DBDean Bernečić

Dean Bernečić

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Dean Bernečić has a total of 8 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Marine Coolant Fluids’ Effect on the Mechanical Properties of Glass Fiber-Reinforced Composites

    by Dean Bernečić, Marino Mikelić, Goran Vizentin

    This study examines the effect of coolant and antifreeze solutions such as distilled water, ethylene glycol-based antifreeze with organic acid technology (OAT), and ethylene glycol-based antifreeze with inorganic inhibitors and glycerol (IAT/HOAT) on the tensile strength of glass fiber-reinforced polyester (GFRP-P) and vinyl ester (GFRP-VE) composites. Standardized specimens were produced and immersed in these solutions for three months at room temperature. Following exposure, tensile tests were conducted using the universal testing machine, supported by microscopic analysis to evaluate surface damage and internal structural changes such as composite layer delamination. The tensile test results show the highest decrease in tensile strength for GFRP-P specimens immersed in HOAT antifreeze (16.3%), whereas GFRP-VE specimens exhibit only a minimal reduction (3.4%). This difference is attributed to the higher chemical aggressiveness and alkalinity of the HOAT antifreeze. Furthermore, the decrease in the tensile strength of GFR-P exposed to OAT antifreeze is 6.1%, whereas GFRP-VE demonstrates a significantly smaller reduction of 1%, which can be attributed to the less aggressive chemical composition of the OAT formulation compared to HOAT. In contrast, the influence of distilled water on GFRP-P specimens is manifested as a tensile strength decrease of 12.7%, whereas GFRP-VE specimens show a reduction of 11%, attributed to the fluid’s density and the rate of hydrolytic degradation. These results contribute to a deeper understanding of the effects of various coolant media on the performance of GFRP in marine cooling systems, highlighting GFRP-VE as a more suitable matrix for prolonged exposure to coolant environments.

  • Open Access

    Application of VR Technology for Maritime Firefighting and Evacuation Training—A Review

    by Goran Vukelic, Dario Ogrizovic, Dean Bernecic, Darko Glujic, Goran Vizentin

    Firefighting and evacuation training are important tasks in maritime education and training, especially for crews working on large passenger ships, to ensure the safety of the vessel, cargo and passengers. With the evolution of virtual reality (VR) technology and the introduction of wearable hardware, a change in paradigm has happened in firefighting and evacuation training where these new technologies are being introduced. This paper serves as a review on the use of VR technology in maritime firefighting and evacuation training, trying to answer the following questions: what is the current state of using VR technology, and what are the research gaps that need to be addressed to further accelerate the implementation of VR? Research shows that other industries have adopted the use of VR technology relatively quickly, but the maritime industry still seems reluctant. As for the research gaps, the physics-based modelling of fire spread is discussed along with two other topics: the lack of immersive solutions for evacuation and the potential for developing search and rescue scenarios onboard a ship.


  • The influence of SCR on main engine parameters

    by Filip Rumac, Darko Glujić, Dean Bernečić

    Air pollution from ships is increasing due to higher global demand of goods, and with them, global emission standards as well. These standards are prescribed by MARPOL Annex VI and the introduction of emission control areas (ECA). Ships built before 1990. do not have to comply with these rules, but ships built after the early 2000. must follow "NOx Emission Tier I", which allows 17g/kWh NOx (for the slow speed diesel engines with <130 rpm), and selective catalytic reactors (SCR) are not necessary. Tier III NOx Emission standard was enforced in 2016 and it requires an 80% reduction in NOx emission compared to the Tier I, specifically 3.4 g/kWh, which can not be achieved without SCR or without using some other types of fuels. The focus of this paper is to do analysis how the ammonia dosage to SCR affects to the NOx formation in exhaust gasses on various engine speed (loads), as well as how it affects to some important engine parameters and specific fuel oil consumption (SFOC). The analysis was performed on Kongsberg engine room simulator (ERS), MC 90-V Model, as well as on MATLAB by using mathematical models. All external influences are excluded from the analysis like wind or rough sea. All data on different scenarios has been recorded after prolonged period to avoid inconsistencies. The results are shown graphically, and conclusions arc presented.


  • Deviations and errors review on measuring and calculating heavy fuel oil consumption and fuel stock onboard vessels equipped with volumetric fuel consumption flowmeters

    by Josip Dujmović, Dean Bernečić

    A common way of measuring heavy fuel oil consumption on board a vessel is to use volumetric fuel flow meters installed at fuel systems inlets for each of the major fuel consumers. At each stage of the fuel processing cycle, certain mass fuel losses or deviations and calculation errors occur that are not counted accurately into fuel consumption figures. The goal of this paper is to identify those fuel mass losses and measuring/calculating errors and perform their quantitative numerical analysis based on actual data. Fuel mass losses defined as deviations identified during the fuel preparation process are evaporation of volatile organic compounds, water drainage, fuel separation, and leakages while errors identified are flow meter accuracy and volumetric/mass flow conversion accuracy. By utilizing statistical analysis of obtained data from engine logbook extracts from three different ships numerical models were generated for each fuel mass loss point. Measuring errors and volumetric/mass conversion errors are numerically analyzed based on actual equipment and models used onboard example vessels. By computational analysis of the obtained models, approximate percentage losses and errors are presented as a fraction of fuel quantity on board or as a fraction of fuel consumed. Those losses and errors present between 0,001% and 5% of fuel stock or fuel consumption figures for each identified loss/error point. This paper presents a contribution for more accurate heavy fuel oil consumption calculation and consequently accurate declaration of remaining fuel stock onboard. It also presents a base for possible further research on the possible influence of fuel grade, fuel water content on the accuracy of consumption calculation.