Mohammad Barzgari
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mohammad Barzgari has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Ali Ghafari
Silicon Integrated, Eindhoven, JW, The Netherlands
2 shared publications Ali Medi
Department of Electrical Engineering and the Faculty of Electrical Engineering, Sharif University of Technology, Tehran, Iran
2 shared publications- Amir Nikpaik
Electrical and Computer Engineering Department, Tarbiat Modares University, Tehran, Iran
1 shared publication - Haibo Yang
Department of Electrical Engineering and Computer Science, Massachusetts Institute of Technology, Cambridge, MA, USA
1 shared publication - Masoud Meghdadi
Faculty of Electrical Engineering, Shahid Beheshti University, Tehran, Iran
1 shared publication - Negar Reiskarimian
Department of Electrical Engineering and Computer Science, Massachusetts Institute of Technology, Cambridge, MA, USA
1 shared publication
Latest Publications
- 31 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (5) , 1726-1737
Gain-Boosted N-Path Receiver With Harmonic Suppression and Scalable Clock Bootstrapping
This work presents a gain-boosted N-path receiver resilient to harmonic blockers by embedding harmonic-reset switching in the feedback path. A three-stage pipeline mixer is used for downconversion, enhancing conversion gain and extending third- and fifth-order harmonic rejection (HR). To reduce power consumption and ensure reliable operation at a 0.6-V supply, a scalable bootstrapped clocking scheme with minimal overhead is introduced. Implemented in 22-nm fully depleted silicon-on-insulator (FD-SOI) technology, the prototype occupies 0.048 mm2, covers 0.25–3 GHz, and achieves 29.5–32-dB gain with a double-sideband (DSB) noise figure (NF) of 3.75–5.3 dB. The receiver (RX) provides input third-order intercept points (IIP3) of +31/+30 dBm and blocker 1-dB (B1dB) compression points of −3/−2 dBm against third- and fifth-order harmonic blockers. Local oscillator (LO) leakage remains below −73 dBm across frequency, while consuming 0.89-mW static power and 1.53-mW/GHz dynamic clock power.
- 31 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (5) , 1726-1737
Gain-Boosted N-Path Receiver With Harmonic Suppression and Scalable Clock Bootstrapping
This work presents a gain-boosted N-path receiver resilient to harmonic blockers by embedding harmonic-reset switching in the feedback path. A three-stage pipeline mixer is used for downconversion, enhancing conversion gain and extending third- and fifth-order harmonic rejection (HR). To reduce power consumption and ensure reliable operation at a 0.6-V supply, a scalable bootstrapped clocking scheme with minimal overhead is introduced. Implemented in 22-nm fully depleted silicon-on-insulator (FD-SOI) technology, the prototype occupies 0.048 mm2, covers 0.25–3 GHz, and achieves 29.5–32-dB gain with a double-sideband (DSB) noise figure (NF) of 3.75–5.3 dB. The receiver (RX) provides input third-order intercept points (IIP3) of +31/+30 dBm and blocker 1-dB (B1dB) compression points of −3/−2 dBm against third- and fifth-order harmonic blockers. Local oscillator (LO) leakage remains below −73 dBm across frequency, while consuming 0.89-mW static power and 1.53-mW/GHz dynamic clock power.
- 15 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (9) , 2672-2684
A Current Re-Use Quadrature RF Receiver Front-End for Low Power Applications: Blixator Circuit
This article presents the theory and implementation of a quadrature and differential RF front-end receiver. Combining balun, low-noise amplifier (LNA), mixer, and oscillator in a single stage, the proposed circuit, named the Blixator, is well suited for low-power applications. The baseband’s transimpedance amplifier (TIA) also shares part of its dc current with the Blixator cell, resulting in sub-milliwatt power consumption. To avoid additional power and area by quadrature LO generation, the I/Q signals are generated at RF, employing the inductors already required for providing the dc current path of the LNA transistors. The expressions for gain, noise figure (NF), and phase noise of the voltage-controlled oscillator (VCO) are derived, and the behavior of the circuit is thoroughly investigated. The prototype of the Blixator receiver is implemented in a 0.18- $\mu \text{m}$ CMOS technology. The experimental results show a NF of 10.5 dB, an IIP3 of −15.5 dBm, at the maximum gain, and an image rejection of 23 dB, which meets the requirements for the Bluetooth Low Energy (BLE) standard. The circuit consumes only 340- $\mu \text{W}$ , from a 0.8-V supply, and its die area is 0.75 mm 2 .
- 15 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (9) , 2672-2684
A Current Re-Use Quadrature RF Receiver Front-End for Low Power Applications: Blixator Circuit
This article presents the theory and implementation of a quadrature and differential RF front-end receiver. Combining balun, low-noise amplifier (LNA), mixer, and oscillator in a single stage, the proposed circuit, named the Blixator, is well suited for low-power applications. The baseband’s transimpedance amplifier (TIA) also shares part of its dc current with the Blixator cell, resulting in sub-milliwatt power consumption. To avoid additional power and area by quadrature LO generation, the I/Q signals are generated at RF, employing the inductors already required for providing the dc current path of the LNA transistors. The expressions for gain, noise figure (NF), and phase noise of the voltage-controlled oscillator (VCO) are derived, and the behavior of the circuit is thoroughly investigated. The prototype of the Blixator receiver is implemented in a 0.18- $\mu \text{m}$ CMOS technology. The experimental results show a NF of 10.5 dB, an IIP3 of −15.5 dBm, at the maximum gain, and an image rejection of 23 dB, which meets the requirements for the Bluetooth Low Energy (BLE) standard. The circuit consumes only 340- $\mu \text{W}$ , from a 0.8-V supply, and its die area is 0.75 mm 2 .
- 18 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (6) , 1594-1609
Even-Harmonic Class-E CMOS Oscillator
This article proposes the theory and implementation of an even-harmonic class-$E$ CMOS oscillator that displays an excellent phase noise performance. Starting from zero voltage switching (ZVS) and zero derivative switching (ZDS) conditions, expressions for drain voltage and current waveforms are derived. Based on a 1:1 transformer, a custom-designed tank is proposed, which satisfies ZVS and ZDS conditions for the core transistors, provides high-$Q$ resonances at both fundamental and second harmonics of the oscillation frequency, and yields a passive voltage gain from the drain to the gate of the core transistors. Satisfying ZVS and ZDS conditions reduces the overlap between the voltage and current waveforms of the transistor that increases the power efficiency of the oscillator. Furthermore, it widens the flat span of the semi half-sinusoidal voltage waveform, where the impulse sensitivity function (ISF) is negligible. Therefore, the conversion of the core transistor noise to phase noise is reduced. These features improve the oscillator’s figure of merit (FoM) in comparison with state-of-the-art CMOS oscillators. The prototype of the even-harmonic class-$E$ oscillator is implemented in a 0.18-$\mu \text{m}$ CMOS technology. At 4 GHz, it exhibits a phase noise of −152.75 dBc/Hz at a 10-MHz offset while providing a 10.6% tuning range. The corresponding FoM is 197.9 dBc/Hz. The circuit draws 7 mA from a 0.7-V supply, and the die area is 0.23 mm2.- 18 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (6) , 1594-1609
Even-Harmonic Class-E CMOS Oscillator
This article proposes the theory and implementation of an even-harmonic class-$E$ CMOS oscillator that displays an excellent phase noise performance. Starting from zero voltage switching (ZVS) and zero derivative switching (ZDS) conditions, expressions for drain voltage and current waveforms are derived. Based on a 1:1 transformer, a custom-designed tank is proposed, which satisfies ZVS and ZDS conditions for the core transistors, provides high-$Q$ resonances at both fundamental and second harmonics of the oscillation frequency, and yields a passive voltage gain from the drain to the gate of the core transistors. Satisfying ZVS and ZDS conditions reduces the overlap between the voltage and current waveforms of the transistor that increases the power efficiency of the oscillator. Furthermore, it widens the flat span of the semi half-sinusoidal voltage waveform, where the impulse sensitivity function (ISF) is negligible. Therefore, the conversion of the core transistor noise to phase noise is reduced. These features improve the oscillator’s figure of merit (FoM) in comparison with state-of-the-art CMOS oscillators. The prototype of the even-harmonic class-$E$ oscillator is implemented in a 0.18-$\mu \text{m}$ CMOS technology. At 4 GHz, it exhibits a phase noise of −152.75 dBc/Hz at a 10-MHz offset while providing a 10.6% tuning range. The corresponding FoM is 197.9 dBc/Hz. The circuit draws 7 mA from a 0.7-V supply, and the die area is 0.23 mm2.