Ahmet Yönetken
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ahmet Yönetken has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Ayhan Erol
AFYON KOCATEPE ÜNİVERSİTESİ, TEKNOLOJİ FAKÜLTESİ, METALURJİ VE MALZEME MÜHENDİSLİĞİ BÖLÜMÜ
8 shared publications - Vildan Ozkan Bilici
Afyon Kocatepe University, Science And Literature Faculty, Physics Dept., 03200, Afyonkarahisar, Turkey
5 shared publications Ayhan Erol
Afyon Kocatepe University: Afyon Kocatepe Universitesi
4 shared publications- Günnur Peşmen
Afyon Kocatepe Universitesi
3 shared publications - Ayhan Erol
Afyon Kocatepe University
2 shared publications - İdRis Kosova
AFYON KOCATEPE UNIVERSITY, FACULTY OF TECHNOLOGY
2 shared publications
Latest Publications
- Open Access
- 16 June 2026
- Published by Osmaniye Korkut Ata Universitesi in Osmaniye Korkut Ata Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 9 (3) , 1572-1584
Effect of Layer Configuration and Particle Interlayers on the Mechanical Properties of Carbon Fiber/Epoxy Composites
This study investigates the development and characterization of carbon fiber-reinforced epoxy composites, with a focus on lightweight design optimization for drone body applications. Laminates with different fiber layer configurations were fabricated using the hand lay-up technique and tested in accordance with ISO 527-2 for tensile strength, ISO 180 for impact resistance, as well as mass and thickness measurements. The results indicate that varying the layer configuration has a significant effect on the balance between mechanical strength and weight reduction, which is critical for aerial vehicle performance. To enhance polymerization efficiency and improve the overall material properties, curing was carried out both at room temperature and under thermal conditions. The findings provide valuable insights into the design–performance relationship of carbon fiber/epoxy composites, highlighting their potential for advanced lightweight structural applications.
- 16 June 2026
- Published by Osmaniye Korkut Ata Universitesi in Osmaniye Korkut Ata Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 9 (3) , 1572-1584
Open AccessEffect of Layer Configuration and Particle Interlayers on the Mechanical Properties of Carbon Fiber/Epoxy Composites
This study investigates the development and characterization of carbon fiber-reinforced epoxy composites, with a focus on lightweight design optimization for drone body applications. Laminates with different fiber layer configurations were fabricated using the hand lay-up technique and tested in accordance with ISO 527-2 for tensile strength, ISO 180 for impact resistance, as well as mass and thickness measurements. The results indicate that varying the layer configuration has a significant effect on the balance between mechanical strength and weight reduction, which is critical for aerial vehicle performance. To enhance polymerization efficiency and improve the overall material properties, curing was carried out both at room temperature and under thermal conditions. The findings provide valuable insights into the design–performance relationship of carbon fiber/epoxy composites, highlighting their potential for advanced lightweight structural applications.
- Open Access
- 16 September 2025
- Published by Osmaniye Korkut Ata Universitesi in Osmaniye Korkut Ata Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 8 (4) , 1654-1669
Investigation of Energy Efficiency with Artificial Intelligence Based Dynamic Blade Angle Control for Wind Turbines
In this study, This study examines the use of Dynamic Blade Angle Control (DBAC) to improve energy efficiency in wind turbines. DBAC adapts blade pitch based on wind speed fluctuations to optimize energy production while maintaining turbine safety. Using an artificial intelligence-based model, this study analyzes the effects of DBAC on energy efficiency. The model predicts energy production based on wind speed and blade pitch, showing that DBAC increases energy efficiency at low speeds and ensures turbine safety at high speeds. The model's performance is enhanced with feedforward control strategies and LiDAR-assisted systems. These results emphasize the importance of DBAC and AI-based control systems in enhancing energy efficiency in wind turbines
- 16 September 2025
- Published by Osmaniye Korkut Ata Universitesi in Osmaniye Korkut Ata Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 8 (4) , 1654-1669
Open AccessInvestigation of Energy Efficiency with Artificial Intelligence Based Dynamic Blade Angle Control for Wind Turbines
In this study, This study examines the use of Dynamic Blade Angle Control (DBAC) to improve energy efficiency in wind turbines. DBAC adapts blade pitch based on wind speed fluctuations to optimize energy production while maintaining turbine safety. Using an artificial intelligence-based model, this study analyzes the effects of DBAC on energy efficiency. The model predicts energy production based on wind speed and blade pitch, showing that DBAC increases energy efficiency at low speeds and ensures turbine safety at high speeds. The model's performance is enhanced with feedforward control strategies and LiDAR-assisted systems. These results emphasize the importance of DBAC and AI-based control systems in enhancing energy efficiency in wind turbines
- Open Access
- 16 June 2025
- Published by Osmaniye Korkut Ata Universitesi in Osmaniye Korkut Ata Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 8 (3) , 1258-1277
Güneş Panellerinde Gölgelenme Durumunda Maksimum Güç Noktası ile Verim Arttırımı
Güneş enerjisi güneş panelleri yardımı ile insanlar tarafından kullanılabilir hale gelmektedir. Fakat enerji kullanılabilir hale gelirken güneşin tüm enerjisinden yarar sağlanamamaktadır. Kullanılacak enerjide kayıplar olmaktadır. Bunun sebeplerinden biri de güneş panellerinin gölgelenme durumundan kaynaklı düzgün ışınım alamamasından dolayı ürettiği güçte azalışa sebep olmasıdır. Gölgelenme, verimde azalmaya ve panellerin bozulmasına sebep olabilmektedir. Gölgelenme durumundan etkilenmemek için birçok yöntem bulunmaktadır. Bu yöntemlerden biri de Maksimum Güç Noktası Takibidir. Bu makalede, kısmi gölgelemenin güneş panellerinin performansını nasıl etkilediğini ve Maksimum Güç Noktası Takibi (MPPT) gibi azaltma tekniklerini incelemeyi amaçlamıştır. Bu çalışmada Matlab\ Simulink programı kullanılarak Maksimum Güç noktası Takibi teknikleri olan Bulanık Mantık kontrolü üzerinde çalışılmıştır. Çalışma iki adet güneş paneli dizisi, bulanık mantık ve Boost dönüştürücü kullanarak tasarlanmış ve MPPT kullanarak ve MPPT kullanmadan elde edilen güç, voltaj ve akım değerleri karşılaştırılmıştır. Çalışmanın sonucunda kısmi gölgeleme altında kalan güneş panellerinin MPPT kullanarak yapılan çalışmada güç, verim ve performansının MPPT kullanmadan yapılan çalışmaya göre daha iyi sonuçlar verdiği anlaşılmıştır. Zorlu şartlar altında güneş panellerinden daha fazla verim alabilmek için MPPT tekniklerinin kullanılabileceği çalışma sonucunda net bir şekilde anlaşılmıştır.
- 16 June 2025
- Published by Osmaniye Korkut Ata Universitesi in Osmaniye Korkut Ata Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 8 (3) , 1258-1277
Open AccessGüneş Panellerinde Gölgelenme Durumunda Maksimum Güç Noktası ile Verim Arttırımı
Güneş enerjisi güneş panelleri yardımı ile insanlar tarafından kullanılabilir hale gelmektedir. Fakat enerji kullanılabilir hale gelirken güneşin tüm enerjisinden yarar sağlanamamaktadır. Kullanılacak enerjide kayıplar olmaktadır. Bunun sebeplerinden biri de güneş panellerinin gölgelenme durumundan kaynaklı düzgün ışınım alamamasından dolayı ürettiği güçte azalışa sebep olmasıdır. Gölgelenme, verimde azalmaya ve panellerin bozulmasına sebep olabilmektedir. Gölgelenme durumundan etkilenmemek için birçok yöntem bulunmaktadır. Bu yöntemlerden biri de Maksimum Güç Noktası Takibidir. Bu makalede, kısmi gölgelemenin güneş panellerinin performansını nasıl etkilediğini ve Maksimum Güç Noktası Takibi (MPPT) gibi azaltma tekniklerini incelemeyi amaçlamıştır. Bu çalışmada Matlab\ Simulink programı kullanılarak Maksimum Güç noktası Takibi teknikleri olan Bulanık Mantık kontrolü üzerinde çalışılmıştır. Çalışma iki adet güneş paneli dizisi, bulanık mantık ve Boost dönüştürücü kullanarak tasarlanmış ve MPPT kullanarak ve MPPT kullanmadan elde edilen güç, voltaj ve akım değerleri karşılaştırılmıştır. Çalışmanın sonucunda kısmi gölgeleme altında kalan güneş panellerinin MPPT kullanarak yapılan çalışmada güç, verim ve performansının MPPT kullanmadan yapılan çalışmaya göre daha iyi sonuçlar verdiği anlaşılmıştır. Zorlu şartlar altında güneş panellerinden daha fazla verim alabilmek için MPPT tekniklerinin kullanılabileceği çalışma sonucunda net bir şekilde anlaşılmıştır.
- Open Access
- 1 January 2025
- Published by Afyon Kocatepe Universitesi Fen Ve Muhendislik Bilimleri Dergisi in Afyon Kocatepe University Journal of Sciences and Engineering
- Vol. 25 (4) , 969-983
Çatı Tipi Güneş Enerji Santrali Tasarımı, Ekonomik ve Çevresel Analizi: Hatay İli Örneği
Bu çalışma Hatay ilinin iklim şartları ve elektrik talepleri göz önünde bulundurularak çatı üstü güneş enerji santrali tasarımının ekonomik ve çevresel etkilerini değerlendirmeyi amaçlamaktadır. PVsyst programının 7.4 sürümü kullanılarak gerçekleştirilen simülasyonlarla, yatırım maliyeti, elektrik üretimi ve geri dönüş süresi gibi ekonomik unsurlar üzerinde odaklanılmıştır. Çevresel analizde ise güneş enerjisinin elektrik enerjisine dönüşümünün karbon emisyonu üzerindeki etkisi incelenmiştir. Tasarlanan sistemin ekonomik ömrü 25 yıl olarak varsayılmış ve simülasyon sonucunda yılda 352.043 kWh enerji üretimi, %81,20 performans oranı ve 4,2 yıl geri ödeme süresi elde edilmiştir. Sistemin ekonomik ömrü boyunca 3543,4 ton karbon emisyonunun önlenmesi ve ihtiyaç fazlası enerjinin şebekeye aktarılabilmesi de projenin çevresel ve ekonomik faydalarını ortaya koymaktadır. Ayrıca, bu çalışmanın sonuçları 2023 yılında gerçekleşen Kahramanmaraş depremleri sonrası yeniden yapılanma sürecinde olan bölgeler için güneş enerjisi projelerinin tasarımı ve uygulanmasında önemli bir rehber niteliği taşımakta olup yenilenebilir enerji kaynaklarının kullanımının Hatay örneğinde incelenmesinin, sürdürülebilir yeniden yapılanma için benzer analizlerin diğer bölgeler için de yapılmasına ve benzer sistemlerin uygulanmasına öncülük edebileceği değerlendirilmektedir.
- 1 January 2025
- Published by Afyon Kocatepe Universitesi Fen Ve Muhendislik Bilimleri Dergisi in Afyon Kocatepe University Journal of Sciences and Engineering
- Vol. 25 (4) , 969-983
Open AccessÇatı Tipi Güneş Enerji Santrali Tasarımı, Ekonomik ve Çevresel Analizi: Hatay İli Örneği
Bu çalışma Hatay ilinin iklim şartları ve elektrik talepleri göz önünde bulundurularak çatı üstü güneş enerji santrali tasarımının ekonomik ve çevresel etkilerini değerlendirmeyi amaçlamaktadır. PVsyst programının 7.4 sürümü kullanılarak gerçekleştirilen simülasyonlarla, yatırım maliyeti, elektrik üretimi ve geri dönüş süresi gibi ekonomik unsurlar üzerinde odaklanılmıştır. Çevresel analizde ise güneş enerjisinin elektrik enerjisine dönüşümünün karbon emisyonu üzerindeki etkisi incelenmiştir. Tasarlanan sistemin ekonomik ömrü 25 yıl olarak varsayılmış ve simülasyon sonucunda yılda 352.043 kWh enerji üretimi, %81,20 performans oranı ve 4,2 yıl geri ödeme süresi elde edilmiştir. Sistemin ekonomik ömrü boyunca 3543,4 ton karbon emisyonunun önlenmesi ve ihtiyaç fazlası enerjinin şebekeye aktarılabilmesi de projenin çevresel ve ekonomik faydalarını ortaya koymaktadır. Ayrıca, bu çalışmanın sonuçları 2023 yılında gerçekleşen Kahramanmaraş depremleri sonrası yeniden yapılanma sürecinde olan bölgeler için güneş enerjisi projelerinin tasarımı ve uygulanmasında önemli bir rehber niteliği taşımakta olup yenilenebilir enerji kaynaklarının kullanımının Hatay örneğinde incelenmesinin, sürdürülebilir yeniden yapılanma için benzer analizlerin diğer bölgeler için de yapılmasına ve benzer sistemlerin uygulanmasına öncülük edebileceği değerlendirilmektedir.
- 16 December 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 69 (4) , 1313-1321
Evaluating of the Relationships between aAverage Particle Size and Microstructure-Mechanical Properties of Materials Produced in Different Compositions using Ultrasonic Method
Pulse-echo ultrasonic test, which is one of the non-destructive testing methods, was used to measure ultrasonic quantities such as longitudinal velocity (VL), shear velocity (VT) and attenuation coefficient (α) in FeCrMn composites. The corresponding elastic constants were determined depending on the longitudinal and transverse velocity. The aim was to reveal the correlation between the microstructural and mechanical properties of FeCrMn composites and ultrasonic quantities. The effect of adding Cr particles on VL and VT velocities is obviously attributed to the change in elastic and shear modulus of FeCrMn composites. It was found that both VL and VT velocities, Young’s modulus (E) and shear modulus (G), as well as hardness values, changed approximately linearly with increasing Cr content. In this study, samples with different volumetric compositions were produced using the powder metallurgy method. It has been revealed that both the applied method and the increase in the amount of Cr have a significant effect on the velocities of VL and VT. The increase in VL and VT is due to the increase of Cr particles, the homogeneous distribution of Cr, the formation of samples especially at a certain temperature, and the decrease of porosity. As a result of these, a decrease in attenuation values was observed depending on the mean grain size. Elastic constants were found to vary in the same way as ultrasonic velocities. By increasing the Cr content both the hardness values and the shear modulus were improved and a good correlation was observed with the grain size.
- 16 December 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 69 (4) , 1313-1321
Evaluating of the Relationships between aAverage Particle Size and Microstructure-Mechanical Properties of Materials Produced in Different Compositions using Ultrasonic Method
Pulse-echo ultrasonic test, which is one of the non-destructive testing methods, was used to measure ultrasonic quantities such as longitudinal velocity (VL), shear velocity (VT) and attenuation coefficient (α) in FeCrMn composites. The corresponding elastic constants were determined depending on the longitudinal and transverse velocity. The aim was to reveal the correlation between the microstructural and mechanical properties of FeCrMn composites and ultrasonic quantities. The effect of adding Cr particles on VL and VT velocities is obviously attributed to the change in elastic and shear modulus of FeCrMn composites. It was found that both VL and VT velocities, Young’s modulus (E) and shear modulus (G), as well as hardness values, changed approximately linearly with increasing Cr content. In this study, samples with different volumetric compositions were produced using the powder metallurgy method. It has been revealed that both the applied method and the increase in the amount of Cr have a significant effect on the velocities of VL and VT. The increase in VL and VT is due to the increase of Cr particles, the homogeneous distribution of Cr, the formation of samples especially at a certain temperature, and the decrease of porosity. As a result of these, a decrease in attenuation values was observed depending on the mean grain size. Elastic constants were found to vary in the same way as ultrasonic velocities. By increasing the Cr content both the hardness values and the shear modulus were improved and a good correlation was observed with the grain size.
- 16 December 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 69 (4) , 1367-1373
Use of Ultrasound to Identify Microstructure-Property Relationships in (AlN + WC) Fabricated with Electroless Ni Producing
In order to improve the properties of the materials produced by the powder metallurgy method, first of all, powders (16.59% AlN + 6.63% WC) were coated with nickel (Ni) by electroless method, and then box boriding, which is one of the most widely used surface coating methods, was applied. A composite formed with (16.59% AlN + 6.63% WC)76.7Ni was prepared under the Ar shroud in the temperature range of 1000-1400°C. Pulse-echo technique was used for ultrasonic velocity measurements on Ni coated (16.59% AlN + 6.63% WC) samples. It is aimed to examine the change of physical, mechanical and ultrasonic properties of the obtained ceramic-metal composites depending on different sintering temperatures. In addition, the samples were characterized by mechanical and metallographic examination. The results show that the longitudinal and transverse ultrasonic velocity values and ultrasonic modulus (shear, bulk, Young’s etc.) values increase simultaneously with the increase of sintering temperature. The highest microhardness value was observed in composite samples sintered at 1400°C and its value was 1150.80 Hv. The increased strength is mainly due to grain refinement and strong interfacial bonding between Ni particles and AlN and WC matrix.
- 16 December 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 69 (4) , 1367-1373
Use of Ultrasound to Identify Microstructure-Property Relationships in (AlN + WC) Fabricated with Electroless Ni Producing
In order to improve the properties of the materials produced by the powder metallurgy method, first of all, powders (16.59% AlN + 6.63% WC) were coated with nickel (Ni) by electroless method, and then box boriding, which is one of the most widely used surface coating methods, was applied. A composite formed with (16.59% AlN + 6.63% WC)76.7Ni was prepared under the Ar shroud in the temperature range of 1000-1400°C. Pulse-echo technique was used for ultrasonic velocity measurements on Ni coated (16.59% AlN + 6.63% WC) samples. It is aimed to examine the change of physical, mechanical and ultrasonic properties of the obtained ceramic-metal composites depending on different sintering temperatures. In addition, the samples were characterized by mechanical and metallographic examination. The results show that the longitudinal and transverse ultrasonic velocity values and ultrasonic modulus (shear, bulk, Young’s etc.) values increase simultaneously with the increase of sintering temperature. The highest microhardness value was observed in composite samples sintered at 1400°C and its value was 1150.80 Hv. The increased strength is mainly due to grain refinement and strong interfacial bonding between Ni particles and AlN and WC matrix.
- Open Access
- 23 October 2024
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 12 (4) , 2076-2090
Prediction Of Brushless DC Motor And Propeller Efficiency Using An Artificial Neural Network Model
This study focuses on an artificial neural network model that allows users of brushless motor and propeller test rigs to compare the accuracy of data received in the interface software during testing. Brushless motors are widely used in modern aviation and industrial applications. Therefore, it is essential to analyze the factors affecting motor efficiency and accurately predict this data. This study involves the creation of an artificial neural network model from data to predict the percentage of motor efficiency for the brushless motors and propellers used in the test, whose length is measured in inches. Within the scope of this research, a useful tool is provided for users to flexibly test motor and propeller configurations and accurately analyze test results. The developed artificial neural network model has the ability to make reliable and accurate predictions for various motor-propeller configurations. Furthermore, the model is easy to use and offers expandable features. This study aims to create a valuable reference source for users of brushless motor and propeller test rigs to effectively analyze test data.
- 23 October 2024
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 12 (4) , 2076-2090
Open AccessPrediction Of Brushless DC Motor And Propeller Efficiency Using An Artificial Neural Network Model
This study focuses on an artificial neural network model that allows users of brushless motor and propeller test rigs to compare the accuracy of data received in the interface software during testing. Brushless motors are widely used in modern aviation and industrial applications. Therefore, it is essential to analyze the factors affecting motor efficiency and accurately predict this data. This study involves the creation of an artificial neural network model from data to predict the percentage of motor efficiency for the brushless motors and propellers used in the test, whose length is measured in inches. Within the scope of this research, a useful tool is provided for users to flexibly test motor and propeller configurations and accurately analyze test results. The developed artificial neural network model has the ability to make reliable and accurate predictions for various motor-propeller configurations. Furthermore, the model is easy to use and offers expandable features. This study aims to create a valuable reference source for users of brushless motor and propeller test rigs to effectively analyze test data.
- Open Access
- 2 October 2024
- Published by Iskender AKKURT in International Journal of Computational and Experimental Science and Engineering
- Vol. 10 (4)
Characterization of Microstructure of Fe-TiC and Fe-B4C Composites Using Ultrasonic Measurements
In this paper, an iron (Fe) matrix reinforced with boron carbide (B4C) and titanium carbide (TiC) was produced by conventional furnace sintering at the same compositions and temperatures. Experimental data on the change in ultrasonic velocity parameter, densities and porosity of these two different microstructure composites during microstructure development are reported. The microstructural phases were characterized by metallographic studies and hardness measurements. The velocities of ultrasonic longitudinal waves were measured by the pulse- echo method using the transmit/receive probe. In the Fe-TiC composite sample, ultrasound longitudinal wave velocity, hardness and porosity increased linearly depending on the increasing amount of TiC. In the Fe-B4C composite sample, on the other hand, there is a linear increase in general depending on the increasing amount of B4C, and there is a sharp decrease in the amount of 8,33% B4C. The reason for this decrease and other results are explained by taking into account SEM and XRD analyzes.
- 2 October 2024
- Published by Iskender AKKURT in International Journal of Computational and Experimental Science and Engineering
- Vol. 10 (4)
Open AccessCharacterization of Microstructure of Fe-TiC and Fe-B4C Composites Using Ultrasonic Measurements
In this paper, an iron (Fe) matrix reinforced with boron carbide (B4C) and titanium carbide (TiC) was produced by conventional furnace sintering at the same compositions and temperatures. Experimental data on the change in ultrasonic velocity parameter, densities and porosity of these two different microstructure composites during microstructure development are reported. The microstructural phases were characterized by metallographic studies and hardness measurements. The velocities of ultrasonic longitudinal waves were measured by the pulse- echo method using the transmit/receive probe. In the Fe-TiC composite sample, ultrasound longitudinal wave velocity, hardness and porosity increased linearly depending on the increasing amount of TiC. In the Fe-B4C composite sample, on the other hand, there is a linear increase in general depending on the increasing amount of B4C, and there is a sharp decrease in the amount of 8,33% B4C. The reason for this decrease and other results are explained by taking into account SEM and XRD analyzes.
- Open Access
- 16 September 2024
- Published by Osmaniye Korkut Ata Universitesi in Osmaniye Korkut Ata Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 7 (4) , 1579-1599
The Effect of Gas Turbine Inlet Air Temperature On Electricity Production Effiency in Trigeneration Power Plants
In this study, the operation of gas turbines used to generate energy in trigeneration plants with turbine inlet air at various temperatures was investigated. In today's world, the importance of energy and its efficient use is increasing. Developing population and technologies have increased the energy we need, and thus energy costs have reached serious levels. All these reveal the necessity of using energy efficiently. Trigeneration power plants provide less fossil fuel consumption than conventional production because they have high efficiency, prevent line losses with on-site electricity generation, and provide combined energy production. In our study, the increase in electricity production efficiency by cooling the inlet air of the Solar Turbines Taurus 60 gas turbine used in the trigeneration power plant was examined. It was determined that there was a 30.08% increase in active power efficiency in electricity production by cooling the turbine inlet air from 41.2 °C to 9.1 °C.
- 16 September 2024
- Published by Osmaniye Korkut Ata Universitesi in Osmaniye Korkut Ata Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 7 (4) , 1579-1599
Open AccessThe Effect of Gas Turbine Inlet Air Temperature On Electricity Production Effiency in Trigeneration Power Plants
In this study, the operation of gas turbines used to generate energy in trigeneration plants with turbine inlet air at various temperatures was investigated. In today's world, the importance of energy and its efficient use is increasing. Developing population and technologies have increased the energy we need, and thus energy costs have reached serious levels. All these reveal the necessity of using energy efficiently. Trigeneration power plants provide less fossil fuel consumption than conventional production because they have high efficiency, prevent line losses with on-site electricity generation, and provide combined energy production. In our study, the increase in electricity production efficiency by cooling the inlet air of the Solar Turbines Taurus 60 gas turbine used in the trigeneration power plant was examined. It was determined that there was a 30.08% increase in active power efficiency in electricity production by cooling the turbine inlet air from 41.2 °C to 9.1 °C.
- 1 October 2022
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 25 (3) , 1031-1039
Investigation of Diffusion Welding Capability of WC Ceramic Based Ni Doped Composites
In this study, sample pairs of (WC) Ni / (WC) Ni and WC-Ni / WC-Ni formed from (WC) Ni composites produced from Ni coated WC powders and uncoated WC-Ni / powders were used for diffusion welding. Diffusion welding was carried out by preloaded compression system under Ar atmosphere. Diffusion welding was obtained by changing bonding pressure and temperature. Schimadzu 100kN universal tensile machine was employed for tensile shear testing of diffusion welded couples. The tensile shear test results showed that electroless nickel coated WC(Ni) composite diffusion couples yielded best tensile shear load bearing capacity 35,4 MPa compared to other diffusion couples. Hardness values ranging from 200 to 400HV were determined. SEM and XRD analysis systems were used to analyze the microstructural analysis of the composites and diffusion welded samples obtained in the study and to analyze the particles formed at the weld interface.
- 1 October 2022
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 25 (3) , 1031-1039
Investigation of Diffusion Welding Capability of WC Ceramic Based Ni Doped Composites
In this study, sample pairs of (WC) Ni / (WC) Ni and WC-Ni / WC-Ni formed from (WC) Ni composites produced from Ni coated WC powders and uncoated WC-Ni / powders were used for diffusion welding. Diffusion welding was carried out by preloaded compression system under Ar atmosphere. Diffusion welding was obtained by changing bonding pressure and temperature. Schimadzu 100kN universal tensile machine was employed for tensile shear testing of diffusion welded couples. The tensile shear test results showed that electroless nickel coated WC(Ni) composite diffusion couples yielded best tensile shear load bearing capacity 35,4 MPa compared to other diffusion couples. Hardness values ranging from 200 to 400HV were determined. SEM and XRD analysis systems were used to analyze the microstructural analysis of the composites and diffusion welded samples obtained in the study and to analyze the particles formed at the weld interface.