Mohammed K. Gouda
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mohammed K. Gouda has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Saad Ebied
3 shared publications- Salah A. Salman
Mining and Petroleum Department, Faculty of Engineering, Al-Azhar University, Nasr City, Cairo, Egypt
3 shared publications A. Chiba
Institute for Materials Research, Tohoku University, Sendai, Japan
1 shared publicationAkihiko Chiba
1 shared publicationAshraf M. Ashmawy
Department of Chemistry, Faculty of Science, Al-Azhar University, Cairo, Egypt
1 shared publication- Atef Saad Hamada
University of Oulu
1 shared publication
Latest Publications
- Open Access
- 6 September 2022
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 20, 4097-4113
Constitutive modeling and hot deformation processing map of a new biomaterial Ti–14Cr alloy
- 6 September 2022
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 20, 4097-4113
Open AccessConstitutive modeling and hot deformation processing map of a new biomaterial Ti–14Cr alloy
- 1 January 2022
- Published by Springer Nature
- p. 533-555
Sealing Treatments for Electrochemical Conversion Coatings
- 1 January 2022
- Published by Springer Nature
- p. 533-555
Sealing Treatments for Electrochemical Conversion Coatings
- Open Access
- 1 January 2022
- Published by IOP Publishing in Materials Research Express
- Vol. 9 (1) , 015401
Improvement in the microhardness and corrosion behaviour of Ti-14Mn biomedical alloy by cold working
β-titanium alloys are essential in many applications, particularly biomedical applications. Ti-14Mn β-type alloy was produced using an electric arc furnace from raw alloying elements in an inert atmosphere. The alloy was homogenized at 1000 °C for 8 h to ensure the complete composition distribution, followed by solution treatment at 900 °C, then quenched in ice water. The alloy was subjected to cold deformation via cold rolling with different ratios: 10, 30, and 90%. The phases change, microstructure, mechanical properties, and corrosion resistance of Ti-14Mn alloys were evaluated before and after cold rolling. The results showed that the β-phase is the only existed phase even after a high degree of deformation. The microstructure shows a combination of twinning and slipping deformation mechanisms in the deformed alloy. Microhardness values indicated a linear increase equal to 30% by increasing the ratio of cold deformation due to the strain hardening effect. The corrosion resistance of Ti-14Mn alloy was doubled after 90% cold rolling.
- 1 January 2022
- Published by IOP Publishing in Materials Research Express
- Vol. 9 (1) , 015401
Open AccessImprovement in the microhardness and corrosion behaviour of Ti-14Mn biomedical alloy by cold working
β-titanium alloys are essential in many applications, particularly biomedical applications. Ti-14Mn β-type alloy was produced using an electric arc furnace from raw alloying elements in an inert atmosphere. The alloy was homogenized at 1000 °C for 8 h to ensure the complete composition distribution, followed by solution treatment at 900 °C, then quenched in ice water. The alloy was subjected to cold deformation via cold rolling with different ratios: 10, 30, and 90%. The phases change, microstructure, mechanical properties, and corrosion resistance of Ti-14Mn alloys were evaluated before and after cold rolling. The results showed that the β-phase is the only existed phase even after a high degree of deformation. The microstructure shows a combination of twinning and slipping deformation mechanisms in the deformed alloy. Microhardness values indicated a linear increase equal to 30% by increasing the ratio of cold deformation due to the strain hardening effect. The corrosion resistance of Ti-14Mn alloy was doubled after 90% cold rolling.
- 7 December 2021
- Published by SciCell in Acta Metallurgica Slovaca
- Vol. 27 (4) , 180-184
The effect of eggshell as a reinforcement on the mechanical and Corrosion properties of Mg-Zn-Mn matrix composite
Magnesium is a promising lightweight metal required in many industries such as automobile, aerospace, electronics, etc. It is also a biodegradable material, which eliminates the secondary removal procedure of the implant. Furthermore, its mechanical properties are similar to the mechanical properties of human bone. In this research, eggshells were used as an environmentally friendly composite reinforcement material in the Mg-2.5Zn-1Mn matrix. Composites were prepared using the powder metallurgy route. The effect of eggshells on the morphology, mechanical, and corrosion behaviour of Mg-2.5Zn-1Mn alloy was investigated. The results revealed an enhancement in grain refining ability and mechanical properties of Mg-2.5Zn-1Mn with eggshell additives. The corrosion behaviour improved at a higher percentage of eggshells (10%).
- 7 December 2021
- Published by SciCell in Acta Metallurgica Slovaca
- Vol. 27 (4) , 180-184
The effect of eggshell as a reinforcement on the mechanical and Corrosion properties of Mg-Zn-Mn matrix composite
Magnesium is a promising lightweight metal required in many industries such as automobile, aerospace, electronics, etc. It is also a biodegradable material, which eliminates the secondary removal procedure of the implant. Furthermore, its mechanical properties are similar to the mechanical properties of human bone. In this research, eggshells were used as an environmentally friendly composite reinforcement material in the Mg-2.5Zn-1Mn matrix. Composites were prepared using the powder metallurgy route. The effect of eggshells on the morphology, mechanical, and corrosion behaviour of Mg-2.5Zn-1Mn alloy was investigated. The results revealed an enhancement in grain refining ability and mechanical properties of Mg-2.5Zn-1Mn with eggshell additives. The corrosion behaviour improved at a higher percentage of eggshells (10%).
- 2 December 2021
- Published by Springer Nature in Journal of Materials Research
- Vol. 36 (24) , 4883-4893
Biocompatibility and corrosion resistance of low-cost Ti–14Mn–Zr alloys
- 2 December 2021
- Published by Springer Nature in Journal of Materials Research
- Vol. 36 (24) , 4883-4893
Biocompatibility and corrosion resistance of low-cost Ti–14Mn–Zr alloys