Szymon Gądek
Research Subjects
Research Interests
Szymon Gądek has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Dariusz Mierzwiński
Faculty of Materials Engineering and Physics, Department of Materials Science, Cracow University of Technology, Krakow, Poland, Poland
3 shared publications - A.-M. Vasylieva
Department of Materials Science and Engineering, Lviv Polytechnic National University, 12 S. Bandera Str., Lviv, 79013, Ukraine
1 shared publication Aleksandra Borucka
Faculty of Materials Science and Physics, Cracow University of Technology, Kraków, Poland
1 shared publicationDoan Hung Tran
Faculty of Mechanical Engineering, Nha Trang Universit
1 shared publication- Karolina Mazur
Faculty of Materials Engineering and Physics, Institute of Materials Engineering, Tadeusz Kosciuszko Cracow University of Technology, Al. Jana Pawła II 37, 31-864 Cracow, Poland
1 shared publication - Kinga Korniejenko
Cracow University of Technology
1 shared publication
Latest Publications
- 1 January 2025
- Published by Index Copernicus in Journal of Achievements in Materials and Manufacturing Engineering
- Vol. 128 (1) , 5-17
Tribological properties of PLA-based composites produced by 3D printing
The current trends in the development of additive technologies, which are actively used in various industries, have been analysed. Special attention was found to be paid to polylactic acid (PLA), an environmentally friendly and biodegradable polymer widely used in 3D printing due to its low melting point and cost-effectiveness. The tribological properties of PLA were improved by adding clay in different concentrations and changing the filling type during printing. The highest indicators of wear resistance and the minimum coefficient of friction were found in the PLA/0.1Clay composite with Grid 90/85 filling. Such a type of filling provided optimal tribological properties for all composites due to the implementation of an abrasive wear mechanism accompanied by plastic deformation. It was revealed that the introduction of clay plasticized the material, which resulted in the widening of the sliding tracks.Pure PLA and PLA/Clay composites with different clay concentrations (0.1, 0.2, 0.3 g per 50 g PLA) were used for the study. The samples were printed with Sphere/100, Grid 90/100 and Grid 90/85 infill to study the effect of structure and density on tribological properties. Density, clay distribution (SEM), tribological tests, as well as wear track structure and friction mechanisms were investigated. The nature of clay distribution in the obtained filaments was evaluated by scanning electron microscopy (SEM) on a JSM-IT200 scanning electron microscope (Tokyo, Japan). To establish the elemental composition of the clay used to create the filaments, X-ray fluorescence analysis was performed on a CEP-01 Elvax Light X-ray spectrometer. The hardness of the samples was measured by indentation according to the Shore method on the Shore hardness tester HT-6510D. Tribological studies of the obtained samples were carried out according to the ball-on-disk scheme on the Tester T-01M computerized friction machine. The microstructure of the surfaces of the studied samples was analysed using an MBS-9 microscope.The influence of the chemical composition of PLA/Clay and the type of filler on the tribological characteristics, including wear resistance, wear intensity and friction mechanisms, was evaluated. The optimal composite composition (PLA/0.1Clay) and the type of filler (Grid 90/85) were determined to ensure the best performance properties.The work focuses on PLA/Clay composites and dry friction conditions, which require further research for other fillers and operating environments. The results provide a basis for developing environmentally friendly wear-resistant materials with improved tribotechnical properties.The study demonstrates the potential of PLA composites for parts operating in friction pairs without lubrication, particularly in the automotive, medical and textile industries. The results contribute to the development of additive manufacturing for manufacturing wear-resistant parts with complex geometries.The article comprehensively analyses the influence of the composition of PLA composites with the addition of clay and the type of filling during 3D printing on tribological properties. The proposed combination of materials science and tribological methods for optimizing polymer properties significantly contributes to the development of environmentally friendly materials and 3D printing technologies.
- 1 January 2025
- Published by Index Copernicus in Journal of Achievements in Materials and Manufacturing Engineering
- Vol. 128 (1) , 5-17
Tribological properties of PLA-based composites produced by 3D printing
The current trends in the development of additive technologies, which are actively used in various industries, have been analysed. Special attention was found to be paid to polylactic acid (PLA), an environmentally friendly and biodegradable polymer widely used in 3D printing due to its low melting point and cost-effectiveness. The tribological properties of PLA were improved by adding clay in different concentrations and changing the filling type during printing. The highest indicators of wear resistance and the minimum coefficient of friction were found in the PLA/0.1Clay composite with Grid 90/85 filling. Such a type of filling provided optimal tribological properties for all composites due to the implementation of an abrasive wear mechanism accompanied by plastic deformation. It was revealed that the introduction of clay plasticized the material, which resulted in the widening of the sliding tracks.Pure PLA and PLA/Clay composites with different clay concentrations (0.1, 0.2, 0.3 g per 50 g PLA) were used for the study. The samples were printed with Sphere/100, Grid 90/100 and Grid 90/85 infill to study the effect of structure and density on tribological properties. Density, clay distribution (SEM), tribological tests, as well as wear track structure and friction mechanisms were investigated. The nature of clay distribution in the obtained filaments was evaluated by scanning electron microscopy (SEM) on a JSM-IT200 scanning electron microscope (Tokyo, Japan). To establish the elemental composition of the clay used to create the filaments, X-ray fluorescence analysis was performed on a CEP-01 Elvax Light X-ray spectrometer. The hardness of the samples was measured by indentation according to the Shore method on the Shore hardness tester HT-6510D. Tribological studies of the obtained samples were carried out according to the ball-on-disk scheme on the Tester T-01M computerized friction machine. The microstructure of the surfaces of the studied samples was analysed using an MBS-9 microscope.The influence of the chemical composition of PLA/Clay and the type of filler on the tribological characteristics, including wear resistance, wear intensity and friction mechanisms, was evaluated. The optimal composite composition (PLA/0.1Clay) and the type of filler (Grid 90/85) were determined to ensure the best performance properties.The work focuses on PLA/Clay composites and dry friction conditions, which require further research for other fillers and operating environments. The results provide a basis for developing environmentally friendly wear-resistant materials with improved tribotechnical properties.The study demonstrates the potential of PLA composites for parts operating in friction pairs without lubrication, particularly in the automotive, medical and textile industries. The results contribute to the development of additive manufacturing for manufacturing wear-resistant parts with complex geometries.The article comprehensively analyses the influence of the composition of PLA composites with the addition of clay and the type of filling during 3D printing on tribological properties. The proposed combination of materials science and tribological methods for optimizing polymer properties significantly contributes to the development of environmentally friendly materials and 3D printing technologies.
- 14 April 2023
- Published by Research and Innovation Centre Pro-Akademia in Acta Innovations
- No. 48,p. 22-37
A brief overview of the use of additive manufacturing of con-create materials in construction
Currently, additive technology is becoming increasingly popular in different areas, including its applications in construction industry. The main aim of the chapter is to show the selected applications of 3D printing technology in the construction industry and the usage of this technology on distinct stages of a construction project, from architectural design to performance of residential buildings and other civil engineering constructions. The chapter is based on a critical analysis of the literature sources, as well as the authors' experiences. The data collected are supported by selected case studies from five projects. The main findings show that 3D printing brings a lot of advantages in the construction industry, for instance: low labour costs, less waste, and high efficiency, but it still requires development and optimization.
- 14 April 2023
- Published by Research and Innovation Centre Pro-Akademia in Acta Innovations
- No. 48,p. 22-37
A brief overview of the use of additive manufacturing of con-create materials in construction
Currently, additive technology is becoming increasingly popular in different areas, including its applications in construction industry. The main aim of the chapter is to show the selected applications of 3D printing technology in the construction industry and the usage of this technology on distinct stages of a construction project, from architectural design to performance of residential buildings and other civil engineering constructions. The chapter is based on a critical analysis of the literature sources, as well as the authors' experiences. The data collected are supported by selected case studies from five projects. The main findings show that 3D printing brings a lot of advantages in the construction industry, for instance: low labour costs, less waste, and high efficiency, but it still requires development and optimization.
- Open Access
- 18 December 2021
- Published by Springer Nature in Journal of Polymers and the Environment
- Vol. 30 (6) , 2341-2354
Mechanical, Thermal and Microstructural Characteristic of 3D Printed Polylactide Composites with Natural Fibers: Wood, Bamboo and Cork
In the study, polylactide-based (PLA) composites modified with natural particles (wood, bamboo, and cork) and with different levels of infilling (100%, 80%, and 60%) obtained by fused deposition modeling were tested. The effect of fiber type, infill level and crystallization rate on the mechanical properties were investigated by using tensile, flexural, and impact tests. The materials were subjected to mechanical tests carried out at 23 and 80 °C. Differential scanning calorimetry were employed to analyze crystallization behavior of composite. Furthermore, hydrothermal degradation was performed, and its effect on the properties was analyzed. The addition of natural fillers and different levels of infilling result in a similar level of reduction in the properties. However, the addition of natural fillers resulted in a slightly lower drop than the lowered infilling rate − 40% and 50% for tensile strength, respectively. Moreover, it was found that, composites made of PLA are more sensitive to high temperatures than to water. The decrease in Young's modulus of PLA at 80 °C was 90%, while after 28 days of hydrodegradation ~ 9%. The addition of fibers reduced this decrease at elevated temperatures. Importantly, in the case of a brittle material such as PLA, the impact strength has been improved by 50% for composites with cork particles and other lignocellulosic composites remained at the same level as for resin. Generally, the thermal treatment of composites increased the degree of crystallinity of the materials, as reflected in the higher results of mechanical tests.
- 18 December 2021
- Published by Springer Nature in Journal of Polymers and the Environment
- Vol. 30 (6) , 2341-2354
Open AccessMechanical, Thermal and Microstructural Characteristic of 3D Printed Polylactide Composites with Natural Fibers: Wood, Bamboo and Cork
In the study, polylactide-based (PLA) composites modified with natural particles (wood, bamboo, and cork) and with different levels of infilling (100%, 80%, and 60%) obtained by fused deposition modeling were tested. The effect of fiber type, infill level and crystallization rate on the mechanical properties were investigated by using tensile, flexural, and impact tests. The materials were subjected to mechanical tests carried out at 23 and 80 °C. Differential scanning calorimetry were employed to analyze crystallization behavior of composite. Furthermore, hydrothermal degradation was performed, and its effect on the properties was analyzed. The addition of natural fillers and different levels of infilling result in a similar level of reduction in the properties. However, the addition of natural fillers resulted in a slightly lower drop than the lowered infilling rate − 40% and 50% for tensile strength, respectively. Moreover, it was found that, composites made of PLA are more sensitive to high temperatures than to water. The decrease in Young's modulus of PLA at 80 °C was 90%, while after 28 days of hydrodegradation ~ 9%. The addition of fibers reduced this decrease at elevated temperatures. Importantly, in the case of a brittle material such as PLA, the impact strength has been improved by 50% for composites with cork particles and other lignocellulosic composites remained at the same level as for resin. Generally, the thermal treatment of composites increased the degree of crystallinity of the materials, as reflected in the higher results of mechanical tests.