Sergey N. Krivtsov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sergey N. Krivtsov has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Tatiana I. Krivtsova
Irkutsk National Research Technical University
3 shared publications T I Krivtsova
Iirkutsk National Research Technical University, 83, Lermontova ave., Irkutsk, 664074, Russia
2 shared publicationsA S Grebennikov
Yuri Gagarin State Technical University of Saratov, 77, Politechnicheskaya Street, Saratov, 410054, Russia
1 shared publicationA S Potapov
Automobile Transport Department, Irkutsk National Research Technical University, 83, Lermontov Street, 664074, Irkutsk, Russia
1 shared publication- A. I. Fedotov
Irkutsk National Research Technical University
1 shared publication - Alexey K. Bychkov
Irkutsk State National Research Technical University
1 shared publication
Latest Publications
- 11 July 2026
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 23 (3)
Analytical assessment of the difference in air flow rates as a diagnostic parameter of the cylinder-piston group of diesel engines
Introduction . Diesel engines remain the primary powertrain for trucks and special-purpose vehicles and their widespread replacement by electric traction is unlikely in the near future. Under these conditions, monitoring the technical condition of the engine, particularly the cylinder-piston group, whose service life determines the longevity of the powertrain, is a pressing issue. The cylinder-piston group wear during operation leads to a deterioration in the engine key performance indicators. Despite the availability of various diagnostic methods, most are labor-intensive or of limited practical value. The most reliable methods require the use of external diagnostic tools, while onboard self-diagnostic systems provide only indirect assessment of engine condition. Therefore, it is advisable to develop methods for estimating engine wear using parameters available for onboard monitoring, such as crankcase gas flow rate. Materials and Methods. The study of the dependance of crankcase gas flow with increase of the clearance in the piston ring on cylinder diameter has been conducted by mathematical method. Various diesel engine models for passenger cars and commercial vehicles have been used in the research. Diesel engines with various characteristics have been selected for examination, including cylinder diameters ranging from 83 to 144 mm and engine capacity from 2 to 16.0 liters. Regression analysis methods in the MATLAB software environment have been applied to process the data, resulting in the determination of patterns of crankcase gas flow rate changes due to cylinder leaks and a proportional value – the difference in airflow rates with a closed crankcase ventilation system and with the crankcase breather isolated from the intake tract. The validation of the model has additionally been conducted by comparing the calculated data with experimental measurements in laboratory and in field conditions. Discussion and Conclusion. The pattern obtained through the study allows us to determine the wear degree of the cylinder-piston group based on the air flow rate measured by standard on-board diagnostics. Measurements have been conducted with the forced crankcase ventilation hose connected and with this hose isolated from the measurement tract under identical conditions. The scientific contribution of this study lies in the experimental substantiation of a quantitative relationship between the difference in air flow in two measurement modes (with the crankcase ventilation hose connected and isolated) and the degree of cylinder-piston group wear. This relationship has not previously been presented in the literature as a clear diagnostic pattern suitable for use with standard sensors. It has been established that measuring the difference in air flow is a reliable indicator of cylinder-piston group wear, allowing to predict the engine condition without the use of invasive diagnostic methods. In conclusion, the study highlights the importance of regular monitoring the cylinder-piston group condition to maintain optimal performance and extend engine service life. Further work is recommended to focus on integrating the proposed methodology into on-board diagnostic systems.
- 11 July 2026
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 23 (3)
Analytical assessment of the difference in air flow rates as a diagnostic parameter of the cylinder-piston group of diesel engines
Introduction . Diesel engines remain the primary powertrain for trucks and special-purpose vehicles and their widespread replacement by electric traction is unlikely in the near future. Under these conditions, monitoring the technical condition of the engine, particularly the cylinder-piston group, whose service life determines the longevity of the powertrain, is a pressing issue. The cylinder-piston group wear during operation leads to a deterioration in the engine key performance indicators. Despite the availability of various diagnostic methods, most are labor-intensive or of limited practical value. The most reliable methods require the use of external diagnostic tools, while onboard self-diagnostic systems provide only indirect assessment of engine condition. Therefore, it is advisable to develop methods for estimating engine wear using parameters available for onboard monitoring, such as crankcase gas flow rate. Materials and Methods. The study of the dependance of crankcase gas flow with increase of the clearance in the piston ring on cylinder diameter has been conducted by mathematical method. Various diesel engine models for passenger cars and commercial vehicles have been used in the research. Diesel engines with various characteristics have been selected for examination, including cylinder diameters ranging from 83 to 144 mm and engine capacity from 2 to 16.0 liters. Regression analysis methods in the MATLAB software environment have been applied to process the data, resulting in the determination of patterns of crankcase gas flow rate changes due to cylinder leaks and a proportional value – the difference in airflow rates with a closed crankcase ventilation system and with the crankcase breather isolated from the intake tract. The validation of the model has additionally been conducted by comparing the calculated data with experimental measurements in laboratory and in field conditions. Discussion and Conclusion. The pattern obtained through the study allows us to determine the wear degree of the cylinder-piston group based on the air flow rate measured by standard on-board diagnostics. Measurements have been conducted with the forced crankcase ventilation hose connected and with this hose isolated from the measurement tract under identical conditions. The scientific contribution of this study lies in the experimental substantiation of a quantitative relationship between the difference in air flow in two measurement modes (with the crankcase ventilation hose connected and isolated) and the degree of cylinder-piston group wear. This relationship has not previously been presented in the literature as a clear diagnostic pattern suitable for use with standard sensors. It has been established that measuring the difference in air flow is a reliable indicator of cylinder-piston group wear, allowing to predict the engine condition without the use of invasive diagnostic methods. In conclusion, the study highlights the importance of regular monitoring the cylinder-piston group condition to maintain optimal performance and extend engine service life. Further work is recommended to focus on integrating the proposed methodology into on-board diagnostic systems.
- Open Access
- 3 April 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (7) , 3487
Improving the Environmental Safety of Transport Equipment Using Biodiesel Produced from Waste Vegetable
Issues related to the environmental safety of transport vehicles, the operation of which leads to environmental pollution, continue to be highly relevant. In this work, we consider the use of biofuel mixed with diesel fuel for internal combustion engines operating at low temperatures. This approach does not reduce the efficiency of transport, while also solving the issue of organic waste recycling. In this work, we address the possibility of reducing environmental pollution using carbon-neutral blended fuels based on esters of waste cooking oil (WCO), biobutanol, and diesel fuel for transport, tractor, and other equipment powered by a diesel internal combustion engine. In terms of the rate of biofuel implementation, Russia is still lagging behind the EU, China, and Japan, largely due to, inter alia, its climatic conditions with cold and long winters. The article also provides data on the possibility of using mixed biofuels under sub-zero temperatures. The process of forming a volumetric fuel supply through the common rail injector of the D4CB engine under changes in fuel pressure and drive pulse duration was also investigated, with the corresponding regression dependencies being presented. The losses of heat supplied into the cylinder when using a blend of diesel fuel and biodiesel (with 20 wt% butanol) in comparison with diesel fuel were analytically calculated. This made it possible to identify a function for adjusting fuel supply to compensate for power losses. The lubricity of fuel blends was assessed using the HFRR method.
- 3 April 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (7) , 3487
Open AccessImproving the Environmental Safety of Transport Equipment Using Biodiesel Produced from Waste Vegetable
Issues related to the environmental safety of transport vehicles, the operation of which leads to environmental pollution, continue to be highly relevant. In this work, we consider the use of biofuel mixed with diesel fuel for internal combustion engines operating at low temperatures. This approach does not reduce the efficiency of transport, while also solving the issue of organic waste recycling. In this work, we address the possibility of reducing environmental pollution using carbon-neutral blended fuels based on esters of waste cooking oil (WCO), biobutanol, and diesel fuel for transport, tractor, and other equipment powered by a diesel internal combustion engine. In terms of the rate of biofuel implementation, Russia is still lagging behind the EU, China, and Japan, largely due to, inter alia, its climatic conditions with cold and long winters. The article also provides data on the possibility of using mixed biofuels under sub-zero temperatures. The process of forming a volumetric fuel supply through the common rail injector of the D4CB engine under changes in fuel pressure and drive pulse duration was also investigated, with the corresponding regression dependencies being presented. The losses of heat supplied into the cylinder when using a blend of diesel fuel and biodiesel (with 20 wt% butanol) in comparison with diesel fuel were analytically calculated. This made it possible to identify a function for adjusting fuel supply to compensate for power losses. The lubricity of fuel blends was assessed using the HFRR method.
- Open Access
- 4 March 2025
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 22 (1) , 102-111
Premature engine failures of KamAZ vehicles with common rail fuel supply system in real operation
Introduction. For the manufacturer and consumer enterprises of the products, it is of interest to know the real operational reliability of power units of KamAZ vehicles, their weakest points, the causes of premature failures, as well as methods for identifying and preventing their occurrence, and therefore carry out scientific research aimed at solving the above task is relevant and timely.Methods. The study of the reliability of systems, components and assemblies of engines of KamAZ vehicles was carried out in the conditions of the official dealership center “Technical center Severny” (Irkutsk), specializing in the sale, maintenance and repair of KamAZ vehicles during 2020–2024. the study involved KamAZ vehicles with 740 engine, including those under warranty. The automobiles with these power units were operated primarily in the Irkutsk region, including server regions. at the same time, each work order recorded the reason for contacting the service, the mileage of the car, as well as the types of work performed. An important step was to identify the distribution law of the most frequent failures of engine systems and components.Discussion and conclusion. The analysis of the data obtained during the study indicates the predominance of two types of premature failures – cylinder heads, as well as fuel supply systems, primarily electrohydraulic injectors. It was found that premature failures of cylinder head and electrohydraulic injectors obey the Weibull distribution law and have mathematical expectations of a failure time of 49.6 thousand km for injectors and 41.9 thousand km for cylinder heads. At the same time, the failures of the cylinder head of the highly accelerated engines of the KamAZ-740.7 family (with a capacity of over 360 hp) are caused by increased thermal stress and can be classified as structural and operational.
- 4 March 2025
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 22 (1) , 102-111
Open AccessPremature engine failures of KamAZ vehicles with common rail fuel supply system in real operation
Introduction. For the manufacturer and consumer enterprises of the products, it is of interest to know the real operational reliability of power units of KamAZ vehicles, their weakest points, the causes of premature failures, as well as methods for identifying and preventing their occurrence, and therefore carry out scientific research aimed at solving the above task is relevant and timely.Methods. The study of the reliability of systems, components and assemblies of engines of KamAZ vehicles was carried out in the conditions of the official dealership center “Technical center Severny” (Irkutsk), specializing in the sale, maintenance and repair of KamAZ vehicles during 2020–2024. the study involved KamAZ vehicles with 740 engine, including those under warranty. The automobiles with these power units were operated primarily in the Irkutsk region, including server regions. at the same time, each work order recorded the reason for contacting the service, the mileage of the car, as well as the types of work performed. An important step was to identify the distribution law of the most frequent failures of engine systems and components.Discussion and conclusion. The analysis of the data obtained during the study indicates the predominance of two types of premature failures – cylinder heads, as well as fuel supply systems, primarily electrohydraulic injectors. It was found that premature failures of cylinder head and electrohydraulic injectors obey the Weibull distribution law and have mathematical expectations of a failure time of 49.6 thousand km for injectors and 41.9 thousand km for cylinder heads. At the same time, the failures of the cylinder head of the highly accelerated engines of the KamAZ-740.7 family (with a capacity of over 360 hp) are caused by increased thermal stress and can be classified as structural and operational.
- Open Access
- 1 January 2025
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 21 (6) , 900-913
Investigation of traction and dynamic properties of wheeled vehicles with electric and hybrid power plants on the test stands with running drums
Introduction. Modern wheeled vehicles with electric and hybrid power plants are becoming more and more widespread. It is obvious that with the increasing number of wheeled vehicles with electric and hybrid power plants, there is a need to conduct a full-fledged and qualitative study of the working processes of wheeled vehicles both at the stages of production and fine-tuning at manufacturing enterprises, and in operating conditions at the service stations and other organizations. The research of the technical condition of a wheeled vehicle with electric and hybrid power plants with a classic layout of the power unit and transmission (front or rear axle drive) is quite possible to be conducted on existing stands. But when testing wheeled vehicles with electric and hybrid power plants with all-wheel drive or with an electric motor generator for each drive wheel, a problem arises due to the lack of methods and means to measure traction force on each wheel individually.Materials and methods. This section provides an analysis of the possibilities of conducting a study of the technical condition of wheeled vehicles with electric and hybrid power plants on modern power and inertia stands that apply the principle of reversibility of motion.Results. Methods have been developed to study the traction and dynamic properties of wheeled vehicles with electric and hybrid power plants, to implement it was proposed to use developed research stand complex, which includes a hybrid stand with control and measuring systems that allow to determine forces and power on the driving wheels of vehicles, as well as time and kinematic parameters of its functioning process. During the experimental studies, the results of Kia Soul EV and Toyota Prius NHW20 operation processes were obtained, their power and kinematic parameters were analyzed.Conclusion. As a result of the study, it has been proved that in order to ensure highly informative and stable test modes of wheeled vehicle’s operation in the process of studying their traction and dynamic properties, it is necessary to use hybrid stands.
- 1 January 2025
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 21 (6) , 900-913
Open AccessInvestigation of traction and dynamic properties of wheeled vehicles with electric and hybrid power plants on the test stands with running drums
Introduction. Modern wheeled vehicles with electric and hybrid power plants are becoming more and more widespread. It is obvious that with the increasing number of wheeled vehicles with electric and hybrid power plants, there is a need to conduct a full-fledged and qualitative study of the working processes of wheeled vehicles both at the stages of production and fine-tuning at manufacturing enterprises, and in operating conditions at the service stations and other organizations. The research of the technical condition of a wheeled vehicle with electric and hybrid power plants with a classic layout of the power unit and transmission (front or rear axle drive) is quite possible to be conducted on existing stands. But when testing wheeled vehicles with electric and hybrid power plants with all-wheel drive or with an electric motor generator for each drive wheel, a problem arises due to the lack of methods and means to measure traction force on each wheel individually.Materials and methods. This section provides an analysis of the possibilities of conducting a study of the technical condition of wheeled vehicles with electric and hybrid power plants on modern power and inertia stands that apply the principle of reversibility of motion.Results. Methods have been developed to study the traction and dynamic properties of wheeled vehicles with electric and hybrid power plants, to implement it was proposed to use developed research stand complex, which includes a hybrid stand with control and measuring systems that allow to determine forces and power on the driving wheels of vehicles, as well as time and kinematic parameters of its functioning process. During the experimental studies, the results of Kia Soul EV and Toyota Prius NHW20 operation processes were obtained, their power and kinematic parameters were analyzed.Conclusion. As a result of the study, it has been proved that in order to ensure highly informative and stable test modes of wheeled vehicle’s operation in the process of studying their traction and dynamic properties, it is necessary to use hybrid stands.
- Open Access
- 12 March 2024
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 21 (1) , 98-107
Evaluation of reliability indicators of shock absorbers struts of M1 category cars in conditions of violation of established market relations between end users of spare parts and suppliers
Introduction. Over the past two years, there has been a violation of established market relations between end users of spare parts and suppliers. This led, on the one hand, to a significant increase in the cost of automotive components, and, on the other, to a reorientation of the market to new alternative manufacturers and suppliers. The main purpose of the work was a statistical assessment of the reliability indicators of the most expensive suspension element – the McPherson suspension strut, in the conditions of replacing the original struts with analogues available on the market.Methods. The study of the operational reliability of systems, components and assemblies of M1 cars was conducted in a dealership during 2022-2023. The study mainly involved cars with a sedan body and a McPherson front suspension. At the same time, the reason for contacting the service, the mileage of the car, as well as the types of work performed were recorded in each work order. The experimental data were processed using MSExcel and MatLab software from MathWorks.Resultsand conclusions. The conducted research allowed us to conclude that the appeals on the suspension of the car are almost twice as high as other appeals. The most expensive elements – the front shock struts, account for up to a third of all suspension failures. To assess the reliability indicators of alternative racks, the failure distribution law (normal), the probability of failure and uptime are determined, and the parameters of the distribution law are determined: mathematical expectation, standard deviation and coefficient of variation. It was found that the resource of the rear shock absorbers is at least 30% more, and there are significantly fewer calls at the service station. Thus, the operation of a car with racks from alternative manufacturers is quite reasonable, despite the fact that the resource of racks from alternative manufacturers is usually lower than that of the original brands.
- 12 March 2024
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 21 (1) , 98-107
Open AccessEvaluation of reliability indicators of shock absorbers struts of M1 category cars in conditions of violation of established market relations between end users of spare parts and suppliers
Introduction. Over the past two years, there has been a violation of established market relations between end users of spare parts and suppliers. This led, on the one hand, to a significant increase in the cost of automotive components, and, on the other, to a reorientation of the market to new alternative manufacturers and suppliers. The main purpose of the work was a statistical assessment of the reliability indicators of the most expensive suspension element – the McPherson suspension strut, in the conditions of replacing the original struts with analogues available on the market.Methods. The study of the operational reliability of systems, components and assemblies of M1 cars was conducted in a dealership during 2022-2023. The study mainly involved cars with a sedan body and a McPherson front suspension. At the same time, the reason for contacting the service, the mileage of the car, as well as the types of work performed were recorded in each work order. The experimental data were processed using MSExcel and MatLab software from MathWorks.Resultsand conclusions. The conducted research allowed us to conclude that the appeals on the suspension of the car are almost twice as high as other appeals. The most expensive elements – the front shock struts, account for up to a third of all suspension failures. To assess the reliability indicators of alternative racks, the failure distribution law (normal), the probability of failure and uptime are determined, and the parameters of the distribution law are determined: mathematical expectation, standard deviation and coefficient of variation. It was found that the resource of the rear shock absorbers is at least 30% more, and there are significantly fewer calls at the service station. Thus, the operation of a car with racks from alternative manufacturers is quite reasonable, despite the fact that the resource of racks from alternative manufacturers is usually lower than that of the original brands.
- 1 January 2024
- Published by Innovative Mashinostroenie Publishing
Process of functioning of a vehicle with an automated system of four-wheel drive on a stand with running drums
The article presents the process of functioning of a stand with running drums, as well as a wheeled vehicle with a plug-in complete drive in the modeling environment "Universal Mechanism 9". The differential equations of the functioning of a wheeled vehicle with a plug-in field drive are given. Graphs of the acceleration process of a wheeled vehicle on a stand with running drums with simulated rear axle slipping are shown. The data of the search experiment were compared with the calculations obtained. Keywords technical condition monitoring, diagnostics, control systems for plug-in all-wheel drive, stand with running drums, mathematical model, universal mechanism, full-support stand
- 1 January 2024
- Published by Innovative Mashinostroenie Publishing
Process of functioning of a vehicle with an automated system of four-wheel drive on a stand with running drums
The article presents the process of functioning of a stand with running drums, as well as a wheeled vehicle with a plug-in complete drive in the modeling environment "Universal Mechanism 9". The differential equations of the functioning of a wheeled vehicle with a plug-in field drive are given. Graphs of the acceleration process of a wheeled vehicle on a stand with running drums with simulated rear axle slipping are shown. The data of the search experiment were compared with the calculations obtained. Keywords technical condition monitoring, diagnostics, control systems for plug-in all-wheel drive, stand with running drums, mathematical model, universal mechanism, full-support stand
- Open Access
- 27 July 2023
- Published by ECO-Vector LLC in Tractors and Agricultural Machinery
- Vol. 90 (2) , 91-98
Low-temperature properties of fuel blends based on biodiesel derived from frying oil wastes
BACKGROUND: Automotive engines are one of the environment pollutants with harmful substances and greenhouse gases. Recently, the field of carbon-free or carbon-neutral energy has become the most relevant. In this regard, the task of reducing the carbon footprint of automotive equipment equipped with internal combustion engines remains urgent. This can be done by complete or partial replacement of the fuel with the carbon-neutral one, such as plant-origin biofuels. AIMS: Study of low-temperature properties of fuel blends based on biodiesel derived from frying oil wastes. MATERIALS AND METHODS: The vegetable oil ether was derived from purified frying oil wastes by esterification. Then fuel blends were obtained by mixing the derived ether with diesel fuel of different brands and butanol. The study of viscosity-temperature properties and density of the obtained fuel blends was carried out in the temperature range from -20C to 40C. The methods and equipment for determining these parameters meet the requirements of GOST. RESULTS: The obtained study results helped to conclude that blended biodiesel in certain proportions can be used as fuel even at negative ambient temperatures, which is not uncommon for the start of a sowing campaign in spring and the end of field work in autumn in sharply continental climatic conditions. CONCLUSIONS: The practical value of the study lies in the possibility of using fuel blends based on biodiesel derived from frying oil wastes at low temperatures.
- 27 July 2023
- Published by ECO-Vector LLC in Tractors and Agricultural Machinery
- Vol. 90 (2) , 91-98
Open AccessLow-temperature properties of fuel blends based on biodiesel derived from frying oil wastes
BACKGROUND: Automotive engines are one of the environment pollutants with harmful substances and greenhouse gases. Recently, the field of carbon-free or carbon-neutral energy has become the most relevant. In this regard, the task of reducing the carbon footprint of automotive equipment equipped with internal combustion engines remains urgent. This can be done by complete or partial replacement of the fuel with the carbon-neutral one, such as plant-origin biofuels. AIMS: Study of low-temperature properties of fuel blends based on biodiesel derived from frying oil wastes. MATERIALS AND METHODS: The vegetable oil ether was derived from purified frying oil wastes by esterification. Then fuel blends were obtained by mixing the derived ether with diesel fuel of different brands and butanol. The study of viscosity-temperature properties and density of the obtained fuel blends was carried out in the temperature range from -20C to 40C. The methods and equipment for determining these parameters meet the requirements of GOST. RESULTS: The obtained study results helped to conclude that blended biodiesel in certain proportions can be used as fuel even at negative ambient temperatures, which is not uncommon for the start of a sowing campaign in spring and the end of field work in autumn in sharply continental climatic conditions. CONCLUSIONS: The practical value of the study lies in the possibility of using fuel blends based on biodiesel derived from frying oil wastes at low temperatures.
- Open Access
- 25 November 2021
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 18 (5) , 534-543
Сhanging the lubricity of diesel fuel with vegetable oil additive
Intriduction. The environmental safety of cars with a diesel engine does not lose its relevance. In the conditions of stricter requirements for diesel fuel, the content of many substances harmful to the environment, including sulfur, is not allowed. As is known, low-sulfur fuels require the presence of additives that improve the lubricating properties of diesel fuel. Non-compliance with the requirements for lubricity significantly affects the resource of the fuel supply system of a diesel engine, primarily the Common Rail system. In order with the circumstances listed above, we hypothesized that vegetable oil can serve in small concentrations to improve the lubricating properties of fuels.Materials and methods. In our research, we conducted experiments using the standard HFRR method (highfrequency translational motion of a ball rubbing against a plate in fuel). A microscope was used to visually assess the wear spots and measure their size. Diesel fuel was taken as samples for experiments and vegetable oil was added to it as an additive in certain proportions.Discussion and conclusions. The vegetable oil additive can improve the lubricity of diesel fuel, even if it does not comply with GOST for this parameter. The experiments conducted allow us to conclude that the vegetable oil additive as a percentage of diesel fuel almost linearly reduces the diameter of the wear spot
- 25 November 2021
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 18 (5) , 534-543
Open AccessСhanging the lubricity of diesel fuel with vegetable oil additive
Intriduction. The environmental safety of cars with a diesel engine does not lose its relevance. In the conditions of stricter requirements for diesel fuel, the content of many substances harmful to the environment, including sulfur, is not allowed. As is known, low-sulfur fuels require the presence of additives that improve the lubricating properties of diesel fuel. Non-compliance with the requirements for lubricity significantly affects the resource of the fuel supply system of a diesel engine, primarily the Common Rail system. In order with the circumstances listed above, we hypothesized that vegetable oil can serve in small concentrations to improve the lubricating properties of fuels.Materials and methods. In our research, we conducted experiments using the standard HFRR method (highfrequency translational motion of a ball rubbing against a plate in fuel). A microscope was used to visually assess the wear spots and measure their size. Diesel fuel was taken as samples for experiments and vegetable oil was added to it as an additive in certain proportions.Discussion and conclusions. The vegetable oil additive can improve the lubricity of diesel fuel, even if it does not comply with GOST for this parameter. The experiments conducted allow us to conclude that the vegetable oil additive as a percentage of diesel fuel almost linearly reduces the diameter of the wear spot
- Open Access
- 1 February 2021
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1061 (1) , 012022
Variations in health of piezoelectric elements of the Common Rail electric hydraulic nozzles in the operating conditions
The article discusses operational reliability of piezoelectric elements of the Common Rail electric hydraulic nozzles. Attention is paid to the piezoelectric element’s health and its influence on the output injector parameters. It was assumed that capacity of the piezoelectric packet can be used as a diagnostic parameter. The studies carried out in the operating conditions identified failures of some elements of the electro-hydraulic nozzles, patterns of variations in capacity of the piezoelectric packet exposed to short or long-lasting heat treatment. Based on the data obtained, conclusions about the frequency of monitoring of the piezoelectric element’s health were drawn.
- 1 February 2021
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1061 (1) , 012022
Open AccessVariations in health of piezoelectric elements of the Common Rail electric hydraulic nozzles in the operating conditions
The article discusses operational reliability of piezoelectric elements of the Common Rail electric hydraulic nozzles. Attention is paid to the piezoelectric element’s health and its influence on the output injector parameters. It was assumed that capacity of the piezoelectric packet can be used as a diagnostic parameter. The studies carried out in the operating conditions identified failures of some elements of the electro-hydraulic nozzles, patterns of variations in capacity of the piezoelectric packet exposed to short or long-lasting heat treatment. Based on the data obtained, conclusions about the frequency of monitoring of the piezoelectric element’s health were drawn.
- Open Access
- 1 October 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 632 (1) , 012040
Rotational dynamics of piston diesel engine crankshaft with deactivated cylinders at idle
Diesel engines have been diagnosed on the basis of a dynamic method. To improve the informativity of the determination of general technical condition of each of the cylinders, it is proposed to apply a well-known test action i.e. termination of operation. In this case, analysis should be given to both the contribution of the cylinder in the operation and the acceleration imparted to the crankshaft by the cylinder in the absence of fuel supply. The paper presents a mathematical model that takes into account the relationship of the dynamics of rotation of the crankshaft with the pressure of gases in the cylinder, including when it is deactivated. The analysis of functional dependences has allowed to receive coupling equations between parameters of tightness of the cylinder and angular crankshaft acceleration. Analytical and experimental study of the crankshaft rotation dynamics with deactivated cylinders at idle speed allowed to conclude that parameters of the crankshaft rotation irregularity allow assessing the engine cylinders’ technical state both in the run mode and in the idle mode. The diagnostic parameter allows determining the leak tightness of the over-piston space at idle speed is suggested. It equals air pressure differential in the cylinder at 50 degrees before TDC and at 50 degrees after TDC over the pressure at 50 degrees before TDC. It was installed, that both extrema of angular accelerations and their average values during compression and expansion can be used to diagnose the technical condition of cylinders.
- 1 October 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 632 (1) , 012040
Open AccessRotational dynamics of piston diesel engine crankshaft with deactivated cylinders at idle
Diesel engines have been diagnosed on the basis of a dynamic method. To improve the informativity of the determination of general technical condition of each of the cylinders, it is proposed to apply a well-known test action i.e. termination of operation. In this case, analysis should be given to both the contribution of the cylinder in the operation and the acceleration imparted to the crankshaft by the cylinder in the absence of fuel supply. The paper presents a mathematical model that takes into account the relationship of the dynamics of rotation of the crankshaft with the pressure of gases in the cylinder, including when it is deactivated. The analysis of functional dependences has allowed to receive coupling equations between parameters of tightness of the cylinder and angular crankshaft acceleration. Analytical and experimental study of the crankshaft rotation dynamics with deactivated cylinders at idle speed allowed to conclude that parameters of the crankshaft rotation irregularity allow assessing the engine cylinders’ technical state both in the run mode and in the idle mode. The diagnostic parameter allows determining the leak tightness of the over-piston space at idle speed is suggested. It equals air pressure differential in the cylinder at 50 degrees before TDC and at 50 degrees after TDC over the pressure at 50 degrees before TDC. It was installed, that both extrema of angular accelerations and their average values during compression and expansion can be used to diagnose the technical condition of cylinders.