Carl Labergere
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Carl Labergere has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Khemais Saanouni
ICD-LASMIS, University of Technology of Troyes
7 shared publications - Houssem Badreddine
Université de Technologie de Troyes
5 shared publications - Pascal Lafon
LASMIS, Université de Technologie de Troyes, Troyes, France
3 shared publications - A. Rassineux
University of technology of Compiegne, Laboratoire Roberval, UMR CNRS 6253, centre de Recherche de Royallieu
2 shared publications - Alain Rassineux
Université de Technologie de Compiègne, LG2MS, U.R.A. CNRS 1505 BP529 F‐60205 Compiègne Cedex, France
2 shared publications - Mohamed Hamed
University of Technology of Troyes
2 shared publications
Latest Publications
- Open Access
- 15 April 2026
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 388, 127-140
Stochastic Forming Limit Curves: Construction of a Probabilistic Tool for Failure Assessment
The determination of Forming Limit Curves (FLCs) remains challenging due to their strong dependence on test conditions, material properties, and measurement methods. Significant variability is observed even for identical specimens, limiting the reliability of FLCs as deterministic tools. The goal of this work is to investigate non-deterministic FLC prediction in order to illustrate the impact of uncertainties and provide a basis for quantification of failure risks. The proposed approach uses the probabilistic framework where a model of input uncertainties including dependence is inferred from literature data using a Gaussian copula. A prediction model based on the linear perturbation technique is described and used to propagateinput uncertainties using a Monte-Carlo approach. The obtained stochastic FLC is illustrated in terms of empirical confidence areas.
- 15 April 2026
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 388, 127-140
Open AccessStochastic Forming Limit Curves: Construction of a Probabilistic Tool for Failure Assessment
The determination of Forming Limit Curves (FLCs) remains challenging due to their strong dependence on test conditions, material properties, and measurement methods. Significant variability is observed even for identical specimens, limiting the reliability of FLCs as deterministic tools. The goal of this work is to investigate non-deterministic FLC prediction in order to illustrate the impact of uncertainties and provide a basis for quantification of failure risks. The proposed approach uses the probabilistic framework where a model of input uncertainties including dependence is inferred from literature data using a Gaussian copula. A prediction model based on the linear perturbation technique is described and used to propagateinput uncertainties using a Monte-Carlo approach. The obtained stochastic FLC is illustrated in terms of empirical confidence areas.
- 20 September 2023
- Published by Springer Nature
- p. 171-182
A Methodology Using Cycle Jump Algorithm for Prediction of the Low Cycle Fatigue Life Concerning Mechanical Structures
- 20 September 2023
- Published by Springer Nature
- p. 171-182
A Methodology Using Cycle Jump Algorithm for Prediction of the Low Cycle Fatigue Life Concerning Mechanical Structures
- 1 December 2021
- Published by SAGE Publications in International Journal of Damage Mechanics
- Vol. 31 (5) , 723-761
Modeling and simulation of ductile damage in forged steel used to encapsulate high-level radioactive waste
Andra, the French national radioactive waste management agency, is in charge of studying the disposal of high-level and long-lived intermediate-level waste (HLW and ILW-LL) in a deep geological repository. According to the reference concept, it is planned to encapsulate high-level waste in non-alloy P285NH steel overpacks before inserting them into horizontal steel cased micro-tunnels. This work is a part of the study about the long-term behavior of a welded steel overpack subjected to external hydrostatic pressure and several localized loading paths. Indeed, the main objective of this work is to develop the most suitable model for non-alloy steel P285NH to be used in the prediction of the long-term overpack behavior. Dealing with a ductile steel, elastoplastic constitutive equations accounting for mixed nonlinear isotropic and kinematic hardening strongly coupled with ductile isotropic damage are adopted. They are formulated based on the classical thermodynamics of irreversible processes framework with state variables at the macroscopic scale, (Germain, 1973) (Lemaitre 1985, Saanouni 2012). In this paper, a new coupling formulation between the scalar isotropic ductile damage and the deviatoric and spherical part of the Cauchy stress and elastic strain tensors is proposed. In order to calibrate the developed model on P285NH steel, multiple tensile tests are performed using classical cylindrical specimens, notched specimens and double notched specimens. In the last part, some experimental fields are measured using digital image correlation. Application is made to a simplified overpack represented by thick walled cylinder subject to compressive loading path. A FEM (Finite Element method) crushing operation of an overpack’s cylindrical part has simulated and analysed.
- 1 December 2021
- Published by SAGE Publications in International Journal of Damage Mechanics
- Vol. 31 (5) , 723-761
Modeling and simulation of ductile damage in forged steel used to encapsulate high-level radioactive waste
Andra, the French national radioactive waste management agency, is in charge of studying the disposal of high-level and long-lived intermediate-level waste (HLW and ILW-LL) in a deep geological repository. According to the reference concept, it is planned to encapsulate high-level waste in non-alloy P285NH steel overpacks before inserting them into horizontal steel cased micro-tunnels. This work is a part of the study about the long-term behavior of a welded steel overpack subjected to external hydrostatic pressure and several localized loading paths. Indeed, the main objective of this work is to develop the most suitable model for non-alloy steel P285NH to be used in the prediction of the long-term overpack behavior. Dealing with a ductile steel, elastoplastic constitutive equations accounting for mixed nonlinear isotropic and kinematic hardening strongly coupled with ductile isotropic damage are adopted. They are formulated based on the classical thermodynamics of irreversible processes framework with state variables at the macroscopic scale, (Germain, 1973) (Lemaitre 1985, Saanouni 2012). In this paper, a new coupling formulation between the scalar isotropic ductile damage and the deviatoric and spherical part of the Cauchy stress and elastic strain tensors is proposed. In order to calibrate the developed model on P285NH steel, multiple tensile tests are performed using classical cylindrical specimens, notched specimens and double notched specimens. In the last part, some experimental fields are measured using digital image correlation. Application is made to a simplified overpack represented by thick walled cylinder subject to compressive loading path. A FEM (Finite Element method) crushing operation of an overpack’s cylindrical part has simulated and analysed.
- Open Access
- 30 May 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (11) , 5075
A Finite Element Method to Predict the Mechanical Behavior of a Pre-Structured Material Manufactured by Fused Filament Fabrication in 3D Printing
In this paper, a numerical method is proposed to simulate the mechanical behavior of a new polymeric pre-structured material manufactured by fused filament fabrication (FFF), where the filaments are oriented along the principal stress directions. The model implements optimized filament orientations, obtained from the G code by assigning materials references in mesh elements. The Gauss points are later configured with the physical behavior while considering a homogeneous solid structure. The objective of this study is to identify the elastoplastic behavior. Therefore, tensile tests were conducted with different filament orientations. The results show that using appropriate material constants is efficient in describing the built anisotropy and incorporating the air gap volume fraction. The suggested method is proved very efficient in implementing multiplex G code orientations. The elastic behavior of the pre-structured material is quasi-isotropic. However, the anisotropy was observed at the yield point and the ultimate stress. Using the Hill criterion coupled with an experimental tabular law of the plastic flow turns out to be suitable for predicting the response of various specimens.
- 30 May 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (11) , 5075
Open AccessA Finite Element Method to Predict the Mechanical Behavior of a Pre-Structured Material Manufactured by Fused Filament Fabrication in 3D Printing
In this paper, a numerical method is proposed to simulate the mechanical behavior of a new polymeric pre-structured material manufactured by fused filament fabrication (FFF), where the filaments are oriented along the principal stress directions. The model implements optimized filament orientations, obtained from the G code by assigning materials references in mesh elements. The Gauss points are later configured with the physical behavior while considering a homogeneous solid structure. The objective of this study is to identify the elastoplastic behavior. Therefore, tensile tests were conducted with different filament orientations. The results show that using appropriate material constants is efficient in describing the built anisotropy and incorporating the air gap volume fraction. The suggested method is proved very efficient in implementing multiplex G code orientations. The elastic behavior of the pre-structured material is quasi-isotropic. However, the anisotropy was observed at the yield point and the ultimate stress. Using the Hill criterion coupled with an experimental tabular law of the plastic flow turns out to be suitable for predicting the response of various specimens.
- 31 January 2020
- Published by Springer Nature in Acta Mechanica
- Vol. 231 (5) , 1731-1749
Investigation on a full coupling between damage and other thermomechanical behaviours in the standard thermodynamic framework including environmental effects
- 31 January 2020
- Published by Springer Nature in Acta Mechanica
- Vol. 231 (5) , 1731-1749
Investigation on a full coupling between damage and other thermomechanical behaviours in the standard thermodynamic framework including environmental effects
- 5 October 2018
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 19 (10) , 1545-1551
Mechanical Behavior of Embossed AA1050-O Sheets Subjected to Tension and Forming
- 5 October 2018
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 19 (10) , 1545-1551
Mechanical Behavior of Embossed AA1050-O Sheets Subjected to Tension and Forming
- 6 August 2018
- Published by Springer Nature in International Journal of Material Forming
- Vol. 12 (4) , 535-552
Adaptive metamodel-assisted shape optimization for springback in metal forming processes
- 6 August 2018
- Published by Springer Nature in International Journal of Material Forming
- Vol. 12 (4) , 535-552
Adaptive metamodel-assisted shape optimization for springback in metal forming processes
- 4 September 2014
- Published by Springer Nature
- p. 815-875
Ductile Damage in Metal Forming: Advanced Macroscopic Modeling and Numerical Simulation
- 4 September 2014
- Published by Springer Nature
- p. 815-875
Ductile Damage in Metal Forming: Advanced Macroscopic Modeling and Numerical Simulation
- 17 July 2014
- Published by SAGE Publications in International Journal of Damage Mechanics
- Vol. 23 (8) , 1055-1076
Multi-objective optimization based on meta-models of an aeronautical hub including the ductile damage constraint
In forging process, geometric design of initial billet and tools is very important. Traditionally, engineers use their knowledge and experience to design and optimize the geometric model of forging process by using trial-and-error methods. Such methods are time consuming and cost expensive. It is therefore interesting to design an automatic tools builder based on optimization methodology coupled with virtual finite element simulations, thus helping engineers to improve products and reduce cost. In this article we describe a meta-model based multi-objective optimization methodology for forging process designed to build the theoric Pareto optimal front of the mechanical problem. We go through a four-step process: building parametric computer-aided design geometry model, simulating the forging process according to the DOE, fitting meta-models, and optimizing the process by using an advanced algorithm. Two different meta-models, including polynomial and kriging methods, are constructed, based on the simulation values for different responses. Then optimization algorithms NBI-NLPQLP and NSGA-II are applied to find the optimum solutions based on each different meta-model. In order to drive this procedure automatically we use ModeFRONTIER® software. Using this environment, several macro commands are used to connect the geometry modelling (made with CATIA V5™) and numerical simulation process. As an industrial example, a two-step forging of an aeronautic component shows the efficiency of the proposed methodology. That shows contributions of research in dealing with optimization design of die geometry taking into account technological interactions related to the process and the ductile damage inside the deformed part. A set of solutions selected in particular points of the optimal Pareto front are also presented and analysed.
- 17 July 2014
- Published by SAGE Publications in International Journal of Damage Mechanics
- Vol. 23 (8) , 1055-1076
Multi-objective optimization based on meta-models of an aeronautical hub including the ductile damage constraint
In forging process, geometric design of initial billet and tools is very important. Traditionally, engineers use their knowledge and experience to design and optimize the geometric model of forging process by using trial-and-error methods. Such methods are time consuming and cost expensive. It is therefore interesting to design an automatic tools builder based on optimization methodology coupled with virtual finite element simulations, thus helping engineers to improve products and reduce cost. In this article we describe a meta-model based multi-objective optimization methodology for forging process designed to build the theoric Pareto optimal front of the mechanical problem. We go through a four-step process: building parametric computer-aided design geometry model, simulating the forging process according to the DOE, fitting meta-models, and optimizing the process by using an advanced algorithm. Two different meta-models, including polynomial and kriging methods, are constructed, based on the simulation values for different responses. Then optimization algorithms NBI-NLPQLP and NSGA-II are applied to find the optimum solutions based on each different meta-model. In order to drive this procedure automatically we use ModeFRONTIER® software. Using this environment, several macro commands are used to connect the geometry modelling (made with CATIA V5™) and numerical simulation process. As an industrial example, a two-step forging of an aeronautic component shows the efficiency of the proposed methodology. That shows contributions of research in dealing with optimization design of die geometry taking into account technological interactions related to the process and the ductile damage inside the deformed part. A set of solutions selected in particular points of the optimal Pareto front are also presented and analysed.