MVMathias Vang

Mathias Vang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mathias Vang has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Use of on-time gates to determine relative transmitter–receiver separation for transient electromagnetic systems with a single-component transmitter and receiver

    by Denys Grombacher, Matthew Griffiths, Mathias Østbjerg Vang, Pradip Maurya

    An approach to dynamically determine the separation between transmit and receive coils in electromagnetic systems based upon measurement of the primary field induced voltages was presented. This approach proposes an adaptation of primary-field-based localization schemes suitable for a two-horizontal-coil setup common to many ground-based or towed transient electromagnetic platforms. It was shown that the dominant influence on primary field induced voltages was radial displacements and that neglecting other tangential displacements and/or rotation effects introduced only minor offset biases in an approach that assumed a radial offset was solely responsible for the on-time voltages. Secondary fields produced by a conductive earth were shown to perturb on-time measurements during intervals of rapid current change in the transmit loop, and recommendations for reducing these influences were discussed. Field results indicated a 10 s of centimeters localization of the receiver can be achieved for offsets up to 20 m.

  • Open Access

    Alleviating interpretational ambiguity in hydrogeology through clustering-based analysis of transient electromagnetic and surface nuclear magnetic resonance data

    by Mathias Vang, Jakob Juul Larsen, Anders Vest Christiansen, Denys Grombacher

    Local characterization of groundwater systems is critical for managing and protecting vulnerable resources. Geophysical methods can provide dense imaging of subsurface parameters to delineate lithological boundaries and water tables for hydrogeological investigation, though using a single geophysical method for determining lithologies can yield erroneous interpretations as different lithologies can have similar properties. By using several geophysical methods, it is possible to reduce this risk and better assign likely lithologies to subsurface units. We present two case studies where transient electromagnetics (TEM) and surface nuclear magnetic resonance (SNMR) are used in combination to delineate hydrogeological structures. Novel spatially constrained inversion in SNMR was used to provide horizontal consistency between soundings. Three coincident parameters, resistivity from the TEM measurements and water content and relaxation time from the SNMR measurements, were used in a K-means clustering scheme to resolve subsurface structures. The K-means clustering was evaluated with a silhouette index to pick the number of clusters. After clustering, each cluster was assigned a hydrogeological description based on the distinct features in the three parameters; e.g., a low resistivity, high water content, and high T2∗ are assigned as saltwater-saturated sand. In the first case study, the clusters enabled improved resolution of a regional water table in an unconfined aquifer setting with the multi-geophysical approach. The water table estimates were positively evaluated against multiple boreholes within 500 m of coincident geophysical models. The second case study illustrates how clustering, of SNMR and TEM models, can delineate saltwater intrusion in an island coastal aquifer, which would not be possible with any of these methods individually. Additionally, the clustering resolved the main shallow aquifer on the island. Our work illustrates how the combination of geophysical data can be used to improve the identification of hydrogeological layers and reduce interpretational bias.

  • Open Access

    Reply on RC1

    by Mathias Vang, Jakob Juul Larsen, Anders Vest Christiansen, Denys Grombacher

    Local characterization of groundwater systems is critical for managing and protecting vulnerable resources. Geophysical methods can provide dense imaging of subsurface parameters to delineate lithological boundaries and water tables for hydrogeological investigation. Though, using a single geophysical method for determining lithologies can yield erroneous interpretations as different lithologies can have similar properties. By using several geophysical methods, it is possible to reduce this risk and better assign likely lithologies to subsurface units. We present two case studies where transient electromagnetic (TEM) and surface nuclear magnetic resonance (SNMR) are used in combination to delineate hydrogeological structures. Novel spatially constrained inversion in SNMR was used to provide horizontal consistency between soundings. Three coincident parameters, resistivity from the TEM measurements and water content and relaxation time from the SNMR measurements were used in a K-means clustering scheme to resolve subsurface structures. The K-means clustering was evaluated with a silhouette index to pick the number of clusters. After clustering, each cluster was assigned a hydrogeological description based on the distinct features in the three parameters, e.g. a low resistivity, high water content, and high T2* is assigned as saltwater saturated sand. In the first case study, the clusters enabled improved resolution of a regional water table in an unconfined aquifer setting by the multi-geophysical approach. The water table estimates were positively evaluated against multiple boreholes within 500 m of coincident geophysical models. The second case study illustrates how clustering, of SNMR and TEM models, can delineate saltwater intrusion in an island coastal aquifer, which would not be possible with any of these methods individually. Additionally, the clustering resolved the main shallow aquifer on the island. Our work illustrates how the combination of geophysical data can be used to improve resolution of hydrogeological layers and reduce interpretational bias.

  • Open Access

    Reply on RC2

    by Mathias Vang, Jakob Juul Larsen, Anders Vest Christiansen, Denys Grombacher

    Local characterization of groundwater systems is critical for managing and protecting vulnerable resources. Geophysical methods can provide dense imaging of subsurface parameters to delineate lithological boundaries and water tables for hydrogeological investigation. Though, using a single geophysical method for determining lithologies can yield erroneous interpretations as different lithologies can have similar properties. By using several geophysical methods, it is possible to reduce this risk and better assign likely lithologies to subsurface units. We present two case studies where transient electromagnetic (TEM) and surface nuclear magnetic resonance (SNMR) are used in combination to delineate hydrogeological structures. Novel spatially constrained inversion in SNMR was used to provide horizontal consistency between soundings. Three coincident parameters, resistivity from the TEM measurements and water content and relaxation time from the SNMR measurements were used in a K-means clustering scheme to resolve subsurface structures. The K-means clustering was evaluated with a silhouette index to pick the number of clusters. After clustering, each cluster was assigned a hydrogeological description based on the distinct features in the three parameters, e.g. a low resistivity, high water content, and high T2* is assigned as saltwater saturated sand. In the first case study, the clusters enabled improved resolution of a regional water table in an unconfined aquifer setting by the multi-geophysical approach. The water table estimates were positively evaluated against multiple boreholes within 500 m of coincident geophysical models. The second case study illustrates how clustering, of SNMR and TEM models, can delineate saltwater intrusion in an island coastal aquifer, which would not be possible with any of these methods individually. Additionally, the clustering resolved the main shallow aquifer on the island. Our work illustrates how the combination of geophysical data can be used to improve resolution of hydrogeological layers and reduce interpretational bias.

  • Open Access

    Alleviating interpretational ambiguity in Hydrogeology through clustering-based analysis of transient electromagnetic and surface nuclear magnetic resonance data

    by Mathias Vang, Jakob Juul Larsen, Anders Vest Christiansen, Denys Grombacher

    Local characterization of groundwater systems is critical for managing and protecting vulnerable resources. Geophysical methods can provide dense imaging of subsurface parameters to delineate lithological boundaries and water tables for hydrogeological investigation. Though, using a single geophysical method for determining lithologies can yield erroneous interpretations as different lithologies can have similar properties. By using several geophysical methods, it is possible to reduce this risk and better assign likely lithologies to subsurface units. We present two case studies where transient electromagnetic (TEM) and surface nuclear magnetic resonance (SNMR) are used in combination to delineate hydrogeological structures. Novel spatially constrained inversion in SNMR was used to provide horizontal consistency between soundings. Three coincident parameters, resistivity from the TEM measurements and water content and relaxation time from the SNMR measurements were used in a K-means clustering scheme to resolve subsurface structures. The K-means clustering was evaluated with a silhouette index to pick the number of clusters. After clustering, each cluster was assigned a hydrogeological description based on the distinct features in the three parameters, e.g. a low resistivity, high water content, and high T2* is assigned as saltwater saturated sand. In the first case study, the clusters enabled improved resolution of a regional water table in an unconfined aquifer setting by the multi-geophysical approach. The water table estimates were positively evaluated against multiple boreholes within 500 m of coincident geophysical models. The second case study illustrates how clustering, of SNMR and TEM models, can delineate saltwater intrusion in an island coastal aquifer, which would not be possible with any of these methods individually. Additionally, the clustering resolved the main shallow aquifer on the island. Our work illustrates how the combination of geophysical data can be used to improve resolution of hydrogeological layers and reduce interpretational bias.

  • Efficient mapping of complex groundwater systems associated with braided rivers using small coil surface nuclear magnetic resonance

    by Mathias Østbjerg Vang, Denys Grombacher, Jakob Juul Larsen, Scott Wilson

    Braided river systems are a substantial source of groundwater recharge in New Zealand. These rivers flow from high relief toward the sea across alluvial plain aquifers, across which the primary groundwater recharge occurs. These aquifers are often used for agricultural irrigation, and overexploitation can occur if there is limited knowledge of aquifer recharge mechanisms. To understand these complex recharge patterns, more detailed knowledge of the lithologic controls on the surface water-groundwater exchange is necessary. Here, we develop a case study in which surface nuclear magnetic resonance (SNMR) is used in braided river systems to identify subsurface structures. We find the method to be efficient in identifying permeability contrasts beneath riverbeds and river berms in multiple river settings. We calibrate a local archetype by coincident borehole lithology and SNMR-derived water contents to find the SNMR signature related to lithologic changes. The resulting archetypes are extrapolated to SNMR sites where there is no coinciding borehole information to identify these lithologic transitions at multiple sites. We find that a combined borehole and SNMR survey can map the transitions from aquifers to low-permeability layers efficiently in three case studies. The small 20 m × 20 m SNMR coil enables acquisition on small bars within the river while resolving the thin-saturated units, previously not resolvable with a larger coil size. The laterally constrained inversion improves lateral consistency and the ability to track the features of the braidplain aquifer in all three rivers within the top 10 m. These results demonstrate SNMR as a multisite geophysical method capable of mapping important hydrogeologic layers to provide valuable information on recharge to vulnerable aquifers.


  • Observation of spikelets in steady-state surface nuclear magnetic resonance data

    by Denys Grombacher, Matthew Peter Griffiths, Mathias Østbjerg Vang, Mason Andrew Kass, Jakob Juul Larsen

    Spikelets in nuclear magnetic resonance (NMR) data occur at predictable frequencies dependent on the repetition time of the excitation sequence. Although spikelets are well documented in other NMR fields, we report their presence in steady-state surface NMR data for the first time. These observations are accompanied by analytical developments to understand and predict their behavior, which follow directly from existing steady-state surface NMR modeling. We show that spikelets represent copies of the surface NMR signal occurring at multiple locations in the frequency domain, including locations that are distinct from the Larmor frequency. These features are shown to be detectable without requiring additional effort in the field and are shown to be readily processed and modeled with only minor modifications to the processing and modeling workflows. Finally, field spikelet data are also inverted to demonstrate that these data can be fit using subsurface models consistent with a reference surface NMR inversion.

  • Open Access

    Technical note: High-density mapping of regional groundwater tables with steady-state surface nuclear magnetic resonance – three Danish case studies

    by Mathias Vang, Denys Grombacher, Matthew P. Griffiths, Lichao Liu, Jakob Juul Larsen

    Groundwater is an essential part of the water supply worldwide, and the demands on this water source can be expected to increase in the future. To satisfy the need for resources and to ensure sustainable use of resources, increasingly detailed knowledge of groundwater systems is necessary. However, it is difficult to directly map groundwater with well-established geophysical methods as these are sensitive to both lithology and pore fluid. Surface nuclear magnetic resonance (SNMR) is the only method with a direct sensitivity to water, and it is capable of non-invasively quantifying water content and porosity in the subsurface. Despite these attractive features, SNMR has not been widely adopted in hydrological research, the main reason being an often-poor signal-to-noise ratio, which leads to long acquisition times and high uncertainty in terms of results. Recent advances in SNMR acquisition protocols based on a novel steady-state approach have demonstrated the capability of acquiring high-quality data much faster than previously possible. In turn, this has enabled high-density groundwater mapping with SNMR. We demonstrate the applicability of the new steady-state scheme in three field campaigns in Denmark, where more than 100 SNMR soundings were conducted with a depth of investigation of approximately 30 m. We show how the SNMR soundings enable us to track water level variations at the regional scale, and we demonstrate a high correlation between water levels obtained from SNMR data and water levels measured in boreholes. We also interpret the SNMR results jointly with independent transient electromagnetic (TEM) data, which allows us to identify regions with water bound in small pores. Field practice and SNMR acquisition protocols were optimized during the campaigns, and we now routinely measure high-quality data at 8 to 10 sites per day with a two-person field crew. Together, the results from the three surveys demonstrate that, with steady-state SNMR, it is now possible to map regional variations in water levels with high-quality data and short acquisition times.


  • Signal Processing Steady-State Surface NMR Data

    by Lichao Liu, Denys Grombacher, Matthew Griffiths, Mathias Vang, Jakob Juul Larsen

    Surface nuclear magnetic resonance (NMR) is a unique technique to study groundwater as it provides direct insights into water content and pore-scale properties. However, surface NMR suffers from an extremely weak signal that limits mapping speeds and can prohibit measurements in high ambient noise environments. It has recently been demonstrated that steady-state sequences can deliver orders of magnitude signal-to-noise ratio enhancement in comparison to standard methods. Most notably, the steady-state approach collapses the surface NMR signal an extremely narrow frequency band, which leads to vastly improved noise rejection. In this paper, we develop the signal processing chain for steady-state surface NMR data. Each step in the signal processing chain, transient culling, pulse windowing, de-spiking, powerline harmonics subtraction and spectral analysis are explained in detail. We demonstrate how error estimation can be efficiently performed using the power spectral density in the vicinity of the transmitting frequency. We also demonstrate how off-resonance excitation can be determined by locating the peak spectrum of surface NMR signal with an array of phase-corrected discrete Fourier transforms. The presented signal processing methods can be easily implemented and applied to extract signal features for quality control and inversion procedures. We give a field example where data collected with steady-state pulse sequences are processed and inverted.


  • Forward Modeling Steady-State Free Precession in Surface NMR

    by Matthew P. Griffiths, Denys Grombacher, Lichao Liu, Mathias O. Vang, Jakob Juul Larsen

    In efforts to map water at depth, steady-state free-precession (SSFP) sequences promise to rapidly increase data acquisition rates in the practice of surface nuclear magnetic resonance (NMR). Unlike conventional surface NMR excitation schemes, pulses in SSFP are transmitted so frequently that the nuclear magnetization of hydrogen in water can not return to its natural alignment with the earth’s ambient magnetic field, and instead achieve a steady-state; a dynamic equilibrium between pulses. Unfortunately, the traditional formulations of SSFP sequences and the full surface NMR forward models are not immediately compatible with each other. Firstly, the traditional analysis of SSFP sequences assume that relaxation during pulse (RDP) effects are negligible, which is not always valid in surface NMR. Secondly, even for single pulse measurements, the surface NMR forward model can be computationally demanding; this challenge scales with the number of pulses. Here we investigate the incorporation of RDP effects on the dynamic equilibrium of SSFP measurements. This is then incorporated into the full surface NMR forward model by deriving analytical expressions to directly predict processed surface NMR data. The model is validated by jointly inverting an extensive and diverse suite of SSFP measurements; 12 distinct sequences each with 16 pulse moments. The inverted model has a data misfit of 0.99 and is consistent with models derived from standard NMR data. The ability of our forward model to reproduce diverse signals and jointly invert them is a strong indication of its validity.