Hassaan Ahmad Butt
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Hassaan Ahmad Butt has a total of 184 co-authors. Here are the top co-authors by number of shared publications:
Zeyu Wang
16 shared publicationsDmitry V. Krasnikov
14 shared publicationsManni Li
12 shared publications- Zeyu Wang
School of Materials Science and Engineering, Jiangsu University, Zhenjiang 212013, China
12 shared publications Vladislav A. Kondrashov
10 shared publications- Albert G. Nasibulin
Skolkovo Institute of Science and Technology
9 shared publications
Latest Publications
- Open Access
- 24 March 2026
- Published by Elsevier in Desalination and Water Treatment
- Vol. 326
Significantly accelerated degradation of naproxen by reduction and complexation coupling in a Cu0/PMS system
- 24 March 2026
- Published by Elsevier in Desalination and Water Treatment
- Vol. 326
Open AccessSignificantly accelerated degradation of naproxen by reduction and complexation coupling in a Cu0/PMS system
- Open Access
- 16 December 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 40, 440-449
The effects of combining thermal, chemical and mechanical treatments on the electrical performance of wet-pulled carbon nanotube fibers
- 16 December 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 40, 440-449
Open AccessThe effects of combining thermal, chemical and mechanical treatments on the electrical performance of wet-pulled carbon nanotube fibers
- 16 November 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (30) , 63112-63125
Electrospun carbon nanofiber membranes as interlayer for acquiring robust Cf/C Composite-GH3536 alloy brazed joints
- 16 November 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (30) , 63112-63125
Electrospun carbon nanofiber membranes as interlayer for acquiring robust Cf/C Composite-GH3536 alloy brazed joints
- 10 October 2025
- Published by Elsevier in Materials Today Communications
- Vol. 49
3D carbon sponge interlayer pyrolysis time control for maximizing Cf/SiC-niobium joint mechanical performance
- 10 October 2025
- Published by Elsevier in Materials Today Communications
- Vol. 49
3D carbon sponge interlayer pyrolysis time control for maximizing Cf/SiC-niobium joint mechanical performance
- 12 July 2025
- Published by Wiley in Polymer Composites
- Vol. 47 (1) , 241-257
Defect‐Independent Multifunctionality Promotion by Single‐Walled Carbon Nanotubes in Hierarchical Carbon Fiber/Thermoset Nanocomposites
Hierarchically reinforced multifunctional nanocomposites are leading‐edge advanced materials. Single‐walled carbon nanotubes (SWCNT) are one of their prime additives, exacerbating functional property development at much lower addition than other carbon allotropes. Here, we prove that SWCNT addition at percolation threshold amounts can provide multifunctional performance regardless of their quality. A plasma etching technique was used to induce SWCNT defectiveness ( I G / I D ratio drops from 66 to 23). These were used to produce SWCNT/carbon fiber/thermoset nanocomposites with concentrations near percolation levels (0.005 wt%). Multifunctional characterization showed that differences in performance were virtually non‐existent. For nanocomposites with additives of different quality, ultimate tensile strength varied between 630 and 645 MPa and flexural strength between 560 and 640 MPa. Both tensile and flexural moduli were within 10% variance. In‐ and through‐plane functional properties, at room and elevated temperature, were also effectively identical. Electrical and thermal conductivity measured up to 150 S cm −1 and 3.7 W(m K) −1 , respectively, while thermal capacity and diffusivity were as high as 1.2 J(g K) −1 and 2.7 mm 2 s −1 . All nanocomposites were thermally stable till ~300°C and microstructural analysis showed no SWCNT‐defect connected effects. Thus, SWCNTs may allow relaxation in typical quality parameters during large‐scale production, reducing current testing and control requirements and thereby, production costs.
- 12 July 2025
- Published by Wiley in Polymer Composites
- Vol. 47 (1) , 241-257
Defect‐Independent Multifunctionality Promotion by Single‐Walled Carbon Nanotubes in Hierarchical Carbon Fiber/Thermoset Nanocomposites
Hierarchically reinforced multifunctional nanocomposites are leading‐edge advanced materials. Single‐walled carbon nanotubes (SWCNT) are one of their prime additives, exacerbating functional property development at much lower addition than other carbon allotropes. Here, we prove that SWCNT addition at percolation threshold amounts can provide multifunctional performance regardless of their quality. A plasma etching technique was used to induce SWCNT defectiveness ( I G / I D ratio drops from 66 to 23). These were used to produce SWCNT/carbon fiber/thermoset nanocomposites with concentrations near percolation levels (0.005 wt%). Multifunctional characterization showed that differences in performance were virtually non‐existent. For nanocomposites with additives of different quality, ultimate tensile strength varied between 630 and 645 MPa and flexural strength between 560 and 640 MPa. Both tensile and flexural moduli were within 10% variance. In‐ and through‐plane functional properties, at room and elevated temperature, were also effectively identical. Electrical and thermal conductivity measured up to 150 S cm −1 and 3.7 W(m K) −1 , respectively, while thermal capacity and diffusivity were as high as 1.2 J(g K) −1 and 2.7 mm 2 s −1 . All nanocomposites were thermally stable till ~300°C and microstructural analysis showed no SWCNT‐defect connected effects. Thus, SWCNTs may allow relaxation in typical quality parameters during large‐scale production, reducing current testing and control requirements and thereby, production costs.