Rostislav Králík

Rapid solidification by melt-spinning produces aluminum alloys with extremely refined microstructures but also introduces strong structural gradients across the ribbon thickness. In this work, the microstructural evolution of a rapidly solidified Al-Cu-Li-Mg-Sc-Zr alloy was investigated during model homogenization using in situ STEM heating experiments and correlated with bulk electrical-resistivity measurements. The as-cast ribbons exhibit two distinct solidification zones: a near-contact region consisting of columnar cells containing fine Cu-rich spherical precipitates, and a central region composed of larger eutectic cells enriched in Al₂Cu and Al₇Cu₂Fe phases. Stepwise in situ STEM annealing between 200 °C and 500 °C reveals a sequence of transformations, including matrix depletion due to precipitation of strengthening phases, coarsening of primary phases, and formation of Al₃(Sc,Zr) dispersoids. Above 500 °C, rapid dissolution of Cu-rich primary phases occurs, leaving only a limited number of stable grain-boundary particles of the Al₇Cu₂Fe phase, eliminating the original two-zone structure, and resulting in a fully homogenized ribbon. Ex situ annealing confirms that the resulting microstructure is uniform across the ribbon thickness and enables consistent precipitation strengthening during artificial aging. The proposed annealing treatment is based on numerical models for homogenization of eutectic systems. The final annealing step combines homogenization and solution treatment at 530 °C for periods close to 5 min—two orders of magnitude shorter than standard holding times. Microhardness measurements from both ribbon surfaces reveal an identical peak-aged hardness of 135 HV, validating the effectiveness of the short-time homogenization strategy for rapidly solidified Al-Cu-Li-Mg-based alloys.

Rapid solidification by melt‑spinning produces aluminum alloys with extremely refined microstructures but also introduces strong structural gradients across the ribbon thickness. In this work, the microstructural evolution of a rapidly solidified Al‑Cu‑Li‑Mg‑Sc‑Zr alloy was investigated during model homogenization using in‑situ STEM heating experiments and correlated with bulk electrical‑resistivity measurements. The as‑cast ribbons exhibit two distinct solidification zones: a near‑contact region consisting of columnar cells containing fine Cu‑rich spherical precipitates, and a central region composed of larger eutectic cells enriched in Al₂Cu and Al₇Cu₂Fe phases. Stepwise in‑situ annealing between 200 °C and 550 °C reveals a sequence of transformations, including matrix depletion due to precipitation of strengthening phases, coarsening and dissolution of primary phases, and the formation of Al₃(Sc,Zr) dispersoids. Above 500 °C, rapid dissolution of primary phases followed by their coagulation into a limited number of stable grain‑boundary particles eliminates the original two‑zone structure and results in a fully homogenized ribbon. Ex‑situ annealing confirms that the resulting microstructure is uniform across the ribbon thickness and enables consistent precipitation strengthening during artificial aging. Microhardness measurements from both ribbon surfaces reveal identical peak‑aged hardness, validating the effectiveness of the short‑time homogenization strategy for rapidly solidified Al‑Cu‑Li‑Mg-based alloys.

The influence of the casting method on the microstructures of Al-Cu-Li-Mg-Zr-Sc was examined. The techniques include mold casting, twin-roll casting, and melt spinning. Estimated solidification rates of up to 10 7 K•s-1 produce dendritic solidification with eutectic cells ranging from 500 nm to 50 μm, decorated by primary phase particles with thicknesses from 200 nm to 3 μm. Exceeding this solidification rate results in near-diffusionless solidification, which traps more solutes in the matrix. This type of solidification yields a more supersaturated material, with nearly 90% of the total Cu content in the matrix and a fine dispersion of nanoscale spherical precipitates, each with a diameter of less than 100 nm. The small addition of Sc during casting primarily affects the material at low cooling rates, where primary Sccontaining particles modify the grain boundary shape. Al-Cu-Li-Mg-Zr-Sc Mold casting Twin-roll casting Melt-spinning Diffusionless solidification

The sintering dynamics of nickel nanoparticles (Ni NPs) were investigated through a comprehensive approach that included in situ transmission electron microscopy annealing and molecular dynamics simulations. This study systematically examines the transformation behaviors of Ni NP agglomerates over a temperature spectrum from room temperature to 850 °C. Experimental observations, supported by molecular dynamics simulations, revealed the essential influence of rotational and translational motions of particles, especially at lower temperatures, on sintering outcomes. The effect of the orientation of particles on the sintering process was confirmed, with initial configurations markedly determining sintering efficiency and dynamics. Calculated activation energies from this investigation follow those reported in the literature, confirming surface diffusion as the predominant mechanism driving the sintering of Ni NPs.

A homogenization of billets from Al-Cu-Li-Mg-Sc-Zr alloys should be accomplished at high annealing temperatures exceeding 500 °C. This type of aluminum alloy is susceptible to the depletion of surface layers from Li. Therefore, choosing a suitable homogenization temperature and duration is a crucial step in assuring a homogeneous distribution of alloying elements and optimal exploitation of the potential of the alloy. In situ heating in an electron microscope was performed on a twin-roll-cast Al-Cu-Li-Mg-Sc-Zr alloy to understand the peculiarities of the homogenization process. Four types of primary phase particles rich in Cu, Li, Mg, and Fe were identified in the as-cast material. They appear as coarse particles at the boundaries of eutectic cells. Their partial dissolution occurs at temperatures above 450 °C. They are almost fully dissolved at 550 °C, except for complex phases containing Fe and Cu. Small dimensions of eutectic cells in the range of 10 µm assure a homogeneous distribution of the main alloying elements within the matrix after 20 min of annealing at 530 °C. Direct comparison with the same material prepared by mold casting indicates that such short annealing times result in the dissolution of the main primary phase particles but do not assure a homogeneous distribution of the alloying elements in the whole volume of the specimen.

Thin twin-roll cast strips from a model Al-Cu-Mg-Li-Zr alloy with a small addition of Sc were prepared. A combination of a fast solidification rate and a favorable effect of Sc microalloying impacts the size and distribution of primary phase particles and the dimension of eutectic cells. Small interdendritic spacing in the range of 10-15 um enables substitution of the initial long-term homogenization annealing by a two-step annealing at 300 and 450 °C and a short solution treatment at 530 °C before quenching and the final age-hardening procedure. A dense dispersion of small Al3(Sc,Zr) precipitates intensively inhibiting recrystallization forms during this treatment. Further refining and fragmentation of the structure were performed using constrained groove pressing before the solution treatment. Small pre-straining of quenched specimens and subsequent age-hardening simulating T8 temper were used to promote the formation of a homogeneous distribution of strengthening particles and to suppress preferential heterogeneous precipitation on subgrain and grain boundaries. Microstructural features and microhardness evolution during annealing were critically examined and confronted with microstructural characteristics observed on reference mold cast alloy or alloys without Sc alloying. The proposed treatment represents a model near net shape procedure for manufacturing thicker sheets for the aerospace industry.

A homogenization of billets from Al-Cu-Li-Mg-Sc-Zr alloys should be accomplished at high annealing temperatures exceeding 500 °C. This type of aluminum alloy is susceptible to the depletion of surface layers from Li. Therefore, choosing a suitable homogenization temperature and duration is a crucial step in assuring a homogeneous distribution of alloying elements and optimal exploitation of the potential of the alloy. In-situ heating in an electron microscope was performed on a twin-roll cast Al-Cu-Li-Mg-Sc-Zr alloy to understand the peculiarities of the homogenization process. Four types of primary phase particles rich in Cu, Li, Mg, and Fe were identified in the as-cast material. They appear as coarse particles at the boundaries of eutectic cells. Their partial dissolution occurs at temperatures above 450 °C. They are almost fully dissolved at 550 °C, except for complex phases containing Fe and Cu. Small dimensions of eutectic cells in the range of 10 µm assure a homogeneous distribution of main alloying elements within the matrix after 20 min of annealing. Direct comparison with the same material prepared by mold-casting indicates that such short annealing times result in the dissolution of main primary phase particles but do not assure a homogeneous distribution of alloying elements in the whole volume of the specimen.