You Qian
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
You Qian has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Chengkuo Lee
Department of Electrical and Computer Engineering National University of Singapore Singapore
16 shared publications Yu-Sheng Lin
Department of Electrical and Computer Engineering, National University of Singapore, Singapore
5 shared publications- Chong Pei Ho
The University of Tokyo
4 shared publications Navab Singh
Institute of Microelectronics (Singapore)
4 shared publicationsPrakash Pitchappa
National Univ. of Singapore (Singapore)
4 shared publicationsBo Woon Soon
Department of Electrical and Computer Engineering, National University of Singapore, 4 Engineering Drive 3, Singapore 117576
3 shared publications
Latest Publications
- 19 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Nanotechnology Magazine
- Vol. 18 (1) , 23-33
Acoustic Filters for RF Communication
- 19 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Nanotechnology Magazine
- Vol. 18 (1) , 23-33
Acoustic Filters for RF Communication
- 4 March 2015
- Published by SPIE-Intl Soc Optical Eng
- Vol. 9302, 93021I-93021I-6
MEMS switchable infrared metamaterial absorber
- 4 March 2015
- Published by SPIE-Intl Soc Optical Eng
- Vol. 9302, 93021I-93021I-6
MEMS switchable infrared metamaterial absorber
- 1 January 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1032-1035
Enhanced controllability in MEMS metamaterial
In this report, we demonstrate a method to enhance the controllability of MEMS tunable metamaterial by isolating the electrical routing of alternate lines in the metamaterial unit cell array. The metamaterial consists of alternate lines of split ring resonators with two released heights. This allows for two independent tuning characteristics for a single MEMS metamaterial by selecting between the two external control ports. This technology can be further improved to provide line or pixel wise control, and can even be programmed to have one of many functionalities such as tunable filter, multicolor spatial modulator, gradient metamaterial or random metamaterial.
- 1 January 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1032-1035
Enhanced controllability in MEMS metamaterial
In this report, we demonstrate a method to enhance the controllability of MEMS tunable metamaterial by isolating the electrical routing of alternate lines in the metamaterial unit cell array. The metamaterial consists of alternate lines of split ring resonators with two released heights. This allows for two independent tuning characteristics for a single MEMS metamaterial by selecting between the two external control ports. This technology can be further improved to provide line or pixel wise control, and can even be programmed to have one of many functionalities such as tunable filter, multicolor spatial modulator, gradient metamaterial or random metamaterial.
- 17 April 2014
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 6 (11) , 5606-5611
All metal nanoelectromechanical switch working at 300 °C for rugged electronics applications
An all metal based electrostatic nanoelectromechanical switch has been fabricated using a one mask process. High temperature cycling behavior is demonstrated in a vacuum chamber at 300 °C for more than 28 hours. The compelling results indicate that the design is promising for the realization of rugged electronics with three-dimensional integration.
- 17 April 2014
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 6 (11) , 5606-5611
All metal nanoelectromechanical switch working at 300 °C for rugged electronics applications
An all metal based electrostatic nanoelectromechanical switch has been fabricated using a one mask process. High temperature cycling behavior is demonstrated in a vacuum chamber at 300 °C for more than 28 hours. The compelling results indicate that the design is promising for the realization of rugged electronics with three-dimensional integration.
- 12 March 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 23 (5) , 1121-1130
Fabrication and Characterization of a Vacuum Encapsulated Curved Beam Switch for Harsh Environment Application
A vacuum-encapsulated silicon switch with a curved electrode is characterized for operation in harsh environments. An ultraclean vacuum encapsulation process (episeal) seals the switch after release, providing a pristine operating environment for switching operations. In these devices, the curved beam of the actuator enhances the overdrive voltage tolerance to be more than 100 V. The ON/OFF cycle tests were carried out up to 10 5 cycles at room temperature, and at least 10 4 cycles under an elevated temperature of 300°C. Throughout the 300°C tests, an average contact resistance of ~ 28 kΩ is measured, demonstrating the stability of the contact. Finally, high speed pulse I-V monitoring unit was used to observe 13-μs switching speed.
- 12 March 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 23 (5) , 1121-1130
Fabrication and Characterization of a Vacuum Encapsulated Curved Beam Switch for Harsh Environment Application
A vacuum-encapsulated silicon switch with a curved electrode is characterized for operation in harsh environments. An ultraclean vacuum encapsulation process (episeal) seals the switch after release, providing a pristine operating environment for switching operations. In these devices, the curved beam of the actuator enhances the overdrive voltage tolerance to be more than 100 V. The ON/OFF cycle tests were carried out up to 10 5 cycles at room temperature, and at least 10 4 cycles under an elevated temperature of 300°C. Throughout the 300°C tests, an average contact resistance of ~ 28 kΩ is measured, demonstrating the stability of the contact. Finally, high speed pulse I-V monitoring unit was used to observe 13-μs switching speed.
- 1 December 2013
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 204, 37-43
A multi-frequency vibration-based MEMS electromagnetic energy harvesting device
- 1 December 2013
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 204, 37-43
A multi-frequency vibration-based MEMS electromagnetic energy harvesting device
- 2 October 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 23 (3) , 740-749
An In-Plane Approximated Nonlinear MEMS Electromagnetic Energy Harvester
This paper presents the fabrication, modeling, and characterization of an in-plane approximated nonlinear MEMS electromagnetic energy harvester (EM-EH) device. The approximated nonlinearity and frequency broadening of the device are realized by incorporating small suspension structures, which introduces the spring hardening effect and thus increases the operating frequency of the device toward a higher frequency interval. From the experimental results, the resonant frequencies during frequency up-sweep have been shifted from the original resonance of 82 Hz to 123.5, 135, and 146.5 Hz, at the accelerations of 1.0, 2.0 and 3.0 g, respectively. The corresponding power densities at resonances are 1.6 × 10-8, 2.8 × 10 -8 , and 5.6 × 10 -8 W/cm 3 . This paper offers a new design methodology of the approximated nonlinear MEMS EM-EH device.
- 2 October 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 23 (3) , 740-749
An In-Plane Approximated Nonlinear MEMS Electromagnetic Energy Harvester
This paper presents the fabrication, modeling, and characterization of an in-plane approximated nonlinear MEMS electromagnetic energy harvester (EM-EH) device. The approximated nonlinearity and frequency broadening of the device are realized by incorporating small suspension structures, which introduces the spring hardening effect and thus increases the operating frequency of the device toward a higher frequency interval. From the experimental results, the resonant frequencies during frequency up-sweep have been shifted from the original resonance of 82 Hz to 123.5, 135, and 146.5 Hz, at the accelerations of 1.0, 2.0 and 3.0 g, respectively. The corresponding power densities at resonances are 1.6 × 10-8, 2.8 × 10 -8 , and 5.6 × 10 -8 W/cm 3 . This paper offers a new design methodology of the approximated nonlinear MEMS EM-EH device.
- 1 August 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 167-168
Tunable THz filter using 3-D split-ring resonators
An electrically tunable MEMS based out-of-plane metamaterials THz filter using stress-induced curved cantilevers to form split-ring resonator in three-dimensional configuration is experimentally demonstrated and characterized. While the achieved tunable range for the resonant frequency is 0.5 THz at 20 volts bias, quality factor of the resonant frequency is improved as well. This MEMS based THz filter using curved cantilevers shows its potential in tunable metamaterials applications such as sensors, optical switches, and filters, etc.
- 1 August 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 167-168
Tunable THz filter using 3-D split-ring resonators
An electrically tunable MEMS based out-of-plane metamaterials THz filter using stress-induced curved cantilevers to form split-ring resonator in three-dimensional configuration is experimentally demonstrated and characterized. While the achieved tunable range for the resonant frequency is 0.5 THz at 20 volts bias, quality factor of the resonant frequency is improved as well. This MEMS based THz filter using curved cantilevers shows its potential in tunable metamaterials applications such as sensors, optical switches, and filters, etc.
- 1 August 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 141-142
Development of tunable 3-D eSRR for THz applications
Structurally reconfigurable metamaterials showing terahertz frequency tunability are presented. The proposed metamaterial structures employ deformable microelectromechanical system based curved cantilevers for tuning the resonance frequency of the electric split-ring resonators. The observed tunability has been demonstrated by both the electromagnetic simulation and the experimental measurement.
- 1 August 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 141-142
Development of tunable 3-D eSRR for THz applications
Structurally reconfigurable metamaterials showing terahertz frequency tunability are presented. The proposed metamaterial structures employ deformable microelectromechanical system based curved cantilevers for tuning the resonance frequency of the electric split-ring resonators. The observed tunability has been demonstrated by both the electromagnetic simulation and the experimental measurement.
- 29 July 2013
- Published by AIP Publishing in Applied Physics Letters
- Vol. 103 (5) , 053122
A bi-stable nanoelectromechanical non-volatile memory based on van der Waals force
By using complementary-metal-oxide-semiconductor processes, a silicon based bi-stable nanoelectromechanical non-volatile memory is fabricated and characterized. The main feature of this device is an 80 nm wide and 3 μm high silicon nanofin (SiNF) of a high aspect ratio (1:35). The switching mechanism is realized by electrostatic actuation between two lateral electrodes, i.e., terminals. Bi-stable hysteresis behavior is demonstrated when the SiNF maintains its contact to one of the two terminals by leveraging on van der Waals force even after voltage bias is turned off. The compelling results indicate that this design is promising for realization of high density non-volatile memory application due to its nano-scale footprint and zero on-hold power consumption.
- 29 July 2013
- Published by AIP Publishing in Applied Physics Letters
- Vol. 103 (5) , 053122
A bi-stable nanoelectromechanical non-volatile memory based on van der Waals force
By using complementary-metal-oxide-semiconductor processes, a silicon based bi-stable nanoelectromechanical non-volatile memory is fabricated and characterized. The main feature of this device is an 80 nm wide and 3 μm high silicon nanofin (SiNF) of a high aspect ratio (1:35). The switching mechanism is realized by electrostatic actuation between two lateral electrodes, i.e., terminals. Bi-stable hysteresis behavior is demonstrated when the SiNF maintains its contact to one of the two terminals by leveraging on van der Waals force even after voltage bias is turned off. The compelling results indicate that this design is promising for realization of high density non-volatile memory application due to its nano-scale footprint and zero on-hold power consumption.