Duan Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Duan Chen has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Changcai Zhao
Key Laboratory of Advanced Forging & Stamping Technology and Science, Ministry of Education of China, Yanshan University, Qinhuangdao, China
2 shared publications - Bing Du
National-Local Joint Engineering Research Center for Advanced Manufacturing, Forming Technology and Equipment, Yanshan University, Qinhuangdao City, China
1 shared publication - Guang Chen
Key Laboratory of Advanced Forging & Stamping Technology and Science (Yanshan University), Ministry of Education of China, Qinhuangdao 066004, China
1 shared publication - Xiaoyi Chen
Key Laboratory of Advanced Forging & Stamping Technology and Science (Yanshan University), Ministry of Education of China, Qinhuangdao 066004, China
1 shared publication - Xin Zhang
Key Laboratory of Advanced Forging and Stamping Technology and Science of Ministry of Education, Yanshan University, Qinhuangdao 066004, China
1 shared publication - Yang Li
Key Laboratory of Advanced Forging and Stamping Technology and Science of Ministry of Education, Yanshan University, Qinhuangdao 066004, China
1 shared publication
Latest Publications
- Open Access
Mechanical Analysis of Deformation Law in the Flange Area of Box-Shaped Parts during Deep Drawing
The investigation of deformation law is the theoretical basis for analyzing instability wrinkling and forming performance during the sheet-metal-forming process. In order to explore the deformation law in the flange area of box-shaped parts and conduct qualitative and quantitative analysis on stress and strain, it is assumed that the deformation law of the mass point on the zero line of shear stress in the corner area is equal to that of the axisymmetric parts. Based on the basic assumptions that the equivalent strain in the flange area is linear with the radius along the radial direction, the simple linear relationship between in-plane shear stress and geometric parameters and the expressions of stress and strain in each region of the flange area are derived. The theoretical derivation is compared and analyzed through finite element (FE) simulation and process tests. The results demonstrate that the theoretical calculation results are consistent with the trends of experimental and simulation results. The calculation accuracy of equivalent strain is higher than that of stress calculation, which reveals that calculation accuracy is sensitive to the parameters in the material constitutive model. The theoretical analysis has reference significance for exploring the law of deep drawing deformation, optimizing the forming process and guiding the actual production.
Open AccessMechanical Analysis of Deformation Law in the Flange Area of Box-Shaped Parts during Deep Drawing
The investigation of deformation law is the theoretical basis for analyzing instability wrinkling and forming performance during the sheet-metal-forming process. In order to explore the deformation law in the flange area of box-shaped parts and conduct qualitative and quantitative analysis on stress and strain, it is assumed that the deformation law of the mass point on the zero line of shear stress in the corner area is equal to that of the axisymmetric parts. Based on the basic assumptions that the equivalent strain in the flange area is linear with the radius along the radial direction, the simple linear relationship between in-plane shear stress and geometric parameters and the expressions of stress and strain in each region of the flange area are derived. The theoretical derivation is compared and analyzed through finite element (FE) simulation and process tests. The results demonstrate that the theoretical calculation results are consistent with the trends of experimental and simulation results. The calculation accuracy of equivalent strain is higher than that of stress calculation, which reveals that calculation accuracy is sensitive to the parameters in the material constitutive model. The theoretical analysis has reference significance for exploring the law of deep drawing deformation, optimizing the forming process and guiding the actual production.
- Open Access
Research on Hydraulic Push-Pull Bending Process of Ultra-Thin-Walled Tubes
Due to their high strength, high performance, and lightweight characteristics, bent tubes are widely used in many high-end industries, such as aviation, aerospace, shipbuilding, automobile, and petrochemical industries. Ultra-thin-walled (thickness-to-diameter ratio t/D < 0.01) bent tubes are more prone to wrinkling, fracture, and cross-section distortion than ordinary bent tubes, which are difficult to form integrally by traditional bending processes. In this paper, a new bending process with combined loading of hydraulic pressure, push, and pull was proposed to provide a new method for the bending of ultra-thin-walled tube. This process is characterized by the ability to optimize the combination of push, pull, and internal pressure according to the actual bending process in order to minimize the wrinkling of ultra-thin-walled tube during bending. Based on ABAQUS finite element (FE) software, the FE model of the hydraulic push-pull bending process for ultra-thin-walled tube was established. The influence of internal pressure, die clearance, and friction coefficient on the forming quality of bent tubes was discussed, and the optimum process parameters were obtained. Bent tubes with an initial thickness of 0.3 mm, diameter of 60 mm, and bending radius of 165 mm were manufactured in experiments. Through the comparative analysis of experiment and simulation, the accuracy of the FE simulation was verified.
Open AccessResearch on Hydraulic Push-Pull Bending Process of Ultra-Thin-Walled Tubes
Due to their high strength, high performance, and lightweight characteristics, bent tubes are widely used in many high-end industries, such as aviation, aerospace, shipbuilding, automobile, and petrochemical industries. Ultra-thin-walled (thickness-to-diameter ratio t/D < 0.01) bent tubes are more prone to wrinkling, fracture, and cross-section distortion than ordinary bent tubes, which are difficult to form integrally by traditional bending processes. In this paper, a new bending process with combined loading of hydraulic pressure, push, and pull was proposed to provide a new method for the bending of ultra-thin-walled tube. This process is characterized by the ability to optimize the combination of push, pull, and internal pressure according to the actual bending process in order to minimize the wrinkling of ultra-thin-walled tube during bending. Based on ABAQUS finite element (FE) software, the FE model of the hydraulic push-pull bending process for ultra-thin-walled tube was established. The influence of internal pressure, die clearance, and friction coefficient on the forming quality of bent tubes was discussed, and the optimum process parameters were obtained. Bent tubes with an initial thickness of 0.3 mm, diameter of 60 mm, and bending radius of 165 mm were manufactured in experiments. Through the comparative analysis of experiment and simulation, the accuracy of the FE simulation was verified.