Diogo Costa Gonçalves
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Diogo Costa Gonçalves has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Raul Duarte Salgueiral Gomes Campilho
CIDEM, ISEP, Polytechnic of Porto, R. Dr. António Bernardino de Almeida, 431, 4200-072 Porto, Portugal
13 shared publications - Luís Daniel Costa Ramalho
INEGI, Institute of Mechanical Engineering
11 shared publications - Jorge Belinha
School of Engineering, Polytechnic of Porto
10 shared publications - Isidro de Jesus Sanchez-Arce
INEGI – Pólo FEUP
5 shared publications - J. D. F. Lopes
School of Engineering, Polytechnic of Porto, ISEP-IPP, Porto, Portugal
4 shared publications J. Belinha
3 shared publications
Latest Publications
- 17 November 2026
- Published by Emerald Publishing in International Journal of Structural Integrity
- p. 1-20
Meshless radial point interpolation evaluation of pure tensile and shear crack growth in bonded joints
Purpose: The purpose of this work is to investigate the application of a meshless approach to simulate crack growth in adhesive joints under pure mode I and mode II fracture propagation. Design/methodology/approach: A meshless method, the Radial Point Interpolation Method, is incorporated in a fracture propagation algorithm. The pure mode critical energy release rate criterion, for mode I or mode II fracture propagation, is used. The fracture energy at the crack tip is obtained by distinct analytical data reduction schemes developed for mode I and mode II tests in adhesive joints, and compared against its critical value defined experimentally. Findings: In the present work, it was found that the meshless approach accurately predicts the experimental data in mode I and mode II fracture propagation. In addition, the stress analysis of Double Cantilever Beam and End-Notched Flexure tests demonstrates the suitability of the numerical approach to produce expected and smooth stress fields at the intricate adhesive layer. Originality/value: Adhesively bonded joints are commonly analysed using commercial Finite Element Method (FEM) software. In this work, an alternative approach is proposed, providing assets that often hinder complex numerical analyses using traditional FEMs.
- 17 November 2026
- Published by Emerald Publishing in International Journal of Structural Integrity
- p. 1-20
Meshless radial point interpolation evaluation of pure tensile and shear crack growth in bonded joints
Purpose: The purpose of this work is to investigate the application of a meshless approach to simulate crack growth in adhesive joints under pure mode I and mode II fracture propagation. Design/methodology/approach: A meshless method, the Radial Point Interpolation Method, is incorporated in a fracture propagation algorithm. The pure mode critical energy release rate criterion, for mode I or mode II fracture propagation, is used. The fracture energy at the crack tip is obtained by distinct analytical data reduction schemes developed for mode I and mode II tests in adhesive joints, and compared against its critical value defined experimentally. Findings: In the present work, it was found that the meshless approach accurately predicts the experimental data in mode I and mode II fracture propagation. In addition, the stress analysis of Double Cantilever Beam and End-Notched Flexure tests demonstrates the suitability of the numerical approach to produce expected and smooth stress fields at the intricate adhesive layer. Originality/value: Adhesively bonded joints are commonly analysed using commercial Finite Element Method (FEM) software. In this work, an alternative approach is proposed, providing assets that often hinder complex numerical analyses using traditional FEMs.
- Open Access
Impact Performance Enhancement of Dual-Adhesive Joints Through Adhesive and Geometric Parametric Investigation
Adhesively bonded joints are widely used in engineering structures due to their high strength-to-weight ratio and improved stress transfer. However, stress concentrations near the overlap edges limit their performance. Dual-adhesive joints (DAJs) combine adhesives with different mechanical properties to improve stress distribution and delay failure, but their behavior under impact loads is insufficiently understood. This work investigates the impact performance of steel single-lap DAJs using Cohesive Zone Modelling (CZM). Unlike previous studies that mainly focused on either adhesive selection or geometric parametric investigation separately under static loading conditions, this work provides a combined assessment of adhesive and mixed geometric modifications on the impact response of dual-adhesive joints. The numerical approach was first validated against experimental results, showing good strength predictions. Three adhesive combinations were studied, and the influence of outer chamfers, inner chamfers, and adhesive fillets was evaluated on stress distributions, maximum load (Pm), maximum load displacement (δm), and absorbed energy (E). Adhesive fillets were the most effective geometric modification, significantly reducing peel (σy) and shear stress (τxy) concentrations and improving performance. The DP8005+AV138 and DP8005+XNR6852E-2 adhesive combinations exhibited the best behavior, with the adhesive fillet configuration increasing Pm by up to 40.8% and E by up to 59.7% compared with the reference geometry. Outer chamfers provided moderate improvements, whereas inner chamfers had a limited or negative influence on joint performance. Combining geometric modifications improved stress distributions but did not outperform the best fillet-only configurations.
Open AccessImpact Performance Enhancement of Dual-Adhesive Joints Through Adhesive and Geometric Parametric Investigation
Adhesively bonded joints are widely used in engineering structures due to their high strength-to-weight ratio and improved stress transfer. However, stress concentrations near the overlap edges limit their performance. Dual-adhesive joints (DAJs) combine adhesives with different mechanical properties to improve stress distribution and delay failure, but their behavior under impact loads is insufficiently understood. This work investigates the impact performance of steel single-lap DAJs using Cohesive Zone Modelling (CZM). Unlike previous studies that mainly focused on either adhesive selection or geometric parametric investigation separately under static loading conditions, this work provides a combined assessment of adhesive and mixed geometric modifications on the impact response of dual-adhesive joints. The numerical approach was first validated against experimental results, showing good strength predictions. Three adhesive combinations were studied, and the influence of outer chamfers, inner chamfers, and adhesive fillets was evaluated on stress distributions, maximum load (Pm), maximum load displacement (δm), and absorbed energy (E). Adhesive fillets were the most effective geometric modification, significantly reducing peel (σy) and shear stress (τxy) concentrations and improving performance. The DP8005+AV138 and DP8005+XNR6852E-2 adhesive combinations exhibited the best behavior, with the adhesive fillet configuration increasing Pm by up to 40.8% and E by up to 59.7% compared with the reference geometry. Outer chamfers provided moderate improvements, whereas inner chamfers had a limited or negative influence on joint performance. Combining geometric modifications improved stress distributions but did not outperform the best fillet-only configurations.
- 20 April 2026
- Published by Taylor & Francis in Journal of Adhesion Science and Technology
- p. 1-18
Mixed-mode crack growth prediction in bonded joints using a meshless method
1. Numerical simulation of adhesively bonded joints is a demanding challenge in engineering, especially in mixed-mode fracture applications, due to the intricate stress fields and complex interface...
- 20 April 2026
- Published by Taylor & Francis in Journal of Adhesion Science and Technology
- p. 1-18
Mixed-mode crack growth prediction in bonded joints using a meshless method
1. Numerical simulation of adhesively bonded joints is a demanding challenge in engineering, especially in mixed-mode fracture applications, due to the intricate stress fields and complex interface...
- 29 March 2026
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 149
Meshless modeling of mixed-mode fracture propagation in double lap adhesive joints
- 29 March 2026
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 149
Meshless modeling of mixed-mode fracture propagation in double lap adhesive joints
- 2 December 2025
- Published by Taylor & Francis in Journal of Adhesion Science and Technology
- Vol. 40 (8) , 1438-1454
Strength prediction of an impacted composite adhesive single lap joint using the ISSF criterion
- 2 December 2025
- Published by Taylor & Francis in Journal of Adhesion Science and Technology
- Vol. 40 (8) , 1438-1454
Strength prediction of an impacted composite adhesive single lap joint using the ISSF criterion
- 26 October 2025
- Published by Springer Nature
- p. 68-79
Meshless Fracture Mechanics Approach to Mixed-Mode Crack Growth in Adhesively Bonded Lap Joints
- 26 October 2025
- Published by Springer Nature
- p. 68-79
Meshless Fracture Mechanics Approach to Mixed-Mode Crack Growth in Adhesively Bonded Lap Joints
- 23 September 2023
- Published by World Scientific Pub Co Pte Ltd in International Journal of Applied Mechanics
- Vol. 15 (10)
Free Vibration Parametric Study of a Double Lap Joint Using the Radial Point Interpolation Method
Adhesive joints are an increasingly important joining method, in part due to usually being lighter than the alternatives, which is very important in the search for more energy efficient transportation. However, the amount of studies focused on the free-vibration behavior of adhesive joints is currently very limited. Since this knowledge is important, to ensure that a joint is working outside its natural frequencies, this work sets out to perform a parametric study of a Double Lap Joint (DLJ) using the Radial Point Interpolation Method (RPIM), a meshless method. Using the RPIM in the free vibration of adhesive joints is the next step for this numerical method, after using it in the static analysis of adhesive joints. Considering that this is one of the first uses of this method in this type of problem it is also necessary to validate it. This task was performed in this work by comparing it with the Finite Element Method (FEM), which is the standard numerical method for this type of problem. The validation was successful, showing very small differences between the two numerical methods. The parametric study should aid future adhesive joint designers to develop safer joint. It showed that changes to the adhesive produce diminutive changes to the natural frequencies of the joints. On the other hand, changes to the adherents change the natural frequencies significantly. The overlap length had different effects on the different modes.
- 23 September 2023
- Published by World Scientific Pub Co Pte Ltd in International Journal of Applied Mechanics
- Vol. 15 (10)
Free Vibration Parametric Study of a Double Lap Joint Using the Radial Point Interpolation Method
Adhesive joints are an increasingly important joining method, in part due to usually being lighter than the alternatives, which is very important in the search for more energy efficient transportation. However, the amount of studies focused on the free-vibration behavior of adhesive joints is currently very limited. Since this knowledge is important, to ensure that a joint is working outside its natural frequencies, this work sets out to perform a parametric study of a Double Lap Joint (DLJ) using the Radial Point Interpolation Method (RPIM), a meshless method. Using the RPIM in the free vibration of adhesive joints is the next step for this numerical method, after using it in the static analysis of adhesive joints. Considering that this is one of the first uses of this method in this type of problem it is also necessary to validate it. This task was performed in this work by comparing it with the Finite Element Method (FEM), which is the standard numerical method for this type of problem. The validation was successful, showing very small differences between the two numerical methods. The parametric study should aid future adhesive joint designers to develop safer joint. It showed that changes to the adhesive produce diminutive changes to the natural frequencies of the joints. On the other hand, changes to the adherents change the natural frequencies significantly. The overlap length had different effects on the different modes.
- Open Access
- 2 August 2023
- Published by Elsevier in Composites Part C: Open Access
- Vol. 12
Simulation of mode II fracture propagation in adhesive joints using a meshless technique
- 2 August 2023
- Published by Elsevier in Composites Part C: Open Access
- Vol. 12
Open AccessSimulation of mode II fracture propagation in adhesive joints using a meshless technique
- 6 January 2023
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 45 (1) , 1-16
The Ogden model and the natural neighbour radial point interpolation method for hyperelastic analyses
- 6 January 2023
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 45 (1) , 1-16
The Ogden model and the natural neighbour radial point interpolation method for hyperelastic analyses