Cunchuan Zheng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Cunchuan Zheng has a total of 87 co-authors. Here are the top co-authors by number of shared publications:
Jie Deng
College of Chemistry and Chemical Engineering, Southwest Petroleum University
4 shared publicationsZhiyu Huang
Oil and Gas Field Applied Chemistry Key Laboratory of Sichuan Province, Southwest Petroleum University, Chengdu, People’s Republic of China
4 shared publications- Zhiyu Huang
College of Chemistry and Chemical Engineering, Southwest Petroleum University, Chengdu, Sichuan 610500, P. R. China
4 shared publications Chaozong Yan
School of Chemistry and Chemical Engineering, Southwest Petroleum University, Chengdu 610500, People’s Republic of China
3 shared publicationsKe Xu
PetroChina Research Institute of Petroleum Exploration & Development, Beijing 100083, People’s Republic of China
3 shared publicationsTailiang Zhang
3 shared publications
Latest Publications
- 26 August 2026
- Published by Taylor & Francis in Journal of Dispersion Science and Technology
- p. 1-11
Acid-driven self-thickening VES foamed acid: Tailoring foam stability and acid retardation via micellar evolution
1. With the rapid advancement of industrialization and urbanization, global energy demand has surged significantly.[1–3] Carbonate reservoirs are mainly composed of limestone and dolomite, with a h...
- 26 August 2026
- Published by Taylor & Francis in Journal of Dispersion Science and Technology
- p. 1-11
Acid-driven self-thickening VES foamed acid: Tailoring foam stability and acid retardation via micellar evolution
1. With the rapid advancement of industrialization and urbanization, global energy demand has surged significantly.[1–3] Carbonate reservoirs are mainly composed of limestone and dolomite, with a h...
- 30 July 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (31) , 22699-22712
Application of a Natural Deep Eutectic Solvent Prepared from Choline Chloride and Tannic Acid as a Shale Inhibitor for Wellbore Stabilization
To address wellbore instability issues associated with water-based drilling fluids during drilling operations and ensure the sustainable development of oil and gas resources, a deep eutectic solvent (DES–TA) is prepared by stirring and heating choline chloride with tannic acid, and its potential as a shale inhibitor is investigated. The inhibition performance of DES–TA was evaluated through hot-rolled recovery, clay linear swelling, and bentonite inhibition tests. The results revealed that DES–TA increased shale cutting recovery from 8.9 to 84.2% (a 75.3% increase) at 180 °C, inhibited the hydration swelling of 35 wt % bentonite at 90 °C, and reduced the swelling height of bentonite by 50.4% at 25 °C. In addition, the mechanism of action of DES–TA was analyzed through a series of analytical studies. DES–TA adsorbed onto the surface and interlayers of bentonite via electrostatic neutralization and hydrogen bonding, reduced the electrostatic repulsion between bentonite particles, and altered the hydrophilicity of the bentonite surface, thereby inhibiting the hydration and swelling of bentonite. DES–TA has excellent inhibition performance, but it has a serious adverse effect on the rheological properties and fluid loss of WBDF. When DES–TA is used, its compatibility with WBDF must be considered.
- 30 July 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (31) , 22699-22712
Application of a Natural Deep Eutectic Solvent Prepared from Choline Chloride and Tannic Acid as a Shale Inhibitor for Wellbore Stabilization
To address wellbore instability issues associated with water-based drilling fluids during drilling operations and ensure the sustainable development of oil and gas resources, a deep eutectic solvent (DES–TA) is prepared by stirring and heating choline chloride with tannic acid, and its potential as a shale inhibitor is investigated. The inhibition performance of DES–TA was evaluated through hot-rolled recovery, clay linear swelling, and bentonite inhibition tests. The results revealed that DES–TA increased shale cutting recovery from 8.9 to 84.2% (a 75.3% increase) at 180 °C, inhibited the hydration swelling of 35 wt % bentonite at 90 °C, and reduced the swelling height of bentonite by 50.4% at 25 °C. In addition, the mechanism of action of DES–TA was analyzed through a series of analytical studies. DES–TA adsorbed onto the surface and interlayers of bentonite via electrostatic neutralization and hydrogen bonding, reduced the electrostatic repulsion between bentonite particles, and altered the hydrophilicity of the bentonite surface, thereby inhibiting the hydration and swelling of bentonite. DES–TA has excellent inhibition performance, but it has a serious adverse effect on the rheological properties and fluid loss of WBDF. When DES–TA is used, its compatibility with WBDF must be considered.
- Open Access
Molecular Structure Regulation of Polyacrylamide-Based Drag Reducers on Solubility and Transient Gel-Layer Behavior: Molecular Dynamics and Experimental Study
This study aimed to clarify how molecular structure regulates the dissolution and transient gel-layer behavior of polyacrylamide-based dry-powder drag reducers for slickwater fracturing. In the Materials Studio 2020 software, molecular dynamics simulations were performed on five representative homopolymers, including: polyacrylamide (PAM), polyacrylic acid (PAA), poly(2-acrylamido-2-methylpropane sulfonic acid) (PAMPS), poly(N-vinylpyrrolidone) (PNVP), and poly [2-(acryloyloxy)ethyl]trimethylammonium chloride (PDAC). The results show that in pure water, PAA exhibits the strongest thermodynamic driving force with an interaction energy of −1005.5 kcal/mol and the lowest solvation free energy of −373.289 kcal/mol. Quantitative correlation analysis established that solvation energy and hydrogen bond density are primary predictors of macroscopic performance, yielding a correlation coefficient of R2 > 0.94. Experiments confirm that optimized AM/AA (7:3) and AM/AMPS (5:5) anionic copolymers achieve stable viscosity within 120 ± 5 s and 160 ± 8 s, respectively, representing a 60% reduction in dissolution time compared to conventional industrial PAM homopolymers. The polarity, charge density, and chain flexibility of functional groups jointly regulate polymer dissolution behavior. Anionic groups significantly improve dissolution performance by enhancing intramolecular electrostatic repulsion and hydration.
Open AccessMolecular Structure Regulation of Polyacrylamide-Based Drag Reducers on Solubility and Transient Gel-Layer Behavior: Molecular Dynamics and Experimental Study
This study aimed to clarify how molecular structure regulates the dissolution and transient gel-layer behavior of polyacrylamide-based dry-powder drag reducers for slickwater fracturing. In the Materials Studio 2020 software, molecular dynamics simulations were performed on five representative homopolymers, including: polyacrylamide (PAM), polyacrylic acid (PAA), poly(2-acrylamido-2-methylpropane sulfonic acid) (PAMPS), poly(N-vinylpyrrolidone) (PNVP), and poly [2-(acryloyloxy)ethyl]trimethylammonium chloride (PDAC). The results show that in pure water, PAA exhibits the strongest thermodynamic driving force with an interaction energy of −1005.5 kcal/mol and the lowest solvation free energy of −373.289 kcal/mol. Quantitative correlation analysis established that solvation energy and hydrogen bond density are primary predictors of macroscopic performance, yielding a correlation coefficient of R2 > 0.94. Experiments confirm that optimized AM/AA (7:3) and AM/AMPS (5:5) anionic copolymers achieve stable viscosity within 120 ± 5 s and 160 ± 8 s, respectively, representing a 60% reduction in dissolution time compared to conventional industrial PAM homopolymers. The polarity, charge density, and chain flexibility of functional groups jointly regulate polymer dissolution behavior. Anionic groups significantly improve dissolution performance by enhancing intramolecular electrostatic repulsion and hydration.
- Open Access
Rheology and Molecular Mechanisms of Fracturing Fluids: A Comparison of Three Thickener Types—A Case Study
To address the lack of systematic comparison regarding rheological properties and the unclear structure–property relationships among three core fracturing fluid materials including synthetic polymers, vegetable gums, and microbial polysaccharides, this study selected acrylamide-based polymers, hydroxypropyl guar gum and xanthan gum as the representative systems. The steady-state viscosity, rheological curves, thixotropy, viscoelasticity, and temperature-shear resistance of the three samples were systematically characterized at concentrations ranging from 0.1 to 0.7 wt% using an MCR301 rotational rheometer. The outcomes indicate that the structural strength values of all three materials increase with rising concentration, but their rheological behaviors and stability differ significantly due to distinct molecular structures. The acrylamide-based copolymer forms a temporary network via weak hydrogen bonds (amide-carboxyl or amide-amide) and physical entanglements, exhibiting thixotropy and a stress pre-elastic response. The most significant effects occur at 0.7 wt%, with a thixotropic loop area of 2.874 Pa·s−1 and a stress overshoot of 4.97 Pa.; hydroxypropyl guar gum has insufficient thermal stability and poor heat resistance. Its viscosity retention rate is as low as 31%, and it always exhibits a solution-type rheological property of G′ < G″; the xanthan gum exhibits elastic gel properties with tanδ < 1 due to its double-helix molecular structure. It has excellent temperature shear tolerance and the viscosity retention value can reach up to 98.6 mPa·s. Two mathematical models were established and demonstrated strong applicability: a modified Carreau model for flow curve fitting yielded a coefficient of determination (R2) greater than 0.95, enabling accurate description of fluid-type transitions; a four-parameter equation for temperature–shear resistance curves also achieved an R2 above 0.95, effectively characterizing viscosity evolution with temperature.
Open AccessRheology and Molecular Mechanisms of Fracturing Fluids: A Comparison of Three Thickener Types—A Case Study
To address the lack of systematic comparison regarding rheological properties and the unclear structure–property relationships among three core fracturing fluid materials including synthetic polymers, vegetable gums, and microbial polysaccharides, this study selected acrylamide-based polymers, hydroxypropyl guar gum and xanthan gum as the representative systems. The steady-state viscosity, rheological curves, thixotropy, viscoelasticity, and temperature-shear resistance of the three samples were systematically characterized at concentrations ranging from 0.1 to 0.7 wt% using an MCR301 rotational rheometer. The outcomes indicate that the structural strength values of all three materials increase with rising concentration, but their rheological behaviors and stability differ significantly due to distinct molecular structures. The acrylamide-based copolymer forms a temporary network via weak hydrogen bonds (amide-carboxyl or amide-amide) and physical entanglements, exhibiting thixotropy and a stress pre-elastic response. The most significant effects occur at 0.7 wt%, with a thixotropic loop area of 2.874 Pa·s−1 and a stress overshoot of 4.97 Pa.; hydroxypropyl guar gum has insufficient thermal stability and poor heat resistance. Its viscosity retention rate is as low as 31%, and it always exhibits a solution-type rheological property of G′ < G″; the xanthan gum exhibits elastic gel properties with tanδ < 1 due to its double-helix molecular structure. It has excellent temperature shear tolerance and the viscosity retention value can reach up to 98.6 mPa·s. Two mathematical models were established and demonstrated strong applicability: a modified Carreau model for flow curve fitting yielded a coefficient of determination (R2) greater than 0.95, enabling accurate description of fluid-type transitions; a four-parameter equation for temperature–shear resistance curves also achieved an R2 above 0.95, effectively characterizing viscosity evolution with temperature.
- Open Access
- 15 January 2026
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 11 (4) , 6464-6476
A CO 2 -Responsive Gel System (AM/NVP/DMAEMA) for Plugging High-Permeability Gas Channeling Zones in a CO 2 Flooding Process
To address the issue of CO2 channeling along high-permeability zones during the development of CO2 flooding in low-permeability reservoirs, this study developed a CO2-responsive gel system for gas channeling plugging. Through molecular design, a CO2-responsive polymer (AM/NVP/DMAEMA) was synthesized, and its structure was characterized. The results indicated that the successful synthesis of the polymer was confirmed. Constructed based on this CO2-responsive polymer (AM/NVP/DMAEMA), the CO2-responsive polymer gel system (designated as DKS) has the following formulation: the CO2-responsive polymer with a mass fraction of 0.5%, WD-1 with 0.8%, and WD-2 with 0.8%. Performance tests of DKS were conducted under relevant environmental conditions (e.g., different temperatures, salinities, and pressures). The results showed that the gelation strength of the system is above grade H with an elastic modulus (G′) > 2 Pa; after 30 days of aging, the gel strength remains above grade H, and the water loss rate after 30 days of aging is 2 flooding simulation experiment on artificial cores, DKS exhibited excellent injectability and plugging performance: the injection pressure is below 0.80 MPa, the plugging rate can reach over 95%, and the reduction rate of the CO2 outlet flow can reach over 95%. In a CO2 atmosphere, compared with conventional gels, DKS demonstrates outstanding gel strength and stability in CO2 environments, which holds a significant reference value for the efficient development of CO2 flooding in low-permeability reservoirs.
- 15 January 2026
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 11 (4) , 6464-6476
Open AccessA CO 2 -Responsive Gel System (AM/NVP/DMAEMA) for Plugging High-Permeability Gas Channeling Zones in a CO 2 Flooding Process
To address the issue of CO2 channeling along high-permeability zones during the development of CO2 flooding in low-permeability reservoirs, this study developed a CO2-responsive gel system for gas channeling plugging. Through molecular design, a CO2-responsive polymer (AM/NVP/DMAEMA) was synthesized, and its structure was characterized. The results indicated that the successful synthesis of the polymer was confirmed. Constructed based on this CO2-responsive polymer (AM/NVP/DMAEMA), the CO2-responsive polymer gel system (designated as DKS) has the following formulation: the CO2-responsive polymer with a mass fraction of 0.5%, WD-1 with 0.8%, and WD-2 with 0.8%. Performance tests of DKS were conducted under relevant environmental conditions (e.g., different temperatures, salinities, and pressures). The results showed that the gelation strength of the system is above grade H with an elastic modulus (G′) > 2 Pa; after 30 days of aging, the gel strength remains above grade H, and the water loss rate after 30 days of aging is 2 flooding simulation experiment on artificial cores, DKS exhibited excellent injectability and plugging performance: the injection pressure is below 0.80 MPa, the plugging rate can reach over 95%, and the reduction rate of the CO2 outlet flow can reach over 95%. In a CO2 atmosphere, compared with conventional gels, DKS demonstrates outstanding gel strength and stability in CO2 environments, which holds a significant reference value for the efficient development of CO2 flooding in low-permeability reservoirs.
- 17 May 2025
- Published by Elsevier in Surfaces and Interfaces
- Vol. 68
Probing synergistic effect of doped transition metals for enhanced ORR/OER performance: Two-factor modified NiOOH
- 17 May 2025
- Published by Elsevier in Surfaces and Interfaces
- Vol. 68
Probing synergistic effect of doped transition metals for enhanced ORR/OER performance: Two-factor modified NiOOH
- 3 April 2025
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 47 (1) , 8744-8757
Preparation of water-based drilling cuttings derived non-fired bricks and insights into heavy metal fixation mechanisms
- 3 April 2025
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 47 (1) , 8744-8757
Preparation of water-based drilling cuttings derived non-fired bricks and insights into heavy metal fixation mechanisms
- 19 February 2025
- Published by Taylor & Francis in Petroleum Science and Technology
- Vol. 44 (2) , 205-232
Reusable light hydrocarbon-stabilizer system applied to heavy oil viscosity reduction
- 19 February 2025
- Published by Taylor & Francis in Petroleum Science and Technology
- Vol. 44 (2) , 205-232
Reusable light hydrocarbon-stabilizer system applied to heavy oil viscosity reduction
- 11 November 2024
- Published by Taylor & Francis in Petroleum Science and Technology
- p. 1-19
Study on the preparation and mechanism of oil-soluble amphiphilic polymer asphaltene inhibitor
- 11 November 2024
- Published by Taylor & Francis in Petroleum Science and Technology
- p. 1-19
Study on the preparation and mechanism of oil-soluble amphiphilic polymer asphaltene inhibitor