Adela Roubickova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Adela Roubickova has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Antonin Tichy
Clinic for Conservative Dentistry, Periodontology and Digital Dentistry LMU University Hospital Munich Germany
2 shared publications - Marketa Simkova
Department of Steroids and Proteofactors, Institute of Endocrinology, Narodni 8, 116 94 Prague, Czech Republic
1 shared publication - Michaela Duskova
Department of Steroids and Proteofactors, Institute of Endocrinology, Narodni 8, 116 94 Prague, Czech Republic
1 shared publication - Pavel Bradna
Institute of Dental Medicine, First Faculty of Medicine of the Charles University and General University Hospital in Prague, Karlovo namesti 32, Prague, 121 11, Czech Republic
1 shared publication - Pavel Bradna
Institute of Dental Medicine, First Faculty of Medicine, Charles University, General University Hospital, Karlovo Namesti 32, 121 11 Prague, Czech Republic
1 shared publication R. Vrbova
Institute of Dental Medicine, First Faculty of Medicine of the Charles University and General University Hospital in Prague, Karlovo namesti 32, Prague, 121 11, Czech Republic
1 shared publication
Latest Publications
- 19 November 2024
- Published by Elsevier in Journal of the Mechanical Behavior of Biomedical Materials
- Vol. 162, 106823
Indentation size effect in Knoop and Vickers hardness measurement of dental resin-based composites
- 19 November 2024
- Published by Elsevier in Journal of the Mechanical Behavior of Biomedical Materials
- Vol. 162, 106823
Indentation size effect in Knoop and Vickers hardness measurement of dental resin-based composites
- Open Access
Bisphenol A Release from Dental Composites and Resin-Modified Glass Ionomers under Two Polymerization Conditions
Bisphenol A (BPA)-based monomers are commonly contained in dental resin-based materials. As BPA is an endocrine disruptor, its long-term release from restorative composites and resin-modified glass ionomers (RM-GICs) under two polymerization conditions was measured in this study. Specimens of two conventional composites containing BPA-based monomers, two “BPA-free” composites, and two RM-GICs were polymerized from one side for 20 s at 1300 mW/cm2 or for 5 s at 3000 mW/cm2. The amounts of BPA released in artificial saliva and methanol after 1, 4, 9, 16, 35, 65, 130, and 260 days were measured using liquid chromatography–tandem mass spectrometry. The highest amounts of BPA were released from conventional composites, followed by RM-GICs, while the least was released from “BPA-free” composites. Amounts of released BPA were significantly higher in methanol and decreased gradually after the first day. Fast polymerization (5 s at 3000 mW/cm2) resulted in a significantly higher release of BPA after 1 day, but the effect of polymerization conditions was not significant overall. In conclusion, fast polymerization increased the initial release of BPA, but the released amounts were significantly lower than the current tolerable daily intake (4 μg/kg body weight/day) even in methanol, representing the worst-case scenario of BPA release.
Open AccessBisphenol A Release from Dental Composites and Resin-Modified Glass Ionomers under Two Polymerization Conditions
Bisphenol A (BPA)-based monomers are commonly contained in dental resin-based materials. As BPA is an endocrine disruptor, its long-term release from restorative composites and resin-modified glass ionomers (RM-GICs) under two polymerization conditions was measured in this study. Specimens of two conventional composites containing BPA-based monomers, two “BPA-free” composites, and two RM-GICs were polymerized from one side for 20 s at 1300 mW/cm2 or for 5 s at 3000 mW/cm2. The amounts of BPA released in artificial saliva and methanol after 1, 4, 9, 16, 35, 65, 130, and 260 days were measured using liquid chromatography–tandem mass spectrometry. The highest amounts of BPA were released from conventional composites, followed by RM-GICs, while the least was released from “BPA-free” composites. Amounts of released BPA were significantly higher in methanol and decreased gradually after the first day. Fast polymerization (5 s at 3000 mW/cm2) resulted in a significantly higher release of BPA after 1 day, but the effect of polymerization conditions was not significant overall. In conclusion, fast polymerization increased the initial release of BPA, but the released amounts were significantly lower than the current tolerable daily intake (4 μg/kg body weight/day) even in methanol, representing the worst-case scenario of BPA release.