Giuseppe Di Vito Nolfi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Giuseppe Di Vito Nolfi has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Leucio Rossi
Department of Physical and Chemical Sciences, University of L’Aquila, Via Vetoio, Coppito, 67100 L’Aquila, Italy
5 shared publications - Katia Gallucci
Department of Industrial and Information Engineering and Economics, University of L’Aquila, 67100 L’Aquila, Italy
4 shared publications - Fabrizio Ruggieri
Department of Physical and Chemical Sciences (DSFC), University of L’Aquila, Via Vetoio (“A.C. De Meis” Building), 67100 L’Aquila, Italy
2 shared publications - Alessia Smarrella
Department of Physical and Chemical Sciences (DSFC), University of L’Aquila, Via Vetoio (“A.C. De Meis” Building), 67100 L’Aquila, Italy
1 shared publication - Andrea Di Giuliano
Department of Industrial and Information Engineering and Economics (DIIIE), University of L’Aquila, Piazzale E. Pontieri 1, 67100 L’Aquila, Italy
1 shared publication - Annalisa Troiani
Department of Physical and Chemical Sciences (DSFC), University of L’Aquila, Via Vetoio (“A.C. De Meis” Building), 67100 L’Aquila, Italy
1 shared publication
Latest Publications
- Open Access
- 12 November 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (22) , 11193
Comparison of Conventional Hydrothermal and Microwave-Assisted Zeolitization of Coal Fly Ash Cenospheres and DoE-Based Evaluation of Cd(II) Removal Conditions
Coal fly ash-derived cenospheres represent a secondary aluminosilicate resource that can be converted into zeolitic materials for metal removal from water. In this study, acid-pretreated and NaOH-activated cenospheres were crystallized by conventional hydrothermal treatment (ZH) or microwave-assisted treatment (ZM), and the resulting materials were evaluated for Cd(II) removal. XRD, SEM, ATR-FTIR and N2 physisorption were used for physicochemical characterization, while adsorption performance was investigated through material screening, pH-dependent experiments and a three-factor, three-level full factorial design considering initial Cd(II) concentration, pH and temperature. Microwave treatment reduced the crystallization step from three days to 4 h and produced ZM with a higher BET surface area (362.5 vs. 252.2 m2 g−1) and total pore volume (0.227 vs. 0.152 cm3 g−1) than ZH. ZM also showed higher Cd(II) removal, particularly at 50 mg L−1, where removal reached 88.6% compared with 44.1% for ZH. Cd(II) removal showed only limited changes between 1 and 3 h and remained high over pH 4–8. Response surface analysis showed nonlinear effects of Cd(II) concentration and temperature and a significant concentration–temperature interaction. The microwave-assisted route thus provided a shorter crystallization step and yielded a material with higher BET surface area, total pore volume and Cd(II) removal performance under the investigated conditions.
- 12 November 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (22) , 11193
Open AccessComparison of Conventional Hydrothermal and Microwave-Assisted Zeolitization of Coal Fly Ash Cenospheres and DoE-Based Evaluation of Cd(II) Removal Conditions
Coal fly ash-derived cenospheres represent a secondary aluminosilicate resource that can be converted into zeolitic materials for metal removal from water. In this study, acid-pretreated and NaOH-activated cenospheres were crystallized by conventional hydrothermal treatment (ZH) or microwave-assisted treatment (ZM), and the resulting materials were evaluated for Cd(II) removal. XRD, SEM, ATR-FTIR and N2 physisorption were used for physicochemical characterization, while adsorption performance was investigated through material screening, pH-dependent experiments and a three-factor, three-level full factorial design considering initial Cd(II) concentration, pH and temperature. Microwave treatment reduced the crystallization step from three days to 4 h and produced ZM with a higher BET surface area (362.5 vs. 252.2 m2 g−1) and total pore volume (0.227 vs. 0.152 cm3 g−1) than ZH. ZM also showed higher Cd(II) removal, particularly at 50 mg L−1, where removal reached 88.6% compared with 44.1% for ZH. Cd(II) removal showed only limited changes between 1 and 3 h and remained high over pH 4–8. Response surface analysis showed nonlinear effects of Cd(II) concentration and temperature and a significant concentration–temperature interaction. The microwave-assisted route thus provided a shorter crystallization step and yielded a material with higher BET surface area, total pore volume and Cd(II) removal performance under the investigated conditions.
- Open Access
- 6 October 2026
- Published by Elsevier in SSRN Electronic Journal
Optimization of pharmaceutical emerging pollutants removal from water using surface-tuned magnetoliposomes: influence of lipid structure and process optimization
The efficient removal of pharmaceutical contaminants from water remains a critical challenge due to their persistence and complex interactions with conventional treatment systems. Our investigation is focused on magnetoliposomes (MLs), nanostructured interfaces for water remediation due to apolar contaminant–interface interactions. MLs are composed of magnetite nanoparticles functionalized with tunable lipid bilayers: the aim of this study is providing a model platform to investigate how interfacial composition and physicochemical properties govern pollutant capture in the organic portion. Surface charge and lipid composition (saturation, packing, and fluidity) were systematically varied and tested for the removal of representative pharmaceuticals with different hydrophobicity and ionization behavior. Removal efficiency resulted significantly affected by interfacial processes governed by hydrophobic partitioning, electrostatic interactions, and bilayer permeability acting synergistically and bilayer organization. These findings establish MLs as a versatile platform for interface-driven environmental remediation and provide fundamental insights into how interfacial engineering can be leveraged to control contaminant capture in complex aqueous systems.
- 6 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessOptimization of pharmaceutical emerging pollutants removal from water using surface-tuned magnetoliposomes: influence of lipid structure and process optimization
The efficient removal of pharmaceutical contaminants from water remains a critical challenge due to their persistence and complex interactions with conventional treatment systems. Our investigation is focused on magnetoliposomes (MLs), nanostructured interfaces for water remediation due to apolar contaminant–interface interactions. MLs are composed of magnetite nanoparticles functionalized with tunable lipid bilayers: the aim of this study is providing a model platform to investigate how interfacial composition and physicochemical properties govern pollutant capture in the organic portion. Surface charge and lipid composition (saturation, packing, and fluidity) were systematically varied and tested for the removal of representative pharmaceuticals with different hydrophobicity and ionization behavior. Removal efficiency resulted significantly affected by interfacial processes governed by hydrophobic partitioning, electrostatic interactions, and bilayer permeability acting synergistically and bilayer organization. These findings establish MLs as a versatile platform for interface-driven environmental remediation and provide fundamental insights into how interfacial engineering can be leveraged to control contaminant capture in complex aqueous systems.
- Open Access
- 2 October 2026
- Published by MDPI AG in Clean Technologies
- Vol. 8 (5) , 159
Reutilization of Ashes from the Solid Fraction of Digestate as Sorbent Materials in Pressure Swing Adsorption for Biogas Upgrading to Biomethane
The quantity of the solid fraction of digestate (SFD) from anaerobic digestion is expected to reach 177 million tons of dry material in the EU by 2050, and therefore requires sustainable management aligned with circular economy principles. Thermochemical valorization is a possible solution, even though it produces ashes as a by-product. This work experimentally investigates the reuse of SFD ashes to obtain recovered sorbents for CO2 capture in biogas upgrading via pressure swing adsorption (PSA). Five ash-based sorbent materials were synthesized: (i) SFD ash calcinated at 700 °C (ASFD700); (ii) SFD ash calcinated at 900 °C (ASFD900); (iii) ASFD700 washed with an HCl solution (AWSFD700); (iv) ASFD900 washed with an HCl solution (AWSFD900); (v) AWSFD900 modified by zeolitization (ZSFD900). These materials were tested for CO2/CH4 separation by PSA. XRF, XRD, BET-BJH, PSD, SEM-EDS, and FT-IR were used to characterize the solid samples. PSA experiments were performed at industrially relevant pressures (5–9 bara) and room temperature. AWSFD700, AWSFD900, and ZSFD900 had the highest CO2 sorption capacities, reaching up to 1.06 ± 0.25 mmolCO2 g−1 at 9 bara for AWSFD900, while comparable performances were observed for AWSFD700 and ZSFD900; CO2/CH4 selectivity decreased with increasing pressure from approximately 1.4–1.8 mmolCO2 mmolCH4−1 at 5 bara to approximately 0.9–1.0 mmolCO2 mmolCH4−1 at 9 bara, due to competitive adsorption effects. The obtained zeolitic phase in ZSFD900 was analcime, which has a narrow pore size, a key limitation for its application in PSA. Overall, SFD-derived ashes showed potential to form alternative sorbents for biogas upgrading.
- 2 October 2026
- Published by MDPI AG in Clean Technologies
- Vol. 8 (5) , 159
Open AccessReutilization of Ashes from the Solid Fraction of Digestate as Sorbent Materials in Pressure Swing Adsorption for Biogas Upgrading to Biomethane
The quantity of the solid fraction of digestate (SFD) from anaerobic digestion is expected to reach 177 million tons of dry material in the EU by 2050, and therefore requires sustainable management aligned with circular economy principles. Thermochemical valorization is a possible solution, even though it produces ashes as a by-product. This work experimentally investigates the reuse of SFD ashes to obtain recovered sorbents for CO2 capture in biogas upgrading via pressure swing adsorption (PSA). Five ash-based sorbent materials were synthesized: (i) SFD ash calcinated at 700 °C (ASFD700); (ii) SFD ash calcinated at 900 °C (ASFD900); (iii) ASFD700 washed with an HCl solution (AWSFD700); (iv) ASFD900 washed with an HCl solution (AWSFD900); (v) AWSFD900 modified by zeolitization (ZSFD900). These materials were tested for CO2/CH4 separation by PSA. XRF, XRD, BET-BJH, PSD, SEM-EDS, and FT-IR were used to characterize the solid samples. PSA experiments were performed at industrially relevant pressures (5–9 bara) and room temperature. AWSFD700, AWSFD900, and ZSFD900 had the highest CO2 sorption capacities, reaching up to 1.06 ± 0.25 mmolCO2 g−1 at 9 bara for AWSFD900, while comparable performances were observed for AWSFD700 and ZSFD900; CO2/CH4 selectivity decreased with increasing pressure from approximately 1.4–1.8 mmolCO2 mmolCH4−1 at 5 bara to approximately 0.9–1.0 mmolCO2 mmolCH4−1 at 9 bara, due to competitive adsorption effects. The obtained zeolitic phase in ZSFD900 was analcime, which has a narrow pore size, a key limitation for its application in PSA. Overall, SFD-derived ashes showed potential to form alternative sorbents for biogas upgrading.
- Open Access
Valorization of Coal Fly Ash Cenospheres as Catalyst Supports for Green Diesel Synthesis
To reduce dependence on fossil fuels and limit their environmental impact, the development of biofuels represents an effective strategy. Green diesel is a biofuel synthesized from vegetable oil that is fully compatible with conventional diesel engines and therefore represents a promising alternative to mineral diesel. In addition, the use of waste-derived catalysts can further improve the sustainability of the process. In this study, fly ash cenospheres (FAC), an abundant industrial waste, were used as a support to synthesize several transition-metal-based catalysts. The catalysts were tested for the catalytic deoxygenation of vegetable oils in a batch reactor at 320 °C and 40 bar H2 using 10 wt% catalyst and n-hexane as the solvent. Among the tested catalysts, NiMo(5/15)/FAC exhibited the best performance, achieving complete conversion and producing a biofuel containing 91.7% C15–C18 hydrocarbons. The physicochemical properties of the catalyst were investigated using ICP-MS, FT-IR, XRD, and BET-BJH analyses. The effects of the solvent, feedstock, and catalyst reuse were also evaluated. In the recycling tests, the catalyst activity rapidly decreased; however, the regeneration step fully restored its catalytic performance. These results show that FAC can be effectively valorized as a catalyst support for green diesel synthesis.
Open AccessValorization of Coal Fly Ash Cenospheres as Catalyst Supports for Green Diesel Synthesis
To reduce dependence on fossil fuels and limit their environmental impact, the development of biofuels represents an effective strategy. Green diesel is a biofuel synthesized from vegetable oil that is fully compatible with conventional diesel engines and therefore represents a promising alternative to mineral diesel. In addition, the use of waste-derived catalysts can further improve the sustainability of the process. In this study, fly ash cenospheres (FAC), an abundant industrial waste, were used as a support to synthesize several transition-metal-based catalysts. The catalysts were tested for the catalytic deoxygenation of vegetable oils in a batch reactor at 320 °C and 40 bar H2 using 10 wt% catalyst and n-hexane as the solvent. Among the tested catalysts, NiMo(5/15)/FAC exhibited the best performance, achieving complete conversion and producing a biofuel containing 91.7% C15–C18 hydrocarbons. The physicochemical properties of the catalyst were investigated using ICP-MS, FT-IR, XRD, and BET-BJH analyses. The effects of the solvent, feedstock, and catalyst reuse were also evaluated. In the recycling tests, the catalyst activity rapidly decreased; however, the regeneration step fully restored its catalytic performance. These results show that FAC can be effectively valorized as a catalyst support for green diesel synthesis.
- Open Access
Production of Green Diesel via the Ni/Al Mo Hydrotalcite Catalyzed Deoxygenation of Rapeseed Oil
Growing concern about anthropogenic climate change and the continuous increase in the energy demand have driven the need to explore new energy sources, particularly in the transportation sector. Biodiesel is one of the most widely used biofuels, but its disadvantages restrict its use in blends with conventional diesel. A better alternative is green diesel, a hydrocarbon biofuel that can be used in its pure form and is produced through the catalytic deoxygenation of vegetable oils. In this study, a NiMoAl catalyst derived from layered double hydroxides (LDHs) was synthesized and used for the catalytic deoxygenation of rapeseed oil to produce green diesel. The catalyst was characterized using IR, XRD, and BET analysis. The reactions were carried out in a batch reactor, and parameters such as the temperature, pressure, catalyst loading, and reaction time were examined. The results demonstrated that the complete conversion of rapeseed oil was achieved under optimal conditions (320 °C, 40 bar H2, 4 wt% catalyst), with a diesel-range hydrocarbon content of over 90%. The recyclability of the catalyst was also evaluated, showing sustained activity over multiple reaction cycles while maintaining high conversion and selectivity toward hydrocarbons in the diesel range.
Open AccessProduction of Green Diesel via the Ni/Al Mo Hydrotalcite Catalyzed Deoxygenation of Rapeseed Oil
Growing concern about anthropogenic climate change and the continuous increase in the energy demand have driven the need to explore new energy sources, particularly in the transportation sector. Biodiesel is one of the most widely used biofuels, but its disadvantages restrict its use in blends with conventional diesel. A better alternative is green diesel, a hydrocarbon biofuel that can be used in its pure form and is produced through the catalytic deoxygenation of vegetable oils. In this study, a NiMoAl catalyst derived from layered double hydroxides (LDHs) was synthesized and used for the catalytic deoxygenation of rapeseed oil to produce green diesel. The catalyst was characterized using IR, XRD, and BET analysis. The reactions were carried out in a batch reactor, and parameters such as the temperature, pressure, catalyst loading, and reaction time were examined. The results demonstrated that the complete conversion of rapeseed oil was achieved under optimal conditions (320 °C, 40 bar H2, 4 wt% catalyst), with a diesel-range hydrocarbon content of over 90%. The recyclability of the catalyst was also evaluated, showing sustained activity over multiple reaction cycles while maintaining high conversion and selectivity toward hydrocarbons in the diesel range.
- Open Access
- 10 December 2021
- Published by MDPI AG in International Journal of Environmental Research and Public Health
- Vol. 18 (24) , 13041
Green Diesel Production by Catalytic Hydrodeoxygenation of Vegetables Oils
Non-renewable fossil fuels and the air pollution associated with their combustion have made it necessary to develop fuels that are environmentally friendly and produced from renewable sources. In addition, global warming and climate change have brought to the attention of many countries the need to develop programs and reforms, such as the 2030 Agenda of the United Nations and the European Green Deal, that finance and promote the conversion of all socio-economic activities in favor of sustainable and environmentally friendly development. These major projects include the development of non-polluting biofuels derived from renewable sources. Vegetable oils are a renewable source widely used to produce biofuels due to their high energy density and similar chemical composition to petroleum derivatives, making them the perfect feedstock for biofuel production. Green diesel and other hydrocarbon biofuels, obtained by the catalytic deoxygenation of vegetable oils, represent a sustainable alternative to mineral diesel, as they have physico-chemical properties similar to derived oil fuels. The catalyst, temperature, hydrogen pressure, and the type of vegetable oil can influence the type of biofuel obtained and its properties. The main aspects discussed in this review include the influence of the catalyst and reaction conditions on the catalytic deoxygenation reaction.
- 10 December 2021
- Published by MDPI AG in International Journal of Environmental Research and Public Health
- Vol. 18 (24) , 13041
Open AccessGreen Diesel Production by Catalytic Hydrodeoxygenation of Vegetables Oils
Non-renewable fossil fuels and the air pollution associated with their combustion have made it necessary to develop fuels that are environmentally friendly and produced from renewable sources. In addition, global warming and climate change have brought to the attention of many countries the need to develop programs and reforms, such as the 2030 Agenda of the United Nations and the European Green Deal, that finance and promote the conversion of all socio-economic activities in favor of sustainable and environmentally friendly development. These major projects include the development of non-polluting biofuels derived from renewable sources. Vegetable oils are a renewable source widely used to produce biofuels due to their high energy density and similar chemical composition to petroleum derivatives, making them the perfect feedstock for biofuel production. Green diesel and other hydrocarbon biofuels, obtained by the catalytic deoxygenation of vegetable oils, represent a sustainable alternative to mineral diesel, as they have physico-chemical properties similar to derived oil fuels. The catalyst, temperature, hydrogen pressure, and the type of vegetable oil can influence the type of biofuel obtained and its properties. The main aspects discussed in this review include the influence of the catalyst and reaction conditions on the catalytic deoxygenation reaction.