Kyryl Volodymyrovych Shevchenko
Research Subjects
Kyryl Volodymyrovych Shevchenko has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Andrii Grigorov
National Technical University “Kharkiv Polytechnic Institute
2 shared publications Andrey Hrigorov
1 shared publicationAndrii Hryhorov
1 shared publication- Irina Valeriivna Sinkevich
Національний технічний університет «Харківський політехнічний інститут
1 shared publication
Latest Publications
- 27 March 2026
- Published by National Technical University Kharkiv Polytechnic Institute in Integrated Technologies and Energy Saving
- No. 1,p. 19-31
HYDROGENATION PROCESSING OF WASTE LUBRICATING OILS INTO COMPONENTS OF AUTOMOTIVE GASOLINES
The article proposes to expand the raw material base for the production of automobile gasoline by using such a massive industrial waste as used lubricating oils, which, together with a valuable source of hydrocarbon raw materials, are a rather dangerous substance for the environment. For the processing of the specified raw materials, the possibility of using hydrogenation processes, in particular hydrocracking, which allows modifying the chemical com-position of hydrocarbons with simultaneous stabilization due to the presence of hydrogen, has been analyzed. Taking into account the peculiarities of the chemical composition of used lu-bricating oils, before hydrocracking, it is necessary to carry out special preparation of the raw materials, which consists in removing polluting impurities and hydrocarbon oxidation prod-ucts to the following level: water content (< 1 %); mechanical impurities content (< 0.5 %); Zn, Ca, Pb, Al content (< 0.01 %); hydrocarbon base content –C15–C35 (> 90 %); content of resins and asphaltenes (< 3 %). Also, for hydrocracking of used lubricating oils, it is neces-sary to use a catalyst resistant to metal poisoning and coking. As such catalysts, bifunctional catalysts represented by metals (Ni, Mo, W, Pt) and a base (zeolites, γ-Al₂O₃) should be used. Among commercial catalysts for hydrocracking of used oils, it is advisable to use Criterion DN-190 (Ni-Mo/Al₂O₃), TK-607 / TK-747 (Ni-W / Al₂O₃), ACT 452 (Ni-W/Zeolite) or HRK-103 (Pt/USY). As a result of hydrocracking on the specified catalysts, it is possible to obtain a product – a gasoline fraction (C5–C12), which, in terms of its chemical composition and re-lated properties (for example, octane number at the level of (MON 60–70), requires a com-pounding stage with high-octane components (alkylate, isomerizate or reformate) to increase the octane number (to ≥ 82.5 MON) in accordance with the requirements of DSTU 7687:2015 "AUTOMOTIVE EURO GASOLINES. Technical conditions".
- 27 March 2026
- Published by National Technical University Kharkiv Polytechnic Institute in Integrated Technologies and Energy Saving
- No. 1,p. 19-31
HYDROGENATION PROCESSING OF WASTE LUBRICATING OILS INTO COMPONENTS OF AUTOMOTIVE GASOLINES
The article proposes to expand the raw material base for the production of automobile gasoline by using such a massive industrial waste as used lubricating oils, which, together with a valuable source of hydrocarbon raw materials, are a rather dangerous substance for the environment. For the processing of the specified raw materials, the possibility of using hydrogenation processes, in particular hydrocracking, which allows modifying the chemical com-position of hydrocarbons with simultaneous stabilization due to the presence of hydrogen, has been analyzed. Taking into account the peculiarities of the chemical composition of used lu-bricating oils, before hydrocracking, it is necessary to carry out special preparation of the raw materials, which consists in removing polluting impurities and hydrocarbon oxidation prod-ucts to the following level: water content (< 1 %); mechanical impurities content (< 0.5 %); Zn, Ca, Pb, Al content (< 0.01 %); hydrocarbon base content –C15–C35 (> 90 %); content of resins and asphaltenes (< 3 %). Also, for hydrocracking of used lubricating oils, it is neces-sary to use a catalyst resistant to metal poisoning and coking. As such catalysts, bifunctional catalysts represented by metals (Ni, Mo, W, Pt) and a base (zeolites, γ-Al₂O₃) should be used. Among commercial catalysts for hydrocracking of used oils, it is advisable to use Criterion DN-190 (Ni-Mo/Al₂O₃), TK-607 / TK-747 (Ni-W / Al₂O₃), ACT 452 (Ni-W/Zeolite) or HRK-103 (Pt/USY). As a result of hydrocracking on the specified catalysts, it is possible to obtain a product – a gasoline fraction (C5–C12), which, in terms of its chemical composition and re-lated properties (for example, octane number at the level of (MON 60–70), requires a com-pounding stage with high-octane components (alkylate, isomerizate or reformate) to increase the octane number (to ≥ 82.5 MON) in accordance with the requirements of DSTU 7687:2015 "AUTOMOTIVE EURO GASOLINES. Technical conditions".
- 22 May 2024
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University "KhPI". Series: Chemistry, Chemical Technology and Ecology
- No. 1(11),p. 84-88
FEATURES OF RECEIVING THE GASOLINE FRACTION BY THERMAL PYROLYSIS OF POLYOLEFIN RAW MATERIALS
The article examines the peculiarities of the process of thermal pyrolysis of secondary polymer raw materials, aimed at obtaining a gasoline fraction - the basis for obtaining mixed or synthetic automobile gasoline. Based on the global experience of polymer processing, polyolefins represented by high-density polyethylene (HDLP) and polypropylene (PP) were chosen for the study. Thermal pyrolysis was carried out at atmospheric pressure (0.10-0.12 MPa) on a reactor-type laboratory installation with subsequent removal of the gasoline fraction (30-210 °C) from liquid pyrolysis products according to the ASTM D 86 method. It has been established that the temperature interval in which pyrolysis of polyolefin raw materials must be carried out is for HDLP - 400-430 °С (the maximum output of the gasoline fraction at 420 °С); for PP - 350-370 °C (maximum yield of gasoline fraction at 365 °C). By controlling the duration of thermal pyrolysis, it is possible to increase the yield of the gasoline fraction by an average of 15-17%, which must be taken into account during the industrial implementation and further operation of pyrolysis plants for polymer raw materials. Increasing the temperature of the end of boiling of the gasoline fraction from 150 °С to 210 °С allows to increase its output by 9% (for HDLP) and by 12% (for PP). But at the same time, there is also an increase in the content of olefins in it (by 13-14%), which is a positive point from the point of view of resistance to detonation of the gasoline fraction, and a negative point - in view of its low chemical stability. The conducted studies showed that secondary polyolefin raw materials should be considered as an alternative to classic raw materials (oil and gas condensate), and the pyrolysis process as the main technological process for obtaining the gasoline fraction - the basis for obtaining commercial automobile gasoline. Prospective places for the implementation of this technology are both production sites of oil refineries and sites located in close proximity to places of accumulation of raw materials - ports, city landfills, special landfills. В статті розглянуто особливості проведення процесу термічного піролізу вторинної полімерної сировини, спрямованого на отримання бензинової фракції – бази для отримання сумішевого або синтетичного автомобільного бензину. Спираючись на світовий досвід переробки полімерів, для дослідження було обрано поліолефіни, представлені поліетиленом високої густини (HDLP) та поліпропілен (РР). Термічний піроліз проводили при атмосферному тиску (0,10-0,12 МПа) на лабораторній установці реакторного типу з подальшим видаленням бензинової фракції (30-210 °С) із рідких продуктів піролізу за методом ASTM D 86. Встановлено, що температурний інтервал, в якому необхідно проводити піроліз поліолефінової сировини, складає для HDLP – 400-430°С (максимальний вихід бензинової фракції при 420°С); для РР - 350-370 °С (максимальний вихід бензинової фракції при 365 °С). Керуючи тривалість термічного піролізу можна збільшити вихід бензинової фракції у середньому на 15-17 %, що необхідно враховувати при промисловому впровадженні та подальшій експлуатації установок піролізу полімерної сировини. Збільшення температури кінця кипіння бензинової фракції з 150 °С до 210 °С дозволяє збільшити її вихід на 9 % (для HDLP) і на 12 % (для РР). Але відповідно спостерігається і збільшення вмісту у ній олефінів (на 13-14 %), що є позитивним моментом з точки зору стійкості до детонації бензинової фракції і негативним – з огляду на низьку її хімічну стабільність. Проведені дослідження показали, що вторинну поліолефінову сировину необхідно розглядати як альтернативну до класичної сировини (нафти та газового конденсату), а процес піролізу як основний технологічний процес отримання бензинової фракції – бази для отримання товарного автомобільного бензину. Перспективними місцями реалізації даної технології є як виробничі майданчики нафтопереробних заводів, так і майданчики, розташовані у безпосередньої близькості до місць накопичення сировини – портів, міських сміттєзвалищ, спеціальних полігонів.
- 22 May 2024
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University "KhPI". Series: Chemistry, Chemical Technology and Ecology
- No. 1(11),p. 84-88
FEATURES OF RECEIVING THE GASOLINE FRACTION BY THERMAL PYROLYSIS OF POLYOLEFIN RAW MATERIALS
The article examines the peculiarities of the process of thermal pyrolysis of secondary polymer raw materials, aimed at obtaining a gasoline fraction - the basis for obtaining mixed or synthetic automobile gasoline. Based on the global experience of polymer processing, polyolefins represented by high-density polyethylene (HDLP) and polypropylene (PP) were chosen for the study. Thermal pyrolysis was carried out at atmospheric pressure (0.10-0.12 MPa) on a reactor-type laboratory installation with subsequent removal of the gasoline fraction (30-210 °C) from liquid pyrolysis products according to the ASTM D 86 method. It has been established that the temperature interval in which pyrolysis of polyolefin raw materials must be carried out is for HDLP - 400-430 °С (the maximum output of the gasoline fraction at 420 °С); for PP - 350-370 °C (maximum yield of gasoline fraction at 365 °C). By controlling the duration of thermal pyrolysis, it is possible to increase the yield of the gasoline fraction by an average of 15-17%, which must be taken into account during the industrial implementation and further operation of pyrolysis plants for polymer raw materials. Increasing the temperature of the end of boiling of the gasoline fraction from 150 °С to 210 °С allows to increase its output by 9% (for HDLP) and by 12% (for PP). But at the same time, there is also an increase in the content of olefins in it (by 13-14%), which is a positive point from the point of view of resistance to detonation of the gasoline fraction, and a negative point - in view of its low chemical stability. The conducted studies showed that secondary polyolefin raw materials should be considered as an alternative to classic raw materials (oil and gas condensate), and the pyrolysis process as the main technological process for obtaining the gasoline fraction - the basis for obtaining commercial automobile gasoline. Prospective places for the implementation of this technology are both production sites of oil refineries and sites located in close proximity to places of accumulation of raw materials - ports, city landfills, special landfills. В статті розглянуто особливості проведення процесу термічного піролізу вторинної полімерної сировини, спрямованого на отримання бензинової фракції – бази для отримання сумішевого або синтетичного автомобільного бензину. Спираючись на світовий досвід переробки полімерів, для дослідження було обрано поліолефіни, представлені поліетиленом високої густини (HDLP) та поліпропілен (РР). Термічний піроліз проводили при атмосферному тиску (0,10-0,12 МПа) на лабораторній установці реакторного типу з подальшим видаленням бензинової фракції (30-210 °С) із рідких продуктів піролізу за методом ASTM D 86. Встановлено, що температурний інтервал, в якому необхідно проводити піроліз поліолефінової сировини, складає для HDLP – 400-430°С (максимальний вихід бензинової фракції при 420°С); для РР - 350-370 °С (максимальний вихід бензинової фракції при 365 °С). Керуючи тривалість термічного піролізу можна збільшити вихід бензинової фракції у середньому на 15-17 %, що необхідно враховувати при промисловому впровадженні та подальшій експлуатації установок піролізу полімерної сировини. Збільшення температури кінця кипіння бензинової фракції з 150 °С до 210 °С дозволяє збільшити її вихід на 9 % (для HDLP) і на 12 % (для РР). Але відповідно спостерігається і збільшення вмісту у ній олефінів (на 13-14 %), що є позитивним моментом з точки зору стійкості до детонації бензинової фракції і негативним – з огляду на низьку її хімічну стабільність. Проведені дослідження показали, що вторинну поліолефінову сировину необхідно розглядати як альтернативну до класичної сировини (нафти та газового конденсату), а процес піролізу як основний технологічний процес отримання бензинової фракції – бази для отримання товарного автомобільного бензину. Перспективними місцями реалізації даної технології є як виробничі майданчики нафтопереробних заводів, так і майданчики, розташовані у безпосередньої близькості до місць накопичення сировини – портів, міських сміттєзвалищ, спеціальних полігонів.
- 15 May 2021
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University "KhPI". Series: Chemistry, Chemical Technology and Ecology
- No. 1(5),p. 51-55
FLAMMABILITY OF HYDROCARBON FRACTIONS OBTAINED BY DESTRUCTION OF POLYMER RAW MATERIALS
The article discusses the possibility of using hydrocarbon fractions – products of thermal destruction of polymer raw materials (polyethylene and polypropylene) at atmospheric pressure as components of commercial diesel fuels. This approach allows, on the one hand, to improve the properties of commercial diesel fuel, on the other, to increase the competitiveness of domestically produced products. In addition, the problem associated with the accumulation of polymer waste and their negative impact on the environment is also partially solved. The nature of the dependences between such indicators of the quality of fractions 160–350 °C, 200–350 °C, 240–350 °C as the autoignition temperature, the initial boiling point of the fraction and the cetane number as an indicator characterizing the flammability, has been established. The dependence of the autoignition temperature on the boiling point of the fractions has a polynomial character and indicates a decrease in the autoignition temperature with an increase in the boiling point of the fractions. The dependence of the cetane number on the initial boiling point of the fractions is linear and indicates an increase in the cetane number with an increase in the initial boiling point of the fractions. The dependence of the cetane number on the autoignition temperature of the fractions has a polynomial character and indicates a decrease in the cetane number with an increase in the autoignition temperature of the fractions. It was found that the autoignition temperature of the investigated fractions, regardless of the type of polymer raw material, fluctuates in a rather narrow range, from 229 to 348 ° C, and the cetane number – from 41 to 55 units. Based on the literature data, we note that exactly this range is close to the range that commercial diesel fuels have, and the fractions studied by us can be used in the production of diesel fuel.
- 15 May 2021
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University "KhPI". Series: Chemistry, Chemical Technology and Ecology
- No. 1(5),p. 51-55
FLAMMABILITY OF HYDROCARBON FRACTIONS OBTAINED BY DESTRUCTION OF POLYMER RAW MATERIALS
The article discusses the possibility of using hydrocarbon fractions – products of thermal destruction of polymer raw materials (polyethylene and polypropylene) at atmospheric pressure as components of commercial diesel fuels. This approach allows, on the one hand, to improve the properties of commercial diesel fuel, on the other, to increase the competitiveness of domestically produced products. In addition, the problem associated with the accumulation of polymer waste and their negative impact on the environment is also partially solved. The nature of the dependences between such indicators of the quality of fractions 160–350 °C, 200–350 °C, 240–350 °C as the autoignition temperature, the initial boiling point of the fraction and the cetane number as an indicator characterizing the flammability, has been established. The dependence of the autoignition temperature on the boiling point of the fractions has a polynomial character and indicates a decrease in the autoignition temperature with an increase in the boiling point of the fractions. The dependence of the cetane number on the initial boiling point of the fractions is linear and indicates an increase in the cetane number with an increase in the initial boiling point of the fractions. The dependence of the cetane number on the autoignition temperature of the fractions has a polynomial character and indicates a decrease in the cetane number with an increase in the autoignition temperature of the fractions. It was found that the autoignition temperature of the investigated fractions, regardless of the type of polymer raw material, fluctuates in a rather narrow range, from 229 to 348 ° C, and the cetane number – from 41 to 55 units. Based on the literature data, we note that exactly this range is close to the range that commercial diesel fuels have, and the fractions studied by us can be used in the production of diesel fuel.
- 14 December 2020
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University "KhPI". Series: Chemistry, Chemical Technology and Ecology
- No. 2 (4),p. 75-79
INVESTIGATION OF CORROSIVE EFFECT ON METAL OF A BROAD FUEL FRACTION OBTAINED FROM SECONDARY POLYMER RAW MATERIAL
A research of the corrosion effect on the metal (copper plate) of a broad fuel fraction (FPF) - a liquid product of thermal destruction of secondary raw materials made of low pressure polyethylene (LDPE) at temperatures up to 380 ° C and a pressure of 0,12-0,15 MPa. is conducted. Determination of the corrosion effect on the copper FFT plate was carried out in accordance with the standard ASTM D 130-10 at a temperature of 50 ° C for 120 minutes for both the dehydrated FFT sample and in the presence of 1% water. It was found that the copper plates, which were in the FFT and FFT + 1% water in the visual evaluation, had a light orange color, close to the color of the original plate. This, in turn, indicates that the investigated FFT samples have withstood the test, and the corrosive effect on the copper plate can be attributed to a slight fading, class 1.a. Also, together with the study under standard conditions, the corrosion effect on the copper plate of the products of combustion of FFT at different temperatures at which it was found that in the temperature range 180-230 ° C the surface of the copper plate becomes pale purple, and the corrosion effect on the copper plate can be attributed to moderate dimming, class 2.b; at temperatures of 230-290 ° the surface of the copper plate already has a silver color, and the corrosive effect on the copper plate corresponds to a moderate blackout, class 2.d. Therefore, when the combustion products of the FFT on the copper plate only oxygen corrosion occurs, which is due to the presence of oxygen in the area of the copper plate and the temperature of the combustion products. Thus, it was concluded that there is no corrosive elements in the FFT, which makes it suitable for use as a cheap component of motor, furnace and boiler fuels, improving their performance (e.g., reducing sulfur content).
- 14 December 2020
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University "KhPI". Series: Chemistry, Chemical Technology and Ecology
- No. 2 (4),p. 75-79
INVESTIGATION OF CORROSIVE EFFECT ON METAL OF A BROAD FUEL FRACTION OBTAINED FROM SECONDARY POLYMER RAW MATERIAL
A research of the corrosion effect on the metal (copper plate) of a broad fuel fraction (FPF) - a liquid product of thermal destruction of secondary raw materials made of low pressure polyethylene (LDPE) at temperatures up to 380 ° C and a pressure of 0,12-0,15 MPa. is conducted. Determination of the corrosion effect on the copper FFT plate was carried out in accordance with the standard ASTM D 130-10 at a temperature of 50 ° C for 120 minutes for both the dehydrated FFT sample and in the presence of 1% water. It was found that the copper plates, which were in the FFT and FFT + 1% water in the visual evaluation, had a light orange color, close to the color of the original plate. This, in turn, indicates that the investigated FFT samples have withstood the test, and the corrosive effect on the copper plate can be attributed to a slight fading, class 1.a. Also, together with the study under standard conditions, the corrosion effect on the copper plate of the products of combustion of FFT at different temperatures at which it was found that in the temperature range 180-230 ° C the surface of the copper plate becomes pale purple, and the corrosion effect on the copper plate can be attributed to moderate dimming, class 2.b; at temperatures of 230-290 ° the surface of the copper plate already has a silver color, and the corrosive effect on the copper plate corresponds to a moderate blackout, class 2.d. Therefore, when the combustion products of the FFT on the copper plate only oxygen corrosion occurs, which is due to the presence of oxygen in the area of the copper plate and the temperature of the combustion products. Thus, it was concluded that there is no corrosive elements in the FFT, which makes it suitable for use as a cheap component of motor, furnace and boiler fuels, improving their performance (e.g., reducing sulfur content).