Leo Lou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Leo Lou has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Boris Rubinsky
University of California Berkeley
4 shared publications - Linnea Warburton
Department of Mechanical Engineering, University of California, Berkeley , Berkeley, CA 94709
2 shared publications - Chenang Lyu
Department of Food Science and Technology, School of Agriculture and Biology, Shanghai Jiao Tong University, Shanghai, China
1 shared publication - Edward Shi
Department of Mechanical Engineering, University of California, Berkeley , Berkeley, CA 94709 ; , Boulder, CO 80309
1 shared publication - Gideon Ukpai
Department of Mechanical Engineering, University of California Berkeley, Berkeley, CA 94720, USA
1 shared publication - Matthew. J. Powell-Palm
Texas A&M University
1 shared publication
Latest Publications
- Open Access
Temperature-Controlled 3D Cryoprinting Inks Made of Mixtures of Alginate and Agar
Temperature-controlled 3D cryoprinting (TCC) is an emerging tissue engineering technology aimed at overcoming limitations of conventional 3D printing for large organs: (a) size constraints due to low print rigidity and (b) the preservation of living cells during printing and subsequent tissue storage. TCC addresses these challenges by freezing each printed voxel with controlled cooling rates during deposition. This generates a rigid structure upon printing and ensures cell cryopreservation as an integral part of the process. Previous studies used alginate-based ink, which has limitations: (a) low diffusivity of the CaCl2 crosslinker during TCC’s crosslinking process and (b) typical loss of print fidelity with alginate ink. This study explores the use of an ink made of agar and alginate to overcome TCC protocol limitations. When an agar/alginate voxel is deposited, agar first gels at above-freezing temperatures, capturing the desired structure without compromising fidelity, while alginate remains uncrosslinked. During subsequent freezing, both frozen agar and alginate maintain the structure. However, agar gel loses its gel form and water-retaining ability. In TCC, alginate crosslinking occurs by immersing the frozen structure in a warm crosslinking bath. This enables CaCl2 diffusion into the crosslinked alginate congruent with the melting process. Melted agar domains, with reduced water-binding ability, enhance crosslinker diffusivity, reducing TCC procedure duration. Additionally, agar overcomes the typical fidelity loss associated with alginate ink printing.
Open AccessTemperature-Controlled 3D Cryoprinting Inks Made of Mixtures of Alginate and Agar
Temperature-controlled 3D cryoprinting (TCC) is an emerging tissue engineering technology aimed at overcoming limitations of conventional 3D printing for large organs: (a) size constraints due to low print rigidity and (b) the preservation of living cells during printing and subsequent tissue storage. TCC addresses these challenges by freezing each printed voxel with controlled cooling rates during deposition. This generates a rigid structure upon printing and ensures cell cryopreservation as an integral part of the process. Previous studies used alginate-based ink, which has limitations: (a) low diffusivity of the CaCl2 crosslinker during TCC’s crosslinking process and (b) typical loss of print fidelity with alginate ink. This study explores the use of an ink made of agar and alginate to overcome TCC protocol limitations. When an agar/alginate voxel is deposited, agar first gels at above-freezing temperatures, capturing the desired structure without compromising fidelity, while alginate remains uncrosslinked. During subsequent freezing, both frozen agar and alginate maintain the structure. However, agar gel loses its gel form and water-retaining ability. In TCC, alginate crosslinking occurs by immersing the frozen structure in a warm crosslinking bath. This enables CaCl2 diffusion into the crosslinked alginate congruent with the melting process. Melted agar domains, with reduced water-binding ability, enhance crosslinker diffusivity, reducing TCC procedure duration. Additionally, agar overcomes the typical fidelity loss associated with alginate ink printing.
- 5 August 2022
- Published by ASME International in Journal of Medical Devices
- Vol. 16 (4)
Three-Dimensional Printing in Combined Cartesian and Curvilinear Coordinates
A three-dimensional (3D) printing technology that facilitates continuous printing along a combination of Cartesian and curvilinear coordinates, designed for in vivo and in situ bioprinting, is introduced. The combined Cartesian/curvilinear printing head motion is accomplished by attaching a biomimetic, flexible, “tendon cable” soft robot arm to a conventional Cartesian three axis 3D printing carousel. This allows printing along a combination of Cartesian and curvilinear coordinates using five independent stepper motors controlled by an Arduino Uno with each motor requiring a microstep driver powered via a 12 V power supply. Three of the independent motors control the printing head motion along conventional Cartesian coordinates while two of the independent motors control the length of each pair of the four “tendon cables” which in turn controls the radius of curvature and the angle displacement of the soft printer head along two orthogonal planes. This combination imparts motion along six independent degrees-of-freedom in Cartesian and curvilinear coordinates. The design of the system is described together with experimental results, which demonstrate that this design can print continuously along curved and inclined surfaces while avoiding the “staircase” effect, which is typical of conventional three axis 3D printing along curvilinear surfaces.
- 5 August 2022
- Published by ASME International in Journal of Medical Devices
- Vol. 16 (4)
Three-Dimensional Printing in Combined Cartesian and Curvilinear Coordinates
A three-dimensional (3D) printing technology that facilitates continuous printing along a combination of Cartesian and curvilinear coordinates, designed for in vivo and in situ bioprinting, is introduced. The combined Cartesian/curvilinear printing head motion is accomplished by attaching a biomimetic, flexible, “tendon cable” soft robot arm to a conventional Cartesian three axis 3D printing carousel. This allows printing along a combination of Cartesian and curvilinear coordinates using five independent stepper motors controlled by an Arduino Uno with each motor requiring a microstep driver powered via a 12 V power supply. Three of the independent motors control the printing head motion along conventional Cartesian coordinates while two of the independent motors control the length of each pair of the four “tendon cables” which in turn controls the radius of curvature and the angle displacement of the soft printer head along two orthogonal planes. This combination imparts motion along six independent degrees-of-freedom in Cartesian and curvilinear coordinates. The design of the system is described together with experimental results, which demonstrate that this design can print continuously along curved and inclined surfaces while avoiding the “staircase” effect, which is typical of conventional three axis 3D printing along curvilinear surfaces.
- 18 January 2022
- Published by Wiley in Journal of Heat Transfer
- Vol. 144 (3)
A Modular Three-Dimensional Bioprinter for Printing Porous Scaffolds for Tissue Engineering
Three-dimensional (3D) bioprinting is a fabrication method with many biomedical applications, particularly within tissue engineering. The use of freezing during 3D bioprinting, aka “3D cryoprinting,” can be utilized to create micopores within tissue-engineered scaffolds to enhance cell proliferation. When used with alginate bio-inks, this type of 3D cryoprinting requires three steps: 3D printing, crosslinking, and freezing. This study investigated the influence of crosslinking order and cooling rate on the microstructure and mechanical properties of sodium alginate scaffolds. We designed and built a novel modular 3D printer in order to study the effects of these steps separately and to address many of the manufacturing issues associated with 3D cryoprinting. With the modular 3D printer, 3D printing, crosslinking, and freezing were conducted on separate modules yet remain part of a continuous manufacturing process. Crosslinking before the freezing step produced highly interconnected and directional pores, which are ideal for promoting cell growth. By controlling the cooling rate, it was possible to produce pores with diameters from a range of 5 μm to 40 μm. Tensile and firmness testing found that the use of freezing does not decrease the tensile strength of the printed objects, though there was a significant loss in firmness for strands with larger pores.
- 18 January 2022
- Published by Wiley in Journal of Heat Transfer
- Vol. 144 (3)
A Modular Three-Dimensional Bioprinter for Printing Porous Scaffolds for Tissue Engineering
Three-dimensional (3D) bioprinting is a fabrication method with many biomedical applications, particularly within tissue engineering. The use of freezing during 3D bioprinting, aka “3D cryoprinting,” can be utilized to create micopores within tissue-engineered scaffolds to enhance cell proliferation. When used with alginate bio-inks, this type of 3D cryoprinting requires three steps: 3D printing, crosslinking, and freezing. This study investigated the influence of crosslinking order and cooling rate on the microstructure and mechanical properties of sodium alginate scaffolds. We designed and built a novel modular 3D printer in order to study the effects of these steps separately and to address many of the manufacturing issues associated with 3D cryoprinting. With the modular 3D printer, 3D printing, crosslinking, and freezing were conducted on separate modules yet remain part of a continuous manufacturing process. Crosslinking before the freezing step produced highly interconnected and directional pores, which are ideal for promoting cell growth. By controlling the cooling rate, it was possible to produce pores with diameters from a range of 5 μm to 40 μm. Tensile and firmness testing found that the use of freezing does not decrease the tensile strength of the printed objects, though there was a significant loss in firmness for strands with larger pores.
- Open Access
- 18 December 2021
- Published by MDPI AG in Micromachines
- Vol. 12 (12) , 1578
Individual Microparticle Manipulation Using Combined Electroosmosis and Dielectrophoresis through a Si3N4 Film with a Single Micropore
Porous dielectric membranes that perform insulator-based dielectrophoresis or electroosmotic pumping are commonly used in microchip technologies. However, there are few fundamental studies on the electrokinetic flow patterns of single microparticles around a single micropore in a thin dielectric film. Such a study would provide fundamental insights into the electrokinetic phenomena around a micropore, with practical applications regarding the manipulation of single cells and microparticles by focused electric fields. We have fabricated a device around a silicon nitride film with a single micropore (2–4 µm in diameter) which has the ability to locally focus electric fields on the micropore. Single microscale polystyrene beads were used to study the electrokinetic flow patterns. A mathematical model was developed to support the experimental study and evaluate the electric field distribution, fluid motion, and bead trajectories. Good agreement was found between the mathematic model and the experimental data. We show that the combination of electroosmotic flow and dielectrophoretic force induced by direct current through a single micropore can be used to trap, agglomerate, and repel microparticles around a single micropore without an external pump. The scale of our system is practically relevant for the manipulation of single mammalian cells, and we anticipate that our single-micropore approach will be directly employable in applications ranging from fundamental single cell analyses to high-precision single cell electroporation or cell fusion.
- 18 December 2021
- Published by MDPI AG in Micromachines
- Vol. 12 (12) , 1578
Open AccessIndividual Microparticle Manipulation Using Combined Electroosmosis and Dielectrophoresis through a Si3N4 Film with a Single Micropore
Porous dielectric membranes that perform insulator-based dielectrophoresis or electroosmotic pumping are commonly used in microchip technologies. However, there are few fundamental studies on the electrokinetic flow patterns of single microparticles around a single micropore in a thin dielectric film. Such a study would provide fundamental insights into the electrokinetic phenomena around a micropore, with practical applications regarding the manipulation of single cells and microparticles by focused electric fields. We have fabricated a device around a silicon nitride film with a single micropore (2–4 µm in diameter) which has the ability to locally focus electric fields on the micropore. Single microscale polystyrene beads were used to study the electrokinetic flow patterns. A mathematical model was developed to support the experimental study and evaluate the electric field distribution, fluid motion, and bead trajectories. Good agreement was found between the mathematic model and the experimental data. We show that the combination of electroosmotic flow and dielectrophoretic force induced by direct current through a single micropore can be used to trap, agglomerate, and repel microparticles around a single micropore without an external pump. The scale of our system is practically relevant for the manipulation of single mammalian cells, and we anticipate that our single-micropore approach will be directly employable in applications ranging from fundamental single cell analyses to high-precision single cell electroporation or cell fusion.