Hao Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hao Li has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
Ganesh Balamurugan
Intel Corporation, Hillsboro, OR, USA
6 shared publicationsJames Jaussi
Intel Corporation, USA
6 shared publicationsBryan Casper
Intel Labs, Intel, Hillsboro, OR 97124 USA
3 shared publicationsChun-Ming Hsu
Intel Corporation, Hillsboro, OR, USA
3 shared publicationsHaisheng Rong
Intel Corporation, USA
3 shared publications- Ranjeet Kumar
Intel Corporation
3 shared publications
Latest Publications
- 23 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (5) , 1397-1408
A 128 Gb/s, 11.2 mW Single-Ended PAM4 Linear TIA With 2.7 μArms Input Noise in 22 nm FinFET CMOS
We review the design trade-offs that exist in CMOS inverter-based shunt-feedback transimpedance amplifier (SF-TIA) when optimizing for energy efficiency. We analyze the performance of series and shunt inductive peaking techniques for bandwidth enhancement and identify the most effective one for low-power CMOS TIAs. As a design example, we present a 128-Gb/s single-ended linear transimpedance amplifier (TIA) intended for use in receivers for 400-G Ethernet optical modules and co-packaged optics. The inverter-based SF-TIA is implemented in a 22-nm fin field-effect transistor (FinFET) CMOS technology, supporting a data rate of 128-Gb/s PAM4 with a dc transimpedance gain of$59.3~{\mathrm{ dB}}{\cdot }\Omega $ while dissipating only 11.2 mW of power from a 0.8-V supply. It achieves a 3-dB transimpedance bandwidth of 45.5 GHz with a total integrated input referred noise current of$2.7~\mu \text{A}_{\text{rms}}$ . These results improve upon the state-of-the-art BiCMOS/CMOS linear TIAs, demonstrating the potential for building highly integrated, low-cost, high-sensitivity 100+G CMOS optical receivers using FinFET CMOS process technology.- 23 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (5) , 1397-1408
A 128 Gb/s, 11.2 mW Single-Ended PAM4 Linear TIA With 2.7 μArms Input Noise in 22 nm FinFET CMOS
We review the design trade-offs that exist in CMOS inverter-based shunt-feedback transimpedance amplifier (SF-TIA) when optimizing for energy efficiency. We analyze the performance of series and shunt inductive peaking techniques for bandwidth enhancement and identify the most effective one for low-power CMOS TIAs. As a design example, we present a 128-Gb/s single-ended linear transimpedance amplifier (TIA) intended for use in receivers for 400-G Ethernet optical modules and co-packaged optics. The inverter-based SF-TIA is implemented in a 22-nm fin field-effect transistor (FinFET) CMOS technology, supporting a data rate of 128-Gb/s PAM4 with a dc transimpedance gain of$59.3~{\mathrm{ dB}}{\cdot }\Omega $ while dissipating only 11.2 mW of power from a 0.8-V supply. It achieves a 3-dB transimpedance bandwidth of 45.5 GHz with a total integrated input referred noise current of$2.7~\mu \text{A}_{\text{rms}}$ . These results improve upon the state-of-the-art BiCMOS/CMOS linear TIAs, demonstrating the potential for building highly integrated, low-cost, high-sensitivity 100+G CMOS optical receivers using FinFET CMOS process technology.- 1 January 2022
- Published by Optica Publishing Group
- p. M2D.1
A 106 Gb/s 2.5 Vppd Linear Microring Modulator Driver with Integrated Photocurrent Sensor in 28nm CMOS
A low-power CMOS linear driver IC, optimized for microring modulator-based co-packaged optics, is presented. This 2.5 Vppd driver, assembled with a photonic IC, achieves 2 dB TDECQ at 106 Gb/s PAM4 with 1.33 pJ/bit efficiency.
- 1 January 2022
- Published by Optica Publishing Group
- p. M2D.1
A 106 Gb/s 2.5 Vppd Linear Microring Modulator Driver with Integrated Photocurrent Sensor in 28nm CMOS
A low-power CMOS linear driver IC, optimized for microring modulator-based co-packaged optics, is presented. This 2.5 Vppd driver, assembled with a photonic IC, achieves 2 dB TDECQ at 106 Gb/s PAM4 with 1.33 pJ/bit efficiency.
- 23 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (4) , 1187-1198
Silicon Photonic Microring-Based 4 × 112 Gb/s WDM Transmitter With Photocurrent-Based Thermal Control in 28-nm CMOS
This work presents a hybrid-integrated 4-λ micro-ring modulator-based wavelength-division multiplexed (WDM) optical transmitter (OTX) in the O-band, suitable for co-packaged optics. It supports up to 112 Gb/s per wavelength using high-bandwidth micro-ring modulators (MRMs) together with nonlinear equalization in the driver electronics. A thermal control scheme using MRM photocurrent to sense process and temperature variations is implemented, enabling <0.05 dB TDECQ penalty over 10 °C. This compact photocurrent-based control method significantly reduces the hardware and packaging overhead required for ring-based WDM transceivers. Measurements from a 4-λ OTX with 28-nm CMOS electronic IC (EIC) and custom silicon photonic IC (PIC) show the OTX supports 112 Gb/s with <0.7 dB TDECQ across all four channels while dissipating 5.8 pJ/bit in the electronics.
- 23 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (4) , 1187-1198
Silicon Photonic Microring-Based 4 × 112 Gb/s WDM Transmitter With Photocurrent-Based Thermal Control in 28-nm CMOS
This work presents a hybrid-integrated 4-λ micro-ring modulator-based wavelength-division multiplexed (WDM) optical transmitter (OTX) in the O-band, suitable for co-packaged optics. It supports up to 112 Gb/s per wavelength using high-bandwidth micro-ring modulators (MRMs) together with nonlinear equalization in the driver electronics. A thermal control scheme using MRM photocurrent to sense process and temperature variations is implemented, enabling <0.05 dB TDECQ penalty over 10 °C. This compact photocurrent-based control method significantly reduces the hardware and packaging overhead required for ring-based WDM transceivers. Measurements from a 4-λ OTX with 28-nm CMOS electronic IC (EIC) and custom silicon photonic IC (PIC) show the OTX supports 112 Gb/s with <0.7 dB TDECQ across all four channels while dissipating 5.8 pJ/bit in the electronics.
- 18 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (3) , 757-766
A Scalable 32–56 Gb/s 0.56–1.28 pJ/b Voltage-Mode VCSEL-Based Optical Transmitter in 28-nm CMOS
An optical transmitter (TX) data path is demonstrated in 28-nm CMOS which drives an 850-nm vertical-cavity surface-emitting laser (VCSEL) up to 56 Gb/s non-return-to-zero (NRZ). A dc-coupled single-ended voltage-mode driver employs area- and energy-efficient equalization techniques including slew-rate-based pulse-shaping at 2x more energy- and area-efficient than optical TXs reported to date. The highly digital circuit architecture enables the supply scalability to 0.7 and 0.85 V to operate the TX at 32 and 40 Gb/s at 0.56 and 0.77 pJ/b, respectively, which is ≥ 4x more energy-efficient than the prior art.
- 18 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (3) , 757-766
A Scalable 32–56 Gb/s 0.56–1.28 pJ/b Voltage-Mode VCSEL-Based Optical Transmitter in 28-nm CMOS
An optical transmitter (TX) data path is demonstrated in 28-nm CMOS which drives an 850-nm vertical-cavity surface-emitting laser (VCSEL) up to 56 Gb/s non-return-to-zero (NRZ). A dc-coupled single-ended voltage-mode driver employs area- and energy-efficient equalization techniques including slew-rate-based pulse-shaping at 2x more energy- and area-efficient than optical TXs reported to date. The highly digital circuit architecture enables the supply scalability to 0.7 and 0.85 V to operate the TX at 32 and 40 Gb/s at 0.56 and 0.77 pJ/b, respectively, which is ≥ 4x more energy-efficient than the prior art.
- 14 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (1) , 44-53
A 100-Gb/s PAM-4 Optical Receiver With 2-Tap FFE and 2-Tap Direct-Feedback DFE in 28-nm CMOS
Optical receivers (ORXs) with integrated CMOS electronics enable compact, low-power solutions for 400-G Ethernet and co-packaged optics. In this article, we present a 100-Gb/s PAM-4 ORX with TIA and sampler integrated into a single 28-nm CMOS IC. ORX sensitivity is optimized using a low noise, sub-Nyquist bandwidth TIA followed by a mixed signal sampler that includes 2-tap FFE and 2-tap DFE. A distributed current-integrating summer helps meet feedback latency requirements of 50-Gbaud direct-feedback PAM-4 DFE. Measurements characterizing the CMOS linear TIA indicate ~23-GHz trans-impedance (ZT) bandwidth (BW) with-2.5 μA $_{{rms}}$ input-referred noise. Optical measurement results at 100 Gb/s show that -8.9-dBm sensitivity is achieved at 2.4e-4 BER with 3.9-pJ/bit energy efficiency.- 14 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (1) , 44-53
A 100-Gb/s PAM-4 Optical Receiver With 2-Tap FFE and 2-Tap Direct-Feedback DFE in 28-nm CMOS
Optical receivers (ORXs) with integrated CMOS electronics enable compact, low-power solutions for 400-G Ethernet and co-packaged optics. In this article, we present a 100-Gb/s PAM-4 ORX with TIA and sampler integrated into a single 28-nm CMOS IC. ORX sensitivity is optimized using a low noise, sub-Nyquist bandwidth TIA followed by a mixed signal sampler that includes 2-tap FFE and 2-tap DFE. A distributed current-integrating summer helps meet feedback latency requirements of 50-Gbaud direct-feedback PAM-4 DFE. Measurements characterizing the CMOS linear TIA indicate ~23-GHz trans-impedance (ZT) bandwidth (BW) with-2.5 μA $_{{rms}}$ input-referred noise. Optical measurement results at 100 Gb/s show that -8.9-dBm sensitivity is achieved at 2.4e-4 BER with 3.9-pJ/bit energy efficiency.- 22 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 56 (1) , 19-29
A 3-D-Integrated Silicon Photonic Microring-Based 112-Gb/s PAM-4 Transmitter With Nonlinear Equalization and Thermal Control
Microring modulators (MRMs) with CMOS electronics enable compact low power transmitter solutions for 400G Ethernet and co-packaged optical transceivers. In this article, we present a 3-D-integrated 112-Gb/s pulse amplitude modulation (PAM)-4 optical transmitter (OTX) using silicon photonic MRM, on-chip laser, and co-packaged 28-nm CMOS driver. The 3-Vpp driver includes a lookup table (LUT)-based PAM-4 nonlinear equalizer to address static and dynamic MRM nonlinearities. An integrated thermal control method that is insensitive to input power fluctuations is proposed to compensate for the temperature sensitivity of MRMs. PAM-4 measurement results of our OTX at 112 Gb/s show that transmitter dispersion eye closure quaternary (TDECQ) <1.5 dB is achieved from 28 °C to 55 °C with 7.4-pJ/bit energy efficiency including on-chip laser.
- 22 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 56 (1) , 19-29
A 3-D-Integrated Silicon Photonic Microring-Based 112-Gb/s PAM-4 Transmitter With Nonlinear Equalization and Thermal Control
Microring modulators (MRMs) with CMOS electronics enable compact low power transmitter solutions for 400G Ethernet and co-packaged optical transceivers. In this article, we present a 3-D-integrated 112-Gb/s pulse amplitude modulation (PAM)-4 optical transmitter (OTX) using silicon photonic MRM, on-chip laser, and co-packaged 28-nm CMOS driver. The 3-Vpp driver includes a lookup table (LUT)-based PAM-4 nonlinear equalizer to address static and dynamic MRM nonlinearities. An integrated thermal control method that is insensitive to input power fluctuations is proposed to compensate for the temperature sensitivity of MRMs. PAM-4 measurement results of our OTX at 112 Gb/s show that transmitter dispersion eye closure quaternary (TDECQ) <1.5 dB is achieved from 28 °C to 55 °C with 7.4-pJ/bit energy efficiency including on-chip laser.
- 30 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 38 (1) , 131-138
A 112 Gb/s PAM4 Silicon Photonics Transmitter With Microring Modulator and CMOS Driver
Microring modulators (MRMs) with CMOS electronics enable compact low power transmitter solutions for 400G Ethernet and future on-package optical transceivers. In this paper, we present a 112 Gb/s PAM4 transmitter using silicon photonic MRM, on-chip laser and co-packaged 28nm CMOS driver. We describe the impact of static and dynamic MRM nonlinearity on PAM4 signaling and present a dual path nonlinear pre-distortion technique to compensate both effects. PAM4 measurement results of our transmitter at 112 Gb/s show that TDECQ <0.7 dB is achieved from 30°C to 60°C while dissipating 6 pJ/bit. We also present link level measurements at 112 Gb/s PAM4 obtained by coupling this transmitter with our previously published CMOS TIA-based receiver, to demonstrate the feasibility of low cost optical transceivers through CMOS integration of optical interface circuits.
- 30 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 38 (1) , 131-138
A 112 Gb/s PAM4 Silicon Photonics Transmitter With Microring Modulator and CMOS Driver
Microring modulators (MRMs) with CMOS electronics enable compact low power transmitter solutions for 400G Ethernet and future on-package optical transceivers. In this paper, we present a 112 Gb/s PAM4 transmitter using silicon photonic MRM, on-chip laser and co-packaged 28nm CMOS driver. We describe the impact of static and dynamic MRM nonlinearity on PAM4 signaling and present a dual path nonlinear pre-distortion technique to compensate both effects. PAM4 measurement results of our transmitter at 112 Gb/s show that TDECQ <0.7 dB is achieved from 30°C to 60°C while dissipating 6 pJ/bit. We also present link level measurements at 112 Gb/s PAM4 obtained by coupling this transmitter with our previously published CMOS TIA-based receiver, to demonstrate the feasibility of low cost optical transceivers through CMOS integration of optical interface circuits.
- 1 January 2019
- Published by Optica Publishing Group
- p. Th4A.4
A 112 Gb/s PAM4 Transmitter with Silicon Photonics Microring Modulator and CMOS Driver
We demonstrate a 112 Gb/s PAM4 transmitter using silicon photonics microring modulator, on-chip laser and co-packaged CMOS driver. Measured TDECQ is <0.7 dB from 30°C to 60°C with on-chip nonlinear feed-forward equalization enabled.
- 1 January 2019
- Published by Optica Publishing Group
- p. Th4A.4
A 112 Gb/s PAM4 Transmitter with Silicon Photonics Microring Modulator and CMOS Driver
We demonstrate a 112 Gb/s PAM4 transmitter using silicon photonics microring modulator, on-chip laser and co-packaged CMOS driver. Measured TDECQ is <0.7 dB from 30°C to 60°C with on-chip nonlinear feed-forward equalization enabled.