Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Emeka Charles Nwanna has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Facile Preparation and Characterization of Silica Nanoparticles from South Africa Fly Ash Using a Sol–Gel Hydrothermal Method

    by Patrick Ehi Imoisili, Emeka Charles Nwanna, Tien-Chien Jen

    Silica nanoparticles (SNPs) consist of several applications which include lightweight aggregates, energy storage, and drug delivery. Nevertheless, the silica reagents used in SNP synthesis are both costly and hazardous. As a result, it is critical to look for other sources of silica. For this research, a simple sol–gel hydrothermal approach is used to make SNPs from South African fly ash (SAFA). SAFA is classified as fly ash class F according to X-ray fluorescence (XRF) analysis. The wide-angle X-ray diffraction (XRD) pattern reveals the structural composition of SAFA and the amorphous phase of extracted SNPs, while Fourier transform infrared (FTIR) examination reveals the presence of silanol and siloxane groups. Basic SNPs were generally spherical with diameters of about 60 nm, according to scanning electron microscopy (SEM) and transition electron microscope (TEM) studies. The presence of SiO2 is confirmed by energy-dispersive X-ray spectroscopy (EDX) spectrum analysis. Particle size assessment indicates particle sizes ranging from 48 nm to 87 nm in diameter, with a mean diameter of 67 nm. The application of SNPs in wastewater treatment demonstrated that they can be used to remove Cd2+ from an aqueous solution. This research offers new ideas for using South African fly ash in SNP manufacturing.


  • A numerical approach on the selection of the purge flow rate in an atomic layer deposition (ALD) process

    by Emeka Charles Nwanna, Rigardt Alfred Maarten Coetzee, Tien-Chien Jen

    The variation of the purge flow rate is investigated in a reactor scale simulation of a typical atomic layer deposition (ALD) process. The investigation in its context addresses the possible issues of inadequate deposition rates with regard to the purge flow rate. A three-dimensional reactor is numerically implemented to simulate the physical and chemical processes to fabricate aluminum oxide (Al2O3) thin films. The purge flow rate disparity is focused to examine the effects within the fluid flow, mass transport, along with the chemical kinetics of the ALD process. The fabrication process employs trimethyl-aluminum and ozone (O3) as the metal and oxidant precursors, respectively, and inert argon as the purge gas. The reactor operation is set up to operate at a pressure of 10 torrs, with a substrate temperature of 200 °C. Three purge flow rates of 20, 10, and 5 sccm, respectively, have been examined. It was discovered that the slower flow rate showed, superior mass fraction distribution, reached unity surface coverage, and a time extensive surface deposition rate. A prolonged ozone exposure was crucial in providing an adequately oxidized substrate. The 20, 10, and 5 sccm purge flow rate growth obtained a 0.58, 0.85, and 1.6 Å/cycle, respectively. These findings revealing close similarities to experimental behaviors and recorded growths.


  • Green synthesis of CuNb 2 O 6 thin film using allium cepa as catalyst

    by Emeka Charles Nwanna, Patrick Ehi Imoisili, Sarah Bitire, Tien-Chien Jen

    The objective of this study was to synthesize and characterize a novel green synthesis of copper niobate (CuNb2O6) thin film using copper (II) sulfate pentahydrate (CuSO4 · 5H2O), an organometallic precursor of bis(cyclopentadienyl) niobium (IV) dichloride (C10H10Cl2Nb), using Allium cepa as a catalyst. The synthesized thin film was characterized using the XRD, EDX, SEM FTIR, UVvis, and 4-point probe measurement. The XRD patterns of the thin film affirmed the formation of a pure monoclinic CuNb2O6 phase. Similarly, the SEM images illustrated the formation of the film and the different film microstructures. The EDX revealed that the thin film consisted of copper (Cu), niobium (Nb), and oxygen (O) elements. The thin film, however, possessed broad absorption in the Ultraviolet-Visible (UV–Vis) region with an absorption edge at 340 nm and an optical bandgap evaluated to be 3.18 eV. Also, the fabricated film’s transmittance ranged between 40% and 55%. A Raman shift of 690 cm−1 was identified at the CuNb2O6 film. The results obtained from the FTIR analysis demonstrated characteristic IR bands at 608 cm−1 and 940 cm−1 which indicated the formation of the Cu-O and Nb-O-Nb bonds. With the rising temperature, an increase in conductivity and a decrease in resistivity were noticed from the plots. This indicated that the synthesized CuNb2O6 thin film exhibited good semiconducting qualities. The prepared CuNb2O6 thin film thus possesses improved electrical properties and can therefore be effectively utilized in photovoltaic solar cells.


  • Open Access

    The impact of CuO nanoparticles as fuel additives in biodiesel-blend fuelled diesel engine: A review

    by Sarah Oluwabunmi Bitire, Emeka Charles Nwanna, Tien-Chien Jen

    The utilization of fossil fuels like diesel has contributed immensely to ecological challenges such as the emission of greenhouse gasses. Hence, the motivation for sourcing another energy that is renewable as well as easily accessible from relatively cheap materials. Biodiesel is a perfect replacement for petro-diesel because it is biodegradable, economically viable, and has lower toxicity. However, there are challenges associated (poor engine efficiency) with its utilization in engines. It also raises NOx emissions which necessitates frequent engine component replacement owing to clogging, and it is ineffective in cold weather. To boost efficiency, nanoparticles can be combined with biodiesel blends. Moreover, the utilization of nanoparticle additives improves the performance of engines, rate of heat transfer, fuel mixture balance, thermo-physical characteristics, as well as the reduction in exhaust emissions. Copper oxide which is a transition metal oxide aids in the heat transfer from the engine down to the exhaust thus lowering the emissions of NOx. As a result, CuO nanoparticles are thought to have a lot of potential as a diesel engine additive and therefore, this review study was conducted to deduce the various techniques for generating CuO nano-fuels, the preparation methods, as well as their physicochemical features. Furthermore, the combustion behaviour, performance, and emission characteristics of diesel engines powered by CuO nanoparticle-containing biodiesel and blends were carefully investigated.


  • Open Access

    An overview of the application of atomic layer deposition process for lithium‐ion based batteries

    by Emeka Charles Nwanna, Sarah Bitire, Patrick Ehi Imoisili, Tien‐Chien Jen


  • Open Access

    Green synthesis preparation and evaluation of CuO doped SnO2

    by Emeka Charles Nwanna, Patrick Ehi Imoisili, Tien-Chien Jen


  • Open Access

    Biosynthesis and Fabrication of Copper Oxide Thin Films as a P-Type Semiconductor for Solar Cell Applications

    by Emeka Charles Nwanna, Patrick Ehi Imoisili, Sarah Oluwabunmi Bitire, Tien-Chien Jen

    This study aimed to synthesize copper oxide (CuO) thin films using an eco-friendly green synthetic approach. A sol-gel spin coating technique was employed for the synthesis of the CuO thin film using Allium cepa as a reducing agent. The fabricated CuO thin film was investigated using the Fourier Transform-Infrared (FTIR) spectroscopy, Ultraviolet-visible spectra studies (UV-Vis), energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM), and the Four-Point Probe measurement. The SEM micrographs revealed that the particles were spherically shaped, while the EDX analysis revealed that the CuO thin film was composed of copper and oxygen elements. Furthermore, the XRD analysis confirmed the monoclinic crystalline structure of the CuO thin film, while the FTIR spectroscopy investigated the chemical bonds formed during the production process. Contrarily, the UV-Vis spectroscopy reported a strong absorption of the film at the visible spectra with an estimated optical energy band gap of 1.48 eV. The electrical analysis, however, disclosed that the synthesized thin film portrayed good semiconducting behaviors.


  • Open Access

    Preparation and Characterization of NbxOy Thin Films: A Review

    by Nwanna Charles Emeka, Patrick Ehi Imoisili, Tien-Chien Jen

    Niobium oxides (NbO, NbO2, Nb2O5), being a versatile material has achieved tremendous popularity to be used in a number of applications because of its outstanding electrical, mechanical, chemical, and magnetic properties. NbxOy films possess a direct band gap within the ranges of 3.2–4.0 eV, with these films having utility in different applications which include; optical systems, stainless steel, ceramics, solar cells, electrochromic devices, capacitor dielectrics, catalysts, sensors, and architectural requirements. With the purpose of fulfilling the requirements of a vast variety of the named applications, thin films having comprehensive properties span described by film composition, morphology, structural properties, and thickness are needed. The theory, alongside the research status of the different fabrication techniques of NbxOy thin films are reported in this work. The impact of fabrication procedures on the thin film characteristics which include; film thickness, surface quality, optical properties, interface properties, film growth, and crystal phase is explored with emphases on the distinct deposition process applied, are also described and discussed.