol. 137 (5) , 1-18
Investigation of the nonlinear hyper-viscoelastic behavior of elastomers at finite strain: implementation and numerical validation
- 1 February 2022
- Published by Elsevier in Mechanics of Materials
- Vol. 165
3D printing of soft thermoplastic elastomers: Effect of the deposit angle on mechanical and thermo-mechanical properties
- 1 February 2022
- Published by Elsevier in Mechanics of Materials
- Vol. 165
3D printing of soft thermoplastic elastomers: Effect of the deposit angle on mechanical and thermo-mechanical properties
- Open Access
Identifying hyperelastic constitutive parameters with sensitivity‐based virtual fields
This work deals with the identification of hyperelastic constitutive parameters using the virtual fields method. The choice of the virtual displacement fields is a crucial aspect of the method, typically for reducing the sensitivity to the measurement noise. A first and simple option is to generate the virtual displacement fields randomly. Nevertheless, in case of hyperelastic models for which the stress is not a linear function of the constitutive parameters, improving the choice of the virtual displacement fields is not trivial and an alternative strategy has to be found. In the present study, the sensitivity‐based virtual fields approach is applied and compared with the randomly generated virtual displacement fields approach. Two material models were considered: the Mooney model, which describes quite well the behavior of hyperelastic materials for small and moderate strains, and the Ogden model, which accounts for the stress hardening phenomenon observed at higher strains. The full kinematic fields are measured by using the digital image correlation technique during an equibiaxial tensile test performed on a cruciform specimen. Identification results are discussed through their capability to predict the external force measured during the test. The sensitivity‐based virtual fields approach is found to improve significantly the prediction compared with the randomly generated virtual displacement fields approach.
Open AccessIdentifying hyperelastic constitutive parameters with sensitivity‐based virtual fields
This work deals with the identification of hyperelastic constitutive parameters using the virtual fields method. The choice of the virtual displacement fields is a crucial aspect of the method, typically for reducing the sensitivity to the measurement noise. A first and simple option is to generate the virtual displacement fields randomly. Nevertheless, in case of hyperelastic models for which the stress is not a linear function of the constitutive parameters, improving the choice of the virtual displacement fields is not trivial and an alternative strategy has to be found. In the present study, the sensitivity‐based virtual fields approach is applied and compared with the randomly generated virtual displacement fields approach. Two material models were considered: the Mooney model, which describes quite well the behavior of hyperelastic materials for small and moderate strains, and the Ogden model, which accounts for the stress hardening phenomenon observed at higher strains. The full kinematic fields are measured by using the digital image correlation technique during an equibiaxial tensile test performed on a cruciform specimen. Identification results are discussed through their capability to predict the external force measured during the test. The sensitivity‐based virtual fields approach is found to improve significantly the prediction compared with the randomly generated virtual displacement fields approach.