Hadi Parvizi
Hadi Parvizi has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Amir Farasat
1 shared publicationHamed Aghaei
1 shared publicationHassan Bahrami
Schlumberger
1 shared publication- Jamal Siavoshi
Husky Energy
1 shared publication Mohammad Azad
1 shared publicationMohammad Hussein Karimi
Pars Oil and Gas Company
1 shared publication
Latest Publications
- Open Access
- 1 December 2022
- Published by Elsevier in Petroleum Research
- Vol. 7 (4) , 419-429
Case study of hydraulic fracturing in an offshore carbonate oil reservoir
- 1 December 2022
- Published by Elsevier in Petroleum Research
- Vol. 7 (4) , 419-429
Open AccessCase study of hydraulic fracturing in an offshore carbonate oil reservoir
- Open Access
Wearable Sensors for Learning Enhancement in Higher Education
Wearable sensors have traditionally been used to measure and monitor vital human signs for well-being and healthcare applications. However, there is a growing interest in using and deploying these technologies to facilitate teaching and learning, particularly in a higher education environment. The aim of this paper is therefore to systematically review the range of wearable devices that have been used for enhancing the teaching and delivery of engineering curricula in higher education. Moreover, we compare the advantages and disadvantages of these devices according to the location in which they are worn on the human body. According to our survey, wearable devices for enhanced learning have mainly been worn on the head (e.g., eyeglasses), wrist (e.g., watches) and chest (e.g., electrocardiogram patch). In fact, among those locations, head-worn devices enable better student engagement with the learning materials, improved student attention as well as higher spatial and visual awareness. We identify the research questions and discuss the research inclusion and exclusion criteria to present the challenges faced by researchers in implementing learning technologies for enhanced engineering education. Furthermore, we provide recommendations on using wearable devices to improve the teaching and learning of engineering courses in higher education.
Open AccessWearable Sensors for Learning Enhancement in Higher Education
Wearable sensors have traditionally been used to measure and monitor vital human signs for well-being and healthcare applications. However, there is a growing interest in using and deploying these technologies to facilitate teaching and learning, particularly in a higher education environment. The aim of this paper is therefore to systematically review the range of wearable devices that have been used for enhancing the teaching and delivery of engineering curricula in higher education. Moreover, we compare the advantages and disadvantages of these devices according to the location in which they are worn on the human body. According to our survey, wearable devices for enhanced learning have mainly been worn on the head (e.g., eyeglasses), wrist (e.g., watches) and chest (e.g., electrocardiogram patch). In fact, among those locations, head-worn devices enable better student engagement with the learning materials, improved student attention as well as higher spatial and visual awareness. We identify the research questions and discuss the research inclusion and exclusion criteria to present the challenges faced by researchers in implementing learning technologies for enhanced engineering education. Furthermore, we provide recommendations on using wearable devices to improve the teaching and learning of engineering courses in higher education.
- 3 December 2008
- Published by Society of Petroleum Engineers (SPE)
Characterization of Fracture Dynamic Parameters to Simulate Naturally Fractured Reservoirs
Fractures identification is essential during exploration, drilling and well completion of naturally fractured reservoirs since they have a significant impact on flow contribution. There are different methods to characterize these systems based on formation properties and fluid flow behaviour such as logging and testing. Pressure-transient testing has long been recognized as a reservoir characterization tool. Although welltest analysis is a recommended technique for fracture evaluation, but its use is still not well understood. Analysis of pressure transient data provides dynamic reservoir properties such as average permeability, fracture storativity and fracture conductivity. An infusion of geological knowledge helps reducing uncertainty associated with any well-test interpretation. The static properties of naturally fractured reservoirs such as fracture aperture, fracture spacing and fracture porosity can be obtained from processing of Image Log data. Simulation of naturally fractured reservoirs needs defining fracture permeability, shape factor and fracture porosity in the fracture model. However, in most simulation studies, due to high uncertainties in estimating fracture permeability and shape factor values, these parameters are initially assumed in the model and they are usually tuned during history matching which can be time consuming and also affect other history match parameters. Reservoir simulation results and predictions might be inaccurate if the values of fracture properties in the model are not reliable. This paper shows using image log data associated with welltest analysis in order to determine dynamic fracture parameters such as fracture permeability and shape factor for reservoir simulation. In this study, sensitivity analysis has also been performed on fracture permeability, fracture porosity and shape factor in a real simulation model to show importance of accurate determination of fracture parameters. Introduction: Naturally fractured reservoirs differ from homogeneous reservoirs from many points of view: geological, petrophysical, production and economics. We may think of fractured reservoirs as initially homogeneous systems whose physical properties have been deformed or altered during their deposition. As a consequence, it is not always easy to match the behavior of these systems, specifically to forecast their production during simulation.
- 3 December 2008
- Published by Society of Petroleum Engineers (SPE)
Characterization of Fracture Dynamic Parameters to Simulate Naturally Fractured Reservoirs
Fractures identification is essential during exploration, drilling and well completion of naturally fractured reservoirs since they have a significant impact on flow contribution. There are different methods to characterize these systems based on formation properties and fluid flow behaviour such as logging and testing. Pressure-transient testing has long been recognized as a reservoir characterization tool. Although welltest analysis is a recommended technique for fracture evaluation, but its use is still not well understood. Analysis of pressure transient data provides dynamic reservoir properties such as average permeability, fracture storativity and fracture conductivity. An infusion of geological knowledge helps reducing uncertainty associated with any well-test interpretation. The static properties of naturally fractured reservoirs such as fracture aperture, fracture spacing and fracture porosity can be obtained from processing of Image Log data. Simulation of naturally fractured reservoirs needs defining fracture permeability, shape factor and fracture porosity in the fracture model. However, in most simulation studies, due to high uncertainties in estimating fracture permeability and shape factor values, these parameters are initially assumed in the model and they are usually tuned during history matching which can be time consuming and also affect other history match parameters. Reservoir simulation results and predictions might be inaccurate if the values of fracture properties in the model are not reliable. This paper shows using image log data associated with welltest analysis in order to determine dynamic fracture parameters such as fracture permeability and shape factor for reservoir simulation. In this study, sensitivity analysis has also been performed on fracture permeability, fracture porosity and shape factor in a real simulation model to show importance of accurate determination of fracture parameters. Introduction: Naturally fractured reservoirs differ from homogeneous reservoirs from many points of view: geological, petrophysical, production and economics. We may think of fractured reservoirs as initially homogeneous systems whose physical properties have been deformed or altered during their deposition. As a consequence, it is not always easy to match the behavior of these systems, specifically to forecast their production during simulation.