Fuat Kucuk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Fuat Kucuk has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Yu Than
Faculty of Engineering, Kyoto University of Advanced Science, Kyoto 615-0096, Japan
2 shared publications - Erkan Sunan
TUBITAK Marmara Res Ctr, Energy Inst, Kocaeli, Turkey
1 shared publication - Rohan D. Mendonca
Graduate School of Engineering, Kyoto University of Advanced Science, Kyoto, Japan
1 shared publication - Sadra Mousavi
Dept. of Electrical Engineering, Istanbul Technical University, Istanbul, Turkey
1 shared publication
Latest Publications
- Open Access
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 100741-100750
Online Temperature Estimation of Three-Phase SCIM Using Low-Order LPTN Model
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 100741-100750
Open AccessOnline Temperature Estimation of Three-Phase SCIM Using Low-Order LPTN Model
- Open Access
A Novel Hill Climb Search-Based Magnetization Control for Low Coercivity Electro-Permanent Magnet Systems
Conventional electro-permanent magnet (EPM) lifting/holding systems, typically based on NdFeB magnets, face efficiency limitations because continuous current is required either for standby condition to avoid accidentally attracting the objects around or for gently approaching and separating from sensitive iron-based target objects during gripping and releasing processes. Low Coercive Force (LCF) magnets offer an alternative, as their magnetization can be tuned with short current pulses and maintained without continuous current. However, this approach demands fast and precise flux control to eliminate the issues mentioned above. This paper introduces a novel flux control method based on the Hill Climb Search (HCS) algorithm. Once the required flux is identified, the system rapidly adjusts the magnetization of LCF magnet by applying optimized pulse trains within a short time. Experimental evaluation confirms that the proposed method effectively establishes and sustains the target magnetization level without additional current input. This approach has significant potential to advance and expand the use of Low Coercivity EPM systems as an alternative to classical systems.
Open AccessA Novel Hill Climb Search-Based Magnetization Control for Low Coercivity Electro-Permanent Magnet Systems
Conventional electro-permanent magnet (EPM) lifting/holding systems, typically based on NdFeB magnets, face efficiency limitations because continuous current is required either for standby condition to avoid accidentally attracting the objects around or for gently approaching and separating from sensitive iron-based target objects during gripping and releasing processes. Low Coercive Force (LCF) magnets offer an alternative, as their magnetization can be tuned with short current pulses and maintained without continuous current. However, this approach demands fast and precise flux control to eliminate the issues mentioned above. This paper introduces a novel flux control method based on the Hill Climb Search (HCS) algorithm. Once the required flux is identified, the system rapidly adjusts the magnetization of LCF magnet by applying optimized pulse trains within a short time. Experimental evaluation confirms that the proposed method effectively establishes and sustains the target magnetization level without additional current input. This approach has significant potential to advance and expand the use of Low Coercivity EPM systems as an alternative to classical systems.
- Open Access
Comprehensive Investigation of Efficiency Improvement in Voltage Source Inverter Using Hybrid Carrier-Based Modulation
Voltage Source Inverters (VSIs) are essential in variable-speed drive applications, where Pulse-Width Modulation (PWM) signals are typically generated using a fixed-carrier (FC) signal. Increasing the FC frequency helps smoothen the inverter’s output current, improving motor performance. However, this comes at the expense of increased switching losses, reduced efficiency, and potential thermal management challenges. The Hybrid Carrier-based PWM (HCPWM) technique presents an alternative by dynamically alternating between two sawtooth carrier signals with different frequencies. This method aims to achieve higher efficiency without compromising system performance. However, selecting optimal carrier pairs to maximize efficiency across various speed and load conditions while maintaining total harmonic distortion within acceptable limits remains a challenge. This study provides a comprehensive experimental evaluation of the HCPWM approach, benchmarking it against conventional FCPWM. The results demonstrate that HCPWM enhances energy efficiency under all tested conditions, making it a viable and cost-effective solution for VSI-driven motor applications without introducing additional system cost or complexity.
Open AccessComprehensive Investigation of Efficiency Improvement in Voltage Source Inverter Using Hybrid Carrier-Based Modulation
Voltage Source Inverters (VSIs) are essential in variable-speed drive applications, where Pulse-Width Modulation (PWM) signals are typically generated using a fixed-carrier (FC) signal. Increasing the FC frequency helps smoothen the inverter’s output current, improving motor performance. However, this comes at the expense of increased switching losses, reduced efficiency, and potential thermal management challenges. The Hybrid Carrier-based PWM (HCPWM) technique presents an alternative by dynamically alternating between two sawtooth carrier signals with different frequencies. This method aims to achieve higher efficiency without compromising system performance. However, selecting optimal carrier pairs to maximize efficiency across various speed and load conditions while maintaining total harmonic distortion within acceptable limits remains a challenge. This study provides a comprehensive experimental evaluation of the HCPWM approach, benchmarking it against conventional FCPWM. The results demonstrate that HCPWM enhances energy efficiency under all tested conditions, making it a viable and cost-effective solution for VSI-driven motor applications without introducing additional system cost or complexity.
- 28 September 2018
- Published by The Scientific and Technological Research Council of Turkey (TUBITAK-ULAKBIM) - DIGITAL COMMONS JOURNALS in Turkish Journal of Electrical Engineering and Computer Sciences
- Vol. 26 (5) , 2701-2713
Full bridge converter based independent phase control of a permanent magnet reluctance generator for wind power conversion systems
- 28 September 2018
- Published by The Scientific and Technological Research Council of Turkey (TUBITAK-ULAKBIM) - DIGITAL COMMONS JOURNALS in Turkish Journal of Electrical Engineering and Computer Sciences
- Vol. 26 (5) , 2701-2713
Full bridge converter based independent phase control of a permanent magnet reluctance generator for wind power conversion systems
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 22-25
Development of a novel Coaxial Magnetic Gear
Magnetic Gears (MGs) offer many advantages compared to mechanical gears such as reduced maintenance, high reliability and inherent over load protection. Among various MGs, a Surface Permanent Magnet (SPM) type Coaxial Magnetic Gear (CMG), which may be accepted to be a classical CMG, is may be preferable owing to its high torque transmission capability. The main drawback of this CMG is that the gear ratio as well as efficiency is highly affected by the speed increase due to severe Eddy current losses in permanent magnets. Having permanent magnets on the outer side of the rotor is another drawback of the classical CMG since these magnets are experience sever centrifugal forces as the speed increases and thus the MG may encounter serious damages. In order to overcome the mentioned drawbacks of classical CMGs, this paper introduces a new type CMG whose inner part contains interior permanent magnets (IPMs) rather than SPMs. A finite element based tool has been used to design the proposed magnetic gear and its performance has been investigated and compared with those of conventional CMG for various speed conditions. According to the analysis results, decrease in gear ratio with respect to the speed is significantly suppressed and thus efficiency is improved. Additionally, proposed CMG provides less amount of torque ripples.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 22-25
Development of a novel Coaxial Magnetic Gear
Magnetic Gears (MGs) offer many advantages compared to mechanical gears such as reduced maintenance, high reliability and inherent over load protection. Among various MGs, a Surface Permanent Magnet (SPM) type Coaxial Magnetic Gear (CMG), which may be accepted to be a classical CMG, is may be preferable owing to its high torque transmission capability. The main drawback of this CMG is that the gear ratio as well as efficiency is highly affected by the speed increase due to severe Eddy current losses in permanent magnets. Having permanent magnets on the outer side of the rotor is another drawback of the classical CMG since these magnets are experience sever centrifugal forces as the speed increases and thus the MG may encounter serious damages. In order to overcome the mentioned drawbacks of classical CMGs, this paper introduces a new type CMG whose inner part contains interior permanent magnets (IPMs) rather than SPMs. A finite element based tool has been used to design the proposed magnetic gear and its performance has been investigated and compared with those of conventional CMG for various speed conditions. According to the analysis results, decrease in gear ratio with respect to the speed is significantly suppressed and thus efficiency is improved. Additionally, proposed CMG provides less amount of torque ripples.