Onur Erkan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Onur Erkan has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Musa Özkan
University of Warwick 2 School of Engineering Coventry CV4 7AL, United Kingdom
6 shared publications - Sinan Basaran
Bilecik Seyh Edebali University
2 shared publications - Gurbet Çankaya
BİLECİK ŞEYH EDEBALİ ÜNİVERSİTESİ, MÜHENDİSLİK FAKÜLTESİ, MAKİNE MÜHENDİSLİĞİ BÖLÜMÜ
1 shared publication - Muhammad Saif Ullah Khalid
Nature-Inspired Engineering Research Lab (NIERL), Department of Mechanical & Mechatronics Engineering, Lakehead University, Thunder Bay, ON P7B 5E1, Canada
1 shared publication - Yunus Celik
Sivas Bilim ve Teknoloji Universitesi
1 shared publication
Latest Publications
- Open Access
Taguchi-based multi-factor analysis of self-starting behavior in vertical axis wind turbine farms
- 8 January 2024
- Published by Wiley in Energy Technology
- Vol. 12 (4)
Flag Fluttering‐Triggered Piezoelectric Energy Harvester at Low Wind Speed Conditions
Flow‐induced vibrations are common occurrences in various fluid–solid interaction systems existing in nature. One way to transform this vibrational mechanical energy into a usable form is through energy harvesters. This study examines the performance of a piezoelectric energy harvester, where mechanical oscillations result from the fluttering flags made of various fabrics. Flags, made of commonly encountered fabrics, are attached to a cantilever beam inside a wind tunnel with a 30 × 30 cm test section, allowing the airflow to be adjusted between 0 and 10 m s−1. The alpaca flag, with dimensions corresponding to an aspect ratio of 2, can produce meaningful electricity even at a wind speed as low as ≈3.8 m s−1. As the wind speed increases, the fluttering frequency of this flag configuration becomes 10.9 Hz at a wind speed of 5 m s−1, coinciding with the natural frequency of the first mode shape. In this specific arrangement, the structural deformation of the piezoelectric patch on the beam surface is maximized, allowing the harvester system to produce a root mean square voltage of 5 V with a relatively high maximum power of 98 μW.
- 8 January 2024
- Published by Wiley in Energy Technology
- Vol. 12 (4)
Flag Fluttering‐Triggered Piezoelectric Energy Harvester at Low Wind Speed Conditions
Flow‐induced vibrations are common occurrences in various fluid–solid interaction systems existing in nature. One way to transform this vibrational mechanical energy into a usable form is through energy harvesters. This study examines the performance of a piezoelectric energy harvester, where mechanical oscillations result from the fluttering flags made of various fabrics. Flags, made of commonly encountered fabrics, are attached to a cantilever beam inside a wind tunnel with a 30 × 30 cm test section, allowing the airflow to be adjusted between 0 and 10 m s−1. The alpaca flag, with dimensions corresponding to an aspect ratio of 2, can produce meaningful electricity even at a wind speed as low as ≈3.8 m s−1. As the wind speed increases, the fluttering frequency of this flag configuration becomes 10.9 Hz at a wind speed of 5 m s−1, coinciding with the natural frequency of the first mode shape. In this specific arrangement, the structural deformation of the piezoelectric patch on the beam surface is maximized, allowing the harvester system to produce a root mean square voltage of 5 V with a relatively high maximum power of 98 μW.
- 22 August 2023
- Published by Wiley in Energy Technology
- Vol. 11 (10)
Energy Harvesting by V‐Shape Bluff Bodies with Various Apical Angles Attached to a Revolute Joint
This study parametrically investigates the efficiency of an integrated energy harvesting system that consists of a piezoelectric patch attached to a cantilever beam and V‐shape bluff bodies with various apical angles. V‐shape bluff bodies are connected to a cantilever beam with a revolute joint that represents a two degrees‐of‐freedom configuration. The mechanical energy of the galloping and fluttering motions, resulting from the vortex shedding that appears downstream of the bluff bodies, is converted into electricity by means of a piezoelectric patch. The apical angle of the V‐shape geometries, that varies between 0° and 180°, is the main parameter where the generated voltages and the related power curves are the major results for the evaluation of the efficiency of this harvesting system. Based on the experimental examinations, the maximum output power of 0.295 mW is produced at a wind speed of 10 m s−1for the apical angle of 180° and the electrical resistance of 230 kΩ. Moreover, the proposed energy harvester system can still produce usable output power for the apical angles ranges from 0° to 20° and from 170° to 180°.
- 22 August 2023
- Published by Wiley in Energy Technology
- Vol. 11 (10)
Energy Harvesting by V‐Shape Bluff Bodies with Various Apical Angles Attached to a Revolute Joint
This study parametrically investigates the efficiency of an integrated energy harvesting system that consists of a piezoelectric patch attached to a cantilever beam and V‐shape bluff bodies with various apical angles. V‐shape bluff bodies are connected to a cantilever beam with a revolute joint that represents a two degrees‐of‐freedom configuration. The mechanical energy of the galloping and fluttering motions, resulting from the vortex shedding that appears downstream of the bluff bodies, is converted into electricity by means of a piezoelectric patch. The apical angle of the V‐shape geometries, that varies between 0° and 180°, is the main parameter where the generated voltages and the related power curves are the major results for the evaluation of the efficiency of this harvesting system. Based on the experimental examinations, the maximum output power of 0.295 mW is produced at a wind speed of 10 m s−1for the apical angle of 180° and the electrical resistance of 230 kΩ. Moreover, the proposed energy harvester system can still produce usable output power for the apical angles ranges from 0° to 20° and from 170° to 180°.
- 1 January 2022
- Published by Elsevier in Renewable Energy
- Vol. 184, 421-429
Control of a boundary layer over a wind turbine blade using distributed passive roughness
- 1 January 2022
- Published by Elsevier in Renewable Energy
- Vol. 184, 421-429
Control of a boundary layer over a wind turbine blade using distributed passive roughness
- 28 June 2020
- Published by Bilecik Seyh Edebali Universitesi Fen Bilimleri Dergisi in Bilecik Şeyh Edebali Üniversitesi Fen Bilimleri Dergisi
- Vol. 7 (1) , 461-472
Numerical Investigation of Active Control of Boundary Layer Flow Around S809 Airfoil with Suction Method
Bu çalışmada, sınır tabaka akışı aktif kontrol yöntemlerinden biri olan, sınır tabakadan kanat içerisine hava emilmesi prensibine dayanan emme tekniği kullanılarak bir rüzgar türbini kanadının aerodinamik performansının arttırılması hedeflenmiştir. Emme işlemi daimi bir jet vasıtasıyla gerçekleştirilmiş, kanat modeli olarak rüzgar türbini uygulamalarında yaygın olarak kullanılan S809 kanat profili tercih edilmiştir. Çalışma parametreleri olarak, üç ayrı jet konumu (Ljet = 0.1c, 0.26c, 0.36c) ve üç ayrı jet oranı (Rjet = 0.1, 0.3, 0.5) seçilmiştir. Emme jeti genişliği sabit olup veter uzunluğunun %2.5’i kadar ve emme jeti açısı (θjet) bölgesel jet yüzeyine 90° olacak şekilde ayarlanmıştır. İki boyutlu türbülanslı akış için sayısal analiz; α = 15° hücum açısında ve Re = 106’da SST k-ω türbülans modeli kullanılarak gerçekleştirilmiştir. İlk olarak emme jeti konumunun etkisi, ardından en iyi sonucu veren emme jeti konumu seçilerek emme jeti oranının etkisi araştırılmıştır. Kanat profili etrafındaki akışa ait simülasyon sonuçları incelendiğinde, en iyi sonuç emme jeti konumu 0.36c (Jet-3) ve emme jeti oranı 0.5 olduğunda alınmıştır. Jet kullanılmadığı duruma göre CL/CD oranı 17.92’den 273.03’e yükselmiştir. Emme jeti ile kontrol yönteminin uygulanması ile kontrolsüz duruma göre Cl değeri yaklaşık olarak 1.211’den 1.8’e yükselmiş, Cd değeri ise 0.068’den 0.0066’ya düşmüştür.
- 28 June 2020
- Published by Bilecik Seyh Edebali Universitesi Fen Bilimleri Dergisi in Bilecik Şeyh Edebali Üniversitesi Fen Bilimleri Dergisi
- Vol. 7 (1) , 461-472
Numerical Investigation of Active Control of Boundary Layer Flow Around S809 Airfoil with Suction Method
Bu çalışmada, sınır tabaka akışı aktif kontrol yöntemlerinden biri olan, sınır tabakadan kanat içerisine hava emilmesi prensibine dayanan emme tekniği kullanılarak bir rüzgar türbini kanadının aerodinamik performansının arttırılması hedeflenmiştir. Emme işlemi daimi bir jet vasıtasıyla gerçekleştirilmiş, kanat modeli olarak rüzgar türbini uygulamalarında yaygın olarak kullanılan S809 kanat profili tercih edilmiştir. Çalışma parametreleri olarak, üç ayrı jet konumu (Ljet = 0.1c, 0.26c, 0.36c) ve üç ayrı jet oranı (Rjet = 0.1, 0.3, 0.5) seçilmiştir. Emme jeti genişliği sabit olup veter uzunluğunun %2.5’i kadar ve emme jeti açısı (θjet) bölgesel jet yüzeyine 90° olacak şekilde ayarlanmıştır. İki boyutlu türbülanslı akış için sayısal analiz; α = 15° hücum açısında ve Re = 106’da SST k-ω türbülans modeli kullanılarak gerçekleştirilmiştir. İlk olarak emme jeti konumunun etkisi, ardından en iyi sonucu veren emme jeti konumu seçilerek emme jeti oranının etkisi araştırılmıştır. Kanat profili etrafındaki akışa ait simülasyon sonuçları incelendiğinde, en iyi sonuç emme jeti konumu 0.36c (Jet-3) ve emme jeti oranı 0.5 olduğunda alınmıştır. Jet kullanılmadığı duruma göre CL/CD oranı 17.92’den 273.03’e yükselmiştir. Emme jeti ile kontrol yönteminin uygulanması ile kontrolsüz duruma göre Cl değeri yaklaşık olarak 1.211’den 1.8’e yükselmiş, Cd değeri ise 0.068’den 0.0066’ya düşmüştür.
- Open Access
- 1 April 2020
- Published by Black Sea Journal of Engineering and Science in Black Sea Journal of Engineering and Science
- Vol. 3 (2) , 50-56
Investigation of the Flow Over NACA 63-415 Airfoil
In this article, a two-dimensional, incompressible flow around a NACA 63-415 airfoil, which is widely used as one of the commercial wind turbine blade profiles, is investigated. The goal of this research is to obtain the optimum angle of attack for this particular type of airfoil within a precise range. The Reynolds-Averaged Navier-Stokes (RANS) technique of Computational Fluid Dynamics (CFD) has been employed to examine the flow where the Reynolds number is in the range of 105 to 3x106 and also for the angles of attack from 0° to 20°. These are the typical flow conditions mostly encountered in the real applications of wind turbine blades. The turbulent flow is modelled by means of the Spalart-Allmaras turbulence model since its capability of simulating aerodynamic flows. The ratio of the lift force to the drag force acting on the airfoil has been chosen as a control parameter since the lift force increases the power generated by the turbine, whereas the drag force negatively affects the performance. The present numerical result shows that the maximum lift to drag ratio is observed between 2.5° and 3.5°, depending on the Reynolds number.
- 1 April 2020
- Published by Black Sea Journal of Engineering and Science in Black Sea Journal of Engineering and Science
- Vol. 3 (2) , 50-56
Open AccessInvestigation of the Flow Over NACA 63-415 Airfoil
In this article, a two-dimensional, incompressible flow around a NACA 63-415 airfoil, which is widely used as one of the commercial wind turbine blade profiles, is investigated. The goal of this research is to obtain the optimum angle of attack for this particular type of airfoil within a precise range. The Reynolds-Averaged Navier-Stokes (RANS) technique of Computational Fluid Dynamics (CFD) has been employed to examine the flow where the Reynolds number is in the range of 105 to 3x106 and also for the angles of attack from 0° to 20°. These are the typical flow conditions mostly encountered in the real applications of wind turbine blades. The turbulent flow is modelled by means of the Spalart-Allmaras turbulence model since its capability of simulating aerodynamic flows. The ratio of the lift force to the drag force acting on the airfoil has been chosen as a control parameter since the lift force increases the power generated by the turbine, whereas the drag force negatively affects the performance. The present numerical result shows that the maximum lift to drag ratio is observed between 2.5° and 3.5°, depending on the Reynolds number.