Tyler Williams
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Tyler Williams has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Devin Rappleye
Brigham Young University
4 shared publications Rankin Shum
Department of Chemical Engineering, Brigham Young University, Provo, Utah 84602, United States of America
2 shared publicationsRanon Fuller
Brigham Young University
2 shared publicationsCameron Vann
Brigham Young Univ, Dept Chem Engn, Provo, UT 84602 USA
1 shared publicationDevin Rappleye
Brigham Young University
1 shared publicationGreg Chipman
Brigham Young University
1 shared publication
Latest Publications
- 2 September 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (9) , 093508
Electrochemical Investigation of Moisture Byproducts in Molten Calcium Chloride
Residual water in molten CaCl2 reacts to form different byproducts, such as HCl, which can impact the corrosivity of the salt and efficiency of electrochemical operations, such as electrolytic oxide reduction and electrorefining. The ability to detect and quantify these byproducts electrochemically can provide feedback on the efficacy of vacuum drying and other purification methods, as well as the impact of these byproducts on process operations. An electrochemical signal’s association with the production of H2 is verified and characterized using cyclic voltammetry (CV) and residual gas analysis. CV estimated a 2-electron exchange process associated with H2 production. CV detected trace quantities of an oxidized species containing hydrogen in the salt on the order of 10 ppm. Different salt handling methods were compared for their impact on the hydrogen electrochemical signal. It was found that 30 min of exposure of CaCl2 in a beaker to low-humidity air (2 production signal.
- 2 September 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (9) , 093508
Electrochemical Investigation of Moisture Byproducts in Molten Calcium Chloride
Residual water in molten CaCl2 reacts to form different byproducts, such as HCl, which can impact the corrosivity of the salt and efficiency of electrochemical operations, such as electrolytic oxide reduction and electrorefining. The ability to detect and quantify these byproducts electrochemically can provide feedback on the efficacy of vacuum drying and other purification methods, as well as the impact of these byproducts on process operations. An electrochemical signal’s association with the production of H2 is verified and characterized using cyclic voltammetry (CV) and residual gas analysis. CV estimated a 2-electron exchange process associated with H2 production. CV detected trace quantities of an oxidized species containing hydrogen in the salt on the order of 10 ppm. Different salt handling methods were compared for their impact on the hydrogen electrochemical signal. It was found that 30 min of exposure of CaCl2 in a beaker to low-humidity air (2 production signal.
- 12 June 2024
- Published by Taylor & Francis in Nuclear Technology
- Vol. 211 (4) , 708-724
Electrochemical Identification of Metal Chlorides in Eutectic LiCl-KCl Without Prior Knowledge of Analyte Identities
- 12 June 2024
- Published by Taylor & Francis in Nuclear Technology
- Vol. 211 (4) , 708-724
Electrochemical Identification of Metal Chlorides in Eutectic LiCl-KCl Without Prior Knowledge of Analyte Identities
- 28 February 2024
- Published by Taylor & Francis in Nuclear Technology
- Vol. 210 (8) , 1464-1474
In Situ Chlorine Generation and Rare Earth Chlorination by Molten Salt Electrolysis
- 28 February 2024
- Published by Taylor & Francis in Nuclear Technology
- Vol. 210 (8) , 1464-1474
In Situ Chlorine Generation and Rare Earth Chlorination by Molten Salt Electrolysis
- Open Access
- 1 April 2023
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 170 (4) , 042502
Semi-Differentiation of Reversible, Soluble-Insoluble Potential Sweep Voltammograms
Semi-differentiation, or convolution as it is sometimes known, is a mathematical technique commonly used to disentangle overlapping peaks in cyclic or linear sweep voltammograms. However, this technique is often misapplied due to misunderstandings of fractional calculus. Additionally, rigorous treatment and validation of the theory of semi-differential analysis of reversible, soluble-insoluble electrochemical reactions is lacking. Peculiarities of semi-differentiation are explored; theoretical relations for semi-differentiated voltammograms are given; the exponential nature of the theoretical curve is explored; theoretical relations are compared to experimental voltammograms for AgNO3 in 1 M nitric acid at 298 K, NiCl2 in LiCl at 974 K, and LaCl3 in LiCl at 971 K; and the diffusion coefficients calculated from theoretical relations developed in this paper are shown to agree with those calculated using the Berzins-Delahay equation.
- 1 April 2023
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 170 (4) , 042502
Open AccessSemi-Differentiation of Reversible, Soluble-Insoluble Potential Sweep Voltammograms
Semi-differentiation, or convolution as it is sometimes known, is a mathematical technique commonly used to disentangle overlapping peaks in cyclic or linear sweep voltammograms. However, this technique is often misapplied due to misunderstandings of fractional calculus. Additionally, rigorous treatment and validation of the theory of semi-differential analysis of reversible, soluble-insoluble electrochemical reactions is lacking. Peculiarities of semi-differentiation are explored; theoretical relations for semi-differentiated voltammograms are given; the exponential nature of the theoretical curve is explored; theoretical relations are compared to experimental voltammograms for AgNO3 in 1 M nitric acid at 298 K, NiCl2 in LiCl at 974 K, and LaCl3 in LiCl at 971 K; and the diffusion coefficients calculated from theoretical relations developed in this paper are shown to agree with those calculated using the Berzins-Delahay equation.
- Open Access
- 1 December 2021
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 168 (12) , 123510
Review—Concentration Measurements In Molten Chloride Salts Using Electrochemical Methods
The electrochemical measurement of concentration in molten chloride salts is a valuable tool for the control of existing and potential industrial processes, recycling of precious materials and energy production. The electrochemical techniques commonly used to measure concentration and each techniques’ associated theory are discussed. Practices which improve measurement accuracy and precision are set forth. Exceptionally accurate and precise measurements published in the literature are evaluated based on their performance in specified concentration ranges. The strengths and weaknesses of the most accurate measurements are briefly explored. Chronopotentiometry (CP) and square wave voltammetry (SWV) are accurate and precise with low concentration measurements. SWV was accurate at low concentrations, even in multi-analyte mixtures. CP was accurate for only single analyte mixtures. Open-circuit potentiometry (OCP) is accurate and precise in single-analyte mixtures but yields large errors in multianalyte mixtures. Cyclic voltammetry (CV), chronoamperometry (CA) and normal pulse voltammetry (NPV) are accurate and precise across all concentration ranges. NPV is exceptionally well suited for measurements in melts with multiple electroactive species.
- 1 December 2021
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 168 (12) , 123510
Open AccessReview—Concentration Measurements In Molten Chloride Salts Using Electrochemical Methods
The electrochemical measurement of concentration in molten chloride salts is a valuable tool for the control of existing and potential industrial processes, recycling of precious materials and energy production. The electrochemical techniques commonly used to measure concentration and each techniques’ associated theory are discussed. Practices which improve measurement accuracy and precision are set forth. Exceptionally accurate and precise measurements published in the literature are evaluated based on their performance in specified concentration ranges. The strengths and weaknesses of the most accurate measurements are briefly explored. Chronopotentiometry (CP) and square wave voltammetry (SWV) are accurate and precise with low concentration measurements. SWV was accurate at low concentrations, even in multi-analyte mixtures. CP was accurate for only single analyte mixtures. Open-circuit potentiometry (OCP) is accurate and precise in single-analyte mixtures but yields large errors in multianalyte mixtures. Cyclic voltammetry (CV), chronoamperometry (CA) and normal pulse voltammetry (NPV) are accurate and precise across all concentration ranges. NPV is exceptionally well suited for measurements in melts with multiple electroactive species.