Chang-Ping Feng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Chang-Ping Feng has a total of 65 co-authors. Here are the top co-authors by number of shared publications:
Lei Hou
Shandong Engineering Research Center for Additive Manufacturing Qingdao University of Technology Qingdao Shandong China
6 shared publications- Wei Yang
College of Polymer Science and Engineering, Sichuan University, State Key Laboratory of Advanced Polymer Materials, Chengdu, 610065, Sichuan, China
6 shared publications Hong-Bo Lan
Shandong Engineering Research Center for Additive Manufacturing, Qingdao University of Technology, Qingdao 266520, Shandong, People's Republic of China
5 shared publicationsKai-Yin Sun
Shandong Engineering Research Center for Additive Manufacturing, Qingdao University of Technology, Qingdao 266520, Shandong, People's Republic of China
5 shared publicationsGong-Peng Cui
Key Laboratory of Applied Superconductivity, Institute of Electrical Engineering, Chinese Academy of Sciences, Beijing 100190, China
4 shared publicationsJie Yang
College of Polymer Science and Engineering Sichuan University, State Key Laboratory of Polymer Materials Engineering Chengdu People's Republic of China
4 shared publications
Latest Publications
- 6 November 2026
- Published by Wiley in Journal of Applied Polymer Science
Direct‐Write 3D Printing of TIM ‐Free Heat Sinks for Enhanced Chip‐Level Thermal Management
Compared with traditional thermal interface material (TIM) systems, the TIM‐free heat dissipation system proposed in the study removes the separate TIM layer by using a 3D‐printed monolithic structure, thereby reducing the number of thermal interfaces in the heat path. The integrated design allows for custom‐designed, lightweight, and compact structures directly printed onto heat sources, enhancing thermal management efficiency. In this study, we introduce a novel silicone‐based thermal conductive gel, named TIM‐free, achieving a thermal conductivity of up to 1.69 W m −1 K −1 , a total thermal resistance as low as 5.31 × 10 −4 m 2 K W −1 , a storage modulus as low as 392.8 Pa, and an elongation at break of up to 5.44%. Moreover, the TIM‐free gel exhibits excellent printability and can be directly written into 3D heat sink structures. In thermal management tests, the TIM‐free gel was printed directly onto ceramic heaters; compared with setups without any TIM, the temperature of the ceramic heater equipped with the printed TIM‐free heat sink was reduced by 10°C. This approach is particularly suitable for high‐power‐density, next‐generation electronics requiring efficient and space‐saving thermal solutions.
- 6 November 2026
- Published by Wiley in Journal of Applied Polymer Science
Direct‐Write 3D Printing of TIM ‐Free Heat Sinks for Enhanced Chip‐Level Thermal Management
Compared with traditional thermal interface material (TIM) systems, the TIM‐free heat dissipation system proposed in the study removes the separate TIM layer by using a 3D‐printed monolithic structure, thereby reducing the number of thermal interfaces in the heat path. The integrated design allows for custom‐designed, lightweight, and compact structures directly printed onto heat sources, enhancing thermal management efficiency. In this study, we introduce a novel silicone‐based thermal conductive gel, named TIM‐free, achieving a thermal conductivity of up to 1.69 W m −1 K −1 , a total thermal resistance as low as 5.31 × 10 −4 m 2 K W −1 , a storage modulus as low as 392.8 Pa, and an elongation at break of up to 5.44%. Moreover, the TIM‐free gel exhibits excellent printability and can be directly written into 3D heat sink structures. In thermal management tests, the TIM‐free gel was printed directly onto ceramic heaters; compared with setups without any TIM, the temperature of the ceramic heater equipped with the printed TIM‐free heat sink was reduced by 10°C. This approach is particularly suitable for high‐power‐density, next‐generation electronics requiring efficient and space‐saving thermal solutions.
- 24 April 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 14 (35) , 23072-23084
Salt-responsive evaporation behavior of chitosan-based hydrogels: driven by dual-mechanism synergy for efficient seawater desalination
A salt-induced water activation strategy is proposed to develop a highly efficient marine bio-derived chitosan-based hydrogel evaporator featuring reduced crystallinity and anomalous salinity-induced evaporation enhancement.
- 24 April 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 14 (35) , 23072-23084
Salt-responsive evaporation behavior of chitosan-based hydrogels: driven by dual-mechanism synergy for efficient seawater desalination
A salt-induced water activation strategy is proposed to develop a highly efficient marine bio-derived chitosan-based hydrogel evaporator featuring reduced crystallinity and anomalous salinity-induced evaporation enhancement.
- 14 April 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 14 (30) , 19752-19761
3D-printed Bi 2 Te 3 -based thermoelectric devices with phase-change heat sinks: toward efficient energy harvesting and ultra-fast temperature sensing
A DIW-printed out-of-plane Bi 2 Te 3 -based device with a 3D-printed PCM heat sink increased the thermal gradient and boosted output power by 150%. It was integrated into a wireless temperature alarm as a self-powered IoT solution.
- 14 April 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 14 (30) , 19752-19761
3D-printed Bi 2 Te 3 -based thermoelectric devices with phase-change heat sinks: toward efficient energy harvesting and ultra-fast temperature sensing
A DIW-printed out-of-plane Bi 2 Te 3 -based device with a 3D-printed PCM heat sink increased the thermal gradient and boosted output power by 150%. It was integrated into a wireless temperature alarm as a self-powered IoT solution.
- 19 March 2026
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 35 (10) , 1-8
Biologically sourced Enteromorpha polysaccharide-based hydrogel as efficient solar steam generators for solar desalination
- 19 March 2026
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 35 (10) , 1-8
Biologically sourced Enteromorpha polysaccharide-based hydrogel as efficient solar steam generators for solar desalination
- 23 August 2025
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 10 (12) , 11361-11370
3D printing phase-change-based heat sinks for cooling electronic devices
- 23 August 2025
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 10 (12) , 11361-11370
3D printing phase-change-based heat sinks for cooling electronic devices
- 13 August 2025
- Published by Elsevier in Journal of Colloid and Interface Science
- Vol. 701, 138694
3D printable phase change information storage label films for dynamic and multi-level anti-counterfeiting
- 13 August 2025
- Published by Elsevier in Journal of Colloid and Interface Science
- Vol. 701, 138694
3D printable phase change information storage label films for dynamic and multi-level anti-counterfeiting
- 11 February 2025
- Published by Wiley in Polymer Composites
- Vol. 46 (11) , 10187-10196
Scalable thermal interface materials with close‐packed structure and high through‐plane thermal conductivity
Now, composite films exhibiting high in‐plane thermal conductivity have received considerable attention as potential thermal interface materials. However, for real‐world thermal management applications, there is a growing need for soft TIMs with higher through‐plane thermal conductivity. This study is centered on the fabrication of flexible composite film materials with a densely packed filler arrangement using a mass‐producible melt‐processing technique. The composite film is composed of PW/POE as the matrix, spherical Al2O3 as the filler, incorporates high thermal conductivity two‐dimensional fillers BN or GNPs, with graphene nanoplatelets (GNPS) enveloping the surface of the Al2O3 particles to create a closely integrated structure with excellent structural stability. The resulting flexible composite film demonstrates a through‐plane thermal conductivity of 9.24 W/mK and a minimal contact thermal resistance of 2.83 × 10−4 m2·K/W, alongside remarkable flexibility characterized by a low Young's modulus of 0.2 MPa. Experimental demonstrations indicate the robust thermal management potential of the developed composite film, positioning it as a promising solution for advanced electronic packaging technologies.Highlights: The resulting films material has an ideal heat transfer structure. The films exhibit high thermal conductivity and isotropic properties. The films demonstrate outstanding flexibility and sturdy mechanical properties. Higher thermal conductivity does not necessarily improve heat dissipation.
- 11 February 2025
- Published by Wiley in Polymer Composites
- Vol. 46 (11) , 10187-10196
Scalable thermal interface materials with close‐packed structure and high through‐plane thermal conductivity
Now, composite films exhibiting high in‐plane thermal conductivity have received considerable attention as potential thermal interface materials. However, for real‐world thermal management applications, there is a growing need for soft TIMs with higher through‐plane thermal conductivity. This study is centered on the fabrication of flexible composite film materials with a densely packed filler arrangement using a mass‐producible melt‐processing technique. The composite film is composed of PW/POE as the matrix, spherical Al2O3 as the filler, incorporates high thermal conductivity two‐dimensional fillers BN or GNPs, with graphene nanoplatelets (GNPS) enveloping the surface of the Al2O3 particles to create a closely integrated structure with excellent structural stability. The resulting flexible composite film demonstrates a through‐plane thermal conductivity of 9.24 W/mK and a minimal contact thermal resistance of 2.83 × 10−4 m2·K/W, alongside remarkable flexibility characterized by a low Young's modulus of 0.2 MPa. Experimental demonstrations indicate the robust thermal management potential of the developed composite film, positioning it as a promising solution for advanced electronic packaging technologies.Highlights: The resulting films material has an ideal heat transfer structure. The films exhibit high thermal conductivity and isotropic properties. The films demonstrate outstanding flexibility and sturdy mechanical properties. Higher thermal conductivity does not necessarily improve heat dissipation.
- 28 June 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (27) , 35353-35360
3D-printed Bi2Te3-based Thermoelectric Generators for Energy Harvesting and Temperature Response
Thermoelectric generators (TEGs) are environmentally friendly energy harvesting technologies that hold great promise in the field of self-powered electronics and sensing. However, the current development of thermoelectric (TE) devices has largely lagged behind the development of thermoelectric materials, especially in the preparation of thermoelectric components with customizable shapes and excellent properties, which largely limits their practical applications. These issues can be effectively addressed by using 3D printing technology. Here, we print multiple p-type thermoelectric legs (pins) consecutively with this simple technique, and the printed TEGs have excellent thermal potential (288 μV K-1 at room temperature) and excellent temperature response properties, which exhibited an output voltage of 127.94 mV at a temperature difference (ΔT) of 40 K. The 3D-printed thermoelectric generator enables the collection of thermal energy. In addition, the device has excellent temperature sensing characteristics, and this temperature signal to electrical signal conversion is very rapid, which enables temperature sensing alarms in a wide temperature domain. Combining these features, an energy harvesting and electrical alarm concept for home-scale applications is proposed, which is expected to provide a diverse research idea for the application of next-generation thermoelectric devices.
- 28 June 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (27) , 35353-35360
3D-printed Bi2Te3-based Thermoelectric Generators for Energy Harvesting and Temperature Response
Thermoelectric generators (TEGs) are environmentally friendly energy harvesting technologies that hold great promise in the field of self-powered electronics and sensing. However, the current development of thermoelectric (TE) devices has largely lagged behind the development of thermoelectric materials, especially in the preparation of thermoelectric components with customizable shapes and excellent properties, which largely limits their practical applications. These issues can be effectively addressed by using 3D printing technology. Here, we print multiple p-type thermoelectric legs (pins) consecutively with this simple technique, and the printed TEGs have excellent thermal potential (288 μV K-1 at room temperature) and excellent temperature response properties, which exhibited an output voltage of 127.94 mV at a temperature difference (ΔT) of 40 K. The 3D-printed thermoelectric generator enables the collection of thermal energy. In addition, the device has excellent temperature sensing characteristics, and this temperature signal to electrical signal conversion is very rapid, which enables temperature sensing alarms in a wide temperature domain. Combining these features, an energy harvesting and electrical alarm concept for home-scale applications is proposed, which is expected to provide a diverse research idea for the application of next-generation thermoelectric devices.
- 29 January 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (5) , 6025-6032
n-Type PVP/SWCNT Composite Films with Improved Stability for Thermoelectric Power Generation
Single-walled carbon nanotubes (SWCNTs) are one of the promising thermoelectric materials in applications of powering wearable electronics. However, the electrical performance of n-type SWCNTs quickly decreases in air, showing a low stability, and low-cost and effective solutions to improving its stability are also lacking, all of which limit practical applications. In this study, we studied the stability of PVP/SWCNT composite films, where oxygen and moisture from air should be responsible for the decreased stability due to oxidation and hydration. In this case, we found that coating with a 0.20 g mL-1 PVP/0.002 g mL-1 PVDF layer on the surface of PVP/SWCNTs can prevent the penetration of oxygen and moisture from air, improving film stability, where there is almost no reduction in thermoelectric performance after they are exposed to air for 60 days. Based on the stable n-type PVP/SWCNT films, a thermoelectric generator was fabricated, where poly(dimethylsiloxane) (PDMS) was used to coat the surface of the thermoelectric leg to further improve its stability. This generator showed high output performance, which achieved an open-circuit voltage of 10.6 mV and a power density of 312.2 μW cm-2 at a temperature difference of 50 K. Particularly, it exhibited high stability, where the output performance kept almost unchanged after exposure to high-humidity air for 30 days. This coating technology is also applicable to other air-sensitive materials and promotes the development and application of thermoelectric materials and devices.
- 29 January 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (5) , 6025-6032
n-Type PVP/SWCNT Composite Films with Improved Stability for Thermoelectric Power Generation
Single-walled carbon nanotubes (SWCNTs) are one of the promising thermoelectric materials in applications of powering wearable electronics. However, the electrical performance of n-type SWCNTs quickly decreases in air, showing a low stability, and low-cost and effective solutions to improving its stability are also lacking, all of which limit practical applications. In this study, we studied the stability of PVP/SWCNT composite films, where oxygen and moisture from air should be responsible for the decreased stability due to oxidation and hydration. In this case, we found that coating with a 0.20 g mL-1 PVP/0.002 g mL-1 PVDF layer on the surface of PVP/SWCNTs can prevent the penetration of oxygen and moisture from air, improving film stability, where there is almost no reduction in thermoelectric performance after they are exposed to air for 60 days. Based on the stable n-type PVP/SWCNT films, a thermoelectric generator was fabricated, where poly(dimethylsiloxane) (PDMS) was used to coat the surface of the thermoelectric leg to further improve its stability. This generator showed high output performance, which achieved an open-circuit voltage of 10.6 mV and a power density of 312.2 μW cm-2 at a temperature difference of 50 K. Particularly, it exhibited high stability, where the output performance kept almost unchanged after exposure to high-humidity air for 30 days. This coating technology is also applicable to other air-sensitive materials and promotes the development and application of thermoelectric materials and devices.