John Dudgeon
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
John Dudgeon has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Chikashi Sato
Department of Civil and Environmental Engineering, Idaho State University, 921 S. 8th Ave., Stop 8060, Pocatello, ID 83209, USA
3 shared publications - Noris Evelin Paucar
Department of Civil and Environmental Engineering, Idaho State University, 921 South 8th Avenue, Stop 8060, Pocatello, ID 83209, USA
2 shared publications - Wilgince Apollon
Centro de Investigación en Ciencia Aplicada y Tecnología Avanzada (CICATA), Instituto Politécnico Nacional (IPN), Carretera Tampico‐Puerto Industrial Altamira km 14.5, C. Manzano, Industrial Altamira Altamira Mexico
2 shared publications - Alejandro Isabel Luna-Maldonado
Department of Agricultural and Food Engineering, Faculty of Agriculture, Autonomous University of Nuevo Leon, Nuevo Leon, Mexico
1 shared publication - Ghazaleh Alikaram
Department of Civil and Environmental Engineering, Idaho State University, 921 S. 8th Ave., Stop 8060, Pocatello, ID 83209, USA
1 shared publication - Monte Hibbert
Department of Civil and Environmental Engineering, Idaho State University, 921 South 8th Avenue, Stop 8060, Pocatello, ID 83209, USA
1 shared publication
Latest Publications
- Open Access
An Algae Cultivator Coupled with a Hybrid Photosynthetic–Air-Cathode Microbial Fuel Cell with Ceramic Membrane Interface
Microalgae are promising candidates for renewable biofuel production and nutrient-rich animal feed. Cultivating microalgae using wastewater can lower production costs but often results in biomass contamination and increases downstream processing requirements. This study presents a novel system that integrates an algae cultivator (AC) with a single-chamber microbial fuel cell (MFC) equipped with photosynthetic and air-cathode functionalities, separated by a ceramic membrane. The system enables the generation of electricity and production of clean microalgae biomass concurrently, in both light and dark conditions, utilizing wastewater as a nutrient source and renewable energy. The MFC chamber was filled with simulated potato processing wastewater, while the AC chamber contained microalgae Chlorella vulgaris in a growth medium. The ceramic membrane allowed nutrient diffusion while preventing direct contact between algae and wastewater. This design effectively supported algal growth and produced uncontaminated, harvestable biomass. At the same time, larger particulates and undesirable substances were retained in the MFC. The system can be operated with synergy between the MFC and AC systems, reducing operational and pretreatment costs. Overall, this hybrid design highlights a sustainable pathway for integrating electricity generation, nutrient recovery, and algae-based biofuel feedstock production, with improved economic feasibility due to high-quality biomass cultivation and the ability to operate continuously under variable lighting conditions.
Open AccessAn Algae Cultivator Coupled with a Hybrid Photosynthetic–Air-Cathode Microbial Fuel Cell with Ceramic Membrane Interface
Microalgae are promising candidates for renewable biofuel production and nutrient-rich animal feed. Cultivating microalgae using wastewater can lower production costs but often results in biomass contamination and increases downstream processing requirements. This study presents a novel system that integrates an algae cultivator (AC) with a single-chamber microbial fuel cell (MFC) equipped with photosynthetic and air-cathode functionalities, separated by a ceramic membrane. The system enables the generation of electricity and production of clean microalgae biomass concurrently, in both light and dark conditions, utilizing wastewater as a nutrient source and renewable energy. The MFC chamber was filled with simulated potato processing wastewater, while the AC chamber contained microalgae Chlorella vulgaris in a growth medium. The ceramic membrane allowed nutrient diffusion while preventing direct contact between algae and wastewater. This design effectively supported algal growth and produced uncontaminated, harvestable biomass. At the same time, larger particulates and undesirable substances were retained in the MFC. The system can be operated with synergy between the MFC and AC systems, reducing operational and pretreatment costs. Overall, this hybrid design highlights a sustainable pathway for integrating electricity generation, nutrient recovery, and algae-based biofuel feedstock production, with improved economic feasibility due to high-quality biomass cultivation and the ability to operate continuously under variable lighting conditions.
- Open Access
Integrating Microbial Fuel Cell and Hydroponic Technologies Using a Ceramic Membrane Separator to Develop an Energy–Water–Food Supply System
In this study, a microbial fuel cell was integrated into a hydroponic system (MFC-Hyp) using a ceramic membrane as a separator. The MFC-Hyp is a passive system that allows the transport of nutrients from wastewater in the microbial fuel cell (MFC) to water in the hydroponic vessel (Hyp) through a ceramic membrane separator, with no external energy input. The performance of this system was examined using potato-process wastewater as a source of energy and nutrients (K, P, N) and garlic chives (Allium tuberosum) as a hydroponic plant. The results showed that based on dry weight, the leaves of Allium tuberosum grew 142% more in the MFC-Hyp than those of the plant in the Hyp without the MFC, in a 49-day run. The mass fluxes of K, P, and NO3−-N from the MFC to the Hyp through the ceramic membrane were 4.18 ± 0.70, 3.78 ± 1.90, and 2.04 ± 0.98 µg s−1m−2, respectively. It was apparent that the diffusion of nutrients from wastewater in the MFC enhanced the plant growth in the Hyp. The MFC-Hyp in the presence of A. tuberosum produced the maximum power density of 130.2 ± 45.4 mW m−2. The findings of this study suggest that the MFC-Hyp system has great potential to be a “carbon-neutral” technology that could be transformed into an important part of a diversified worldwide energy–water–food supply system.
Open AccessIntegrating Microbial Fuel Cell and Hydroponic Technologies Using a Ceramic Membrane Separator to Develop an Energy–Water–Food Supply System
In this study, a microbial fuel cell was integrated into a hydroponic system (MFC-Hyp) using a ceramic membrane as a separator. The MFC-Hyp is a passive system that allows the transport of nutrients from wastewater in the microbial fuel cell (MFC) to water in the hydroponic vessel (Hyp) through a ceramic membrane separator, with no external energy input. The performance of this system was examined using potato-process wastewater as a source of energy and nutrients (K, P, N) and garlic chives (Allium tuberosum) as a hydroponic plant. The results showed that based on dry weight, the leaves of Allium tuberosum grew 142% more in the MFC-Hyp than those of the plant in the Hyp without the MFC, in a 49-day run. The mass fluxes of K, P, and NO3−-N from the MFC to the Hyp through the ceramic membrane were 4.18 ± 0.70, 3.78 ± 1.90, and 2.04 ± 0.98 µg s−1m−2, respectively. It was apparent that the diffusion of nutrients from wastewater in the MFC enhanced the plant growth in the Hyp. The MFC-Hyp in the presence of A. tuberosum produced the maximum power density of 130.2 ± 45.4 mW m−2. The findings of this study suggest that the MFC-Hyp system has great potential to be a “carbon-neutral” technology that could be transformed into an important part of a diversified worldwide energy–water–food supply system.
- Open Access
Single-Chamber Microbial Fuel Cell with Multiple Plates of Bamboo Charcoal Anode: Performance Evaluation
In this study, three single-chamber microbial fuel cells (MFCs), each having Pt-coated carbon cloth as a cathode and four bamboo charcoal (BC) plates as an anode, were run in a fed-batch mode, individually and in series. Simulated potato-processing wastewater was used as a substrate for supporting the growth of a mixed bacterial culture. The maximum power output increased from 0.386 mW with one MFC to 1.047 mW with three MFCs connected in series. The maximum power density, however, decreased from 576 mW/m2 (normalized to the cathode area) with one MFC to 520 mW/m2 with three MFCs in series. The experimental results showed that power can be increased by connecting the MFCs in series; however, choosing low resistance BC is crucial for increasing power density.
Open AccessSingle-Chamber Microbial Fuel Cell with Multiple Plates of Bamboo Charcoal Anode: Performance Evaluation
In this study, three single-chamber microbial fuel cells (MFCs), each having Pt-coated carbon cloth as a cathode and four bamboo charcoal (BC) plates as an anode, were run in a fed-batch mode, individually and in series. Simulated potato-processing wastewater was used as a substrate for supporting the growth of a mixed bacterial culture. The maximum power output increased from 0.386 mW with one MFC to 1.047 mW with three MFCs connected in series. The maximum power density, however, decreased from 576 mW/m2 (normalized to the cathode area) with one MFC to 520 mW/m2 with three MFCs in series. The experimental results showed that power can be increased by connecting the MFCs in series; however, choosing low resistance BC is crucial for increasing power density.