HWHaibo Wu

Haibo Wu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Haibo Wu has a total of 25 co-authors. Here are the top co-authors by number of shared publications:

  • Bingbing Pei

    State Key Laboratory of Advanced Marine Materials, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201, China

    5 shared publications
  • Xishi Wu

    State Key Laboratory of Advanced Marine Materials, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201, China

    5 shared publications
  • Zehua Liu

    State Key Laboratory of Advanced Marine Materials, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201, China

    5 shared publications
  • Huan Liu

    Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201, China

    4 shared publications
  • Jianshen Han

    Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201, China

    4 shared publications
  • Yitian Yang

    Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201, China

    4 shared publications

Latest Publications

  • Open Access

    Irradiation Damage Behavior and Mechanism of Pressureless-Sintered ZrC Ceramics

    by Junping Ma, Haibo Wu, Huan Liu, Yitian Yang, Zehua Liu, Xishi Wu, Bingbing Pei, Jianshen Han, Canglong Wang, Zhengren Huang

    Zirconium carbide (ZrC) is a leading candidate for advanced nuclear reactor components due to its ultra-high melting point, thermomechanical stability, and low neutron absorption. However, its irradiation damage behavior and mechanism remains underexplored. In this work, dense pressureless-sintered ZrC ceramics with low-neutron-absorption MoSi2 additives were irradiated with 500 keV He2+ ions at room temperature to peak damage levels of 0.30, 1.49, and 2.97 dpa. The changes in their microstructure, bonding states, and property were analyzed via TEM, GIXRD, Raman spectroscopy, nanoindentation, and TDTR. ZrC retained crystallinity regardless of high-density black-spot defects, while MoSi2 exhibited severe amorphization and swelling. Lattice expansion and partial Zr-C bond breakage with C-C bond formation were confirmed, with maximum hardening at 1.49 dpa and significant elastic modulus reduction at 2.97 dpa. Thermal conductivity decreased modestly and showed minimal dose dependence, indicating a saturation effect. These results elucidate defect evolution in pressureless-sintered ZrC-MoSi2 ceramics and support its application in high-irradiation nuclear environments.

  • Open Access

    Hydrophilic Treatment Methods for Porous Transport Layers on Bubble Management and Electrolysis Performance in Proton Exchange Membrane Water Electrolyzer

    by Xuezhi Bao, Bo Huang, Ziqing Wang, Luhaibo Zhao, Haibo Wu, Shen Xu, Guoliang Wang, Zhiyong Tang

    The hydrophilicity of the porous transport layer (PTL) critically influences the mass transport overpotential and overall efficiency of a proton exchange membrane water electrolyzer (PEMWE). In this study, titanium felts with three distinct levels of hydrophilicity are systematically characterized and evaluated electrochemically. A novel bilayer gradient hydrophilic titanium felt structure is designed, resulting in notable performance improvements: the average cell voltage decreases by 12.92%, and the overpotential is reduced by 9.94–18.03% across a current density range of 0.1–1.6 A·cm−2. High-speed imaging reveals that the gradient hydrophilic structure effectively regulates bubble dynamics, nearly eliminating annular flow bubbles, reducing the proportion of slug flow bubbles by 40.78%, decreasing the bubble detachment diameter by 28.26%, and enhancing bubble displacement by 51.03% compared to that of untreated titanium felt. These results demonstrate that gradient hydrophilic structures can significantly enhance PEMWE performance, offering a promising strategy and a theoretical foundation for optimizing mass transfer in electrolytic systems.


  • Open Access

    Multiphysics Modelling Flow Disturbance Optimization of Proton Exchange Membrane Water Electrolysis Under Bubble Effects

    by Chengming Du, Bo Huang, Ziqing Wang, Luhaibo Zhao, Haibo Wu, Shen Xu, Guoliang Wang, Zhiyong Tang

    In Proton Exchange Membrane Water Electrolysis (PEMWE), the two-phase flow distribution in the anode field significantly affects overall electrolysis performance. Based on visualized experimental data, in this paper, the reaction kinetics equations were theoretically revised, and a three-dimensional, two-phase, non-isothermal, multi-physics coupled model of the electrolysis was developed and experimentally validated. Four different configurations of rectangular turbulence promoters were designed within the anode serpentine flow field and compared with a conventional serpentine flow field (SFF) in terms of their multi-physics distribution characteristics. The results showed that, in the double-row rectangular block serpentine flow field (DRB SFF), the uniformity of liquid water saturation, temperature, and current density improved by 16.6%, 0.49% and 40.8%, respectively. The normal mass transfer coefficient increased by a factor of 6.3, and polarization performance improved by 6.98%. A cross-arranged turbulence promoter structure was further proposed. This design maintains effective turbulence while reducing flow resistance and pressure drop, thereby enhancing mass transfer efficiency and overall electrolysis performance through improved bubble fragmentation.


  • Open Access

    Effects of SiC Particle Size on SiCp/Al Composite During Vacuum Hot Pressing

    by Ruijie Feng, Haibo Wu, Huan Liu, Yitian Yang, Bingbing Pei, Jianshen Han, Zehua Liu, Xishi Wu, Zhengren Huang

    High-performance SiCp/Al composites were fabricated via a vacuum hot-pressing powder metallurgy process. The effects of SiC particle size on the composite microstructures and their thermal and mechanical properties were systematically investigated. The vacuum hot-pressed SiCp/Al composites exhibited a well-bonded interface between the SiC particles and Al matrix, while not exhibiting any Al4C3 brittle phase. Particle gradation effectively enhanced the densification of SiCp/Al composites, resulting in dense bulks with a relative density of 99.7%. When the SiC particle size increased from 5 to 50 μm, the fracture morphologies gradually transitioned from intergranular to transgranular, while the relative density, bending strength, and thermal conductivity increased. Overall, SiCp/Al composites with excellent thermal conductivity (201.42 W/(m·K)) and bending strength (523 ± 29.45 MPa) were obtained. To address the scarcity of research on SiCp/Al composites’ thermal properties, this study establishes SiC size/gradation–property relationships, innovatively filling the gap in thermal performance regulation.


  • Open Access

    The Modulation of the Pore Structure in Porous Carbon by Metal Salts and Its Application for Joining Silicon Carbide Ceramics

    by Xishi Wu, Zehua Liu, Bingbing Pei, Haibo Wu, Zhengren Huang

    In this work, the metal salts were introduced into the resin-solvent gel system to leverage their ortho-substitution effect, thereby accelerating the polymerization-induced phase separation process. Subsequent in-situ carbonization resulted in the preparation of porous carbon materials with three-dimensional interconnected pores. By precisely tuning the parameters of the resin-solvent-metal ion system, control over the pore structure of the porous carbon was achieved, with a porosity range of 16.5% to 66.5% and a pore diameter range of 8 to 248 nm. The addition of metallic salts can simply and effectively increase the pore structure after carbonization, making the infiltration of molten silicon easier. This is beneficial to the joining process of silicon carbide ceramics. Based on these findings, a high-reliability joining technique for large-sized (135 mm × 205 mm) silicon carbide ceramics was developed. The resulting interlayer was dense and defect-free, exhibiting a joining strength of 309 ± 33 MPa and a Weibull modulus of 10.67. These results highlight the critical role of structured porous media in advancing the field of large-sized ceramic joining.


  • Open Access

    Microstructure and Properties of Pressureless-Sintered Zirconium Carbide Ceramics with MoSi2 Addition

    by Xiuzheng Chen, Haibo Wu, Huan Liu, Yitian Yang, Bingbing Pei, Jianshen Han, Zehua Liu, Xishi Wu, Zhengren Huang

    Zirconium carbide (ZrC) ceramics have a high melting point, low neutron absorption cross section, and excellent resistance to the impact of fission products and are considered to be one of the best candidate materials for fourth-generation nuclear energy systems. ZrC ceramics with a high relative density of 99.1% were successfully prepared via pressureless sintering using a small amount of MoSi2 as an additive. The influence of the MoSi2 content on the densification behavior, microstructure, mechanical properties, and thermal properties of ZrC ceramics was systematically investigated. The results show that the densification of ZrC was significantly enhanced by the introduction of MoSi2 due to the formation of a liquid phase during sintering. In addition, the ZrC grains were refined due to the pinning effect of the generated silicon carbide. The flexural strength and Vickers hardness of ZrC ceramics with 2.5 vol% MoSi2 sintered at 1850 °C were 408 ± 12 MPa and 17.1 GPa, respectively, which were approximately 30% and 10% higher compared to the samples without the addition of MoSi2. The improved mechanical properties were mainly attributed to the high relative density (99.1%) and refined microstructure.


  • Open Access

    Effect of Ti Doping on the Microstructure and Properties of SiCp/Al Composites by Pressureless Infiltration

    by Ruijie Feng, Haibo Wu, Huan Liu, Yitian Yang, Bingbing Pei, Jianshen Han, Zehua Liu, Xishi Wu, Zhengren Huang

    The effects of Ti doping on the microstructure and properties of SiCp/Al composites fabricated by pressureless infiltration were comprehensively investigated using first-principles calculations and experimental analyses. First-principles calculations revealed that the interface wetting and bonding strength in an Al/SiC system could be significantly enhanced by Ti doping. Subsequently, the Ti element was incorporated into SiC preforms in the form of TiO2 and TiC to verify the influence of Ti doping on the pressureless infiltration performance of SiCp/Al composites. The experimental results demonstrated that the pressureless infiltration of molten Al into SiC preforms was promoted by adding TiC or TiO2 due to the improved wettability. However, incorporating TiO2 leads to the growth of AlN whiskers under a N2 atmosphere, thereby hindering the complete densification of the composites. On the other hand, TiC doping can improve wettability and interface strength without deleterious reactions. As a consequence, the TiC-doped SiCp/Al composites exhibited excellent properties, including a high relative density of 99.4%, a bending strength of 287 ± 18 MPa, and a thermal conductivity of 142 W·m−1·K−1.


  • Open Access

    Microstructures and Properties of Porous Liquid-Phase-Sintered SiC Ceramic by Hot Press Sintering

    by Yajie Li, Haibo Wu, Xuejian Liu, Zhengren Huang

    Porous liquid-phase-sintered SiC (L-SiC) ceramics were successfully fabricated by hot press sintering (HP) at 1800 °C in argon, using Al2O3 and Y2O3 as oxide additions. By varying the starting coarse SiC particle size, the relationships between pore microstructures and flexural strength as well as gas permeability of porous L-SiC were examined. All the as-sintered samples possessed homogeneous interconnected pores. The porosity of porous L-SiC decreased from 34.0% to 25.9%, and the peak pore size increased from 1.1 to 3.8 μm as the coarse SiC particle sizes increased. The flexural strengths of porous L-SiC ceramics at room temperature and 1000 °C were as high as 104.3 ± 7.3 MPa and 78.8 ± 5.1 MPa, respectively, though there was a decrease in accordance with their increasing pore sizes and particle sizes. Moreover, their gas permeability increased from 1.4 × 10−14 m2 to 4.6 × 10−14 m2 with the increase of pore size in spite of their decreased porosity.


  • Grain Composition on Solid-state-sintered SiC Ceramics

    by Xing Yuan-Yuan, Wu Hai-Bo, Liu Xue-Jian, Huang Zheng-Ren