Ammar A. Alhayani
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ammar A. Alhayani has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Asaad Almssad
Department of Engineering and Chemical Sciences, Karlstad University, 65188 Karlstad, Sweden
3 shared publications - Majid Al-Gburi
Building and Construction Techniques Engineering, Northern Technical University , Mosul , Iraq
3 shared publications - Duaa H. Ahmad
Postgraduate Student in Construction Materials Technology Engineering, Engineering Technical College of Mosul, Northern Technical University, Mosul, Iraq
1 shared publication Fatima A. Mohammed
1 shared publication- Hesham Salim Al-Rawe
Department of Building & Construction Engineering Technology, Technical College of Building & Architecture Engineering, Northern Technical University, Mosul 41001, Iraq
1 shared publication Nisreen W. Abdullatif
Engineering Technical College of Mosul Northern Technical University Mosul Iraq
1 shared publication
Latest Publications
- Open Access
A Comprehensive Database-Driven Analysis of Size Effect on Shear Strength of Reinforced Concrete Beams Without Stirrups: From Statistical Biases to Advanced Predictive Modelling
In the current paper, an investigation into the influence of the size effect on the shear strength of unreinforced concrete beams using a data-driven approach including statistical analysis, calibration, and prediction is carried out. The database consists of 804 test results collected from 41 sources and covers a wide range of effective depths (44–1670 mm), reinforcement ratios (0.26–15.23%) and shear span-to-depth ratios (0.39–9.76). The dependent variable was carefully validated and recalculated based on the maximum load to avoid transcription mistakes. As a result of the statistical analysis, biases and correlations were found between the effective depth and the reinforcement ratio, which lead to misinterpretation of the size effect in the univariate case. The calibration of Bazant’s Size Effect Law proved that the transitional size parameter (d0) varies from 90.1 mm to 1000 mm depending on the reinforcement ratio. To make a fair comparison of nominal to nominal, the formulation of ACI 318-19 included the size effect factor λ, while the partial safety factor γc was not included in Eurocode 2. It was found that both the codes are extremely conservative, with percentage bias (PBIAS) of −45.9% in the case of ACI, and −26.8% in the case of EC2. The suggested GPR model has yielded a very high R2 value of 0.713 and near- zero aggregate bias (PBIAS = −4.4%). With the help of statistical tests such as the Wilcoxon signed-rank test, it was proved that the GPR performs significantly better than ACI (p = 6.37 × 10−21) and Eurocode 2 (p = 4.95 × 10−7). Even though GPR under-predicts on aggregate (conservative), it offers a good 95% prediction interval (coverage of 90.6%). Thus, a safety factor of 1.05 is suggested. The results from a sensitivity analysis based on the random forest feature importance revealed that the most sensitive parameters are the a/d ratio and the a/d ratio by the size factor (kd), which contribute 24.1% and 12.2% to the total variance, respectively. The proposed approach will be very helpful in designing shear safely and economically.
Open AccessA Comprehensive Database-Driven Analysis of Size Effect on Shear Strength of Reinforced Concrete Beams Without Stirrups: From Statistical Biases to Advanced Predictive Modelling
In the current paper, an investigation into the influence of the size effect on the shear strength of unreinforced concrete beams using a data-driven approach including statistical analysis, calibration, and prediction is carried out. The database consists of 804 test results collected from 41 sources and covers a wide range of effective depths (44–1670 mm), reinforcement ratios (0.26–15.23%) and shear span-to-depth ratios (0.39–9.76). The dependent variable was carefully validated and recalculated based on the maximum load to avoid transcription mistakes. As a result of the statistical analysis, biases and correlations were found between the effective depth and the reinforcement ratio, which lead to misinterpretation of the size effect in the univariate case. The calibration of Bazant’s Size Effect Law proved that the transitional size parameter (d0) varies from 90.1 mm to 1000 mm depending on the reinforcement ratio. To make a fair comparison of nominal to nominal, the formulation of ACI 318-19 included the size effect factor λ, while the partial safety factor γc was not included in Eurocode 2. It was found that both the codes are extremely conservative, with percentage bias (PBIAS) of −45.9% in the case of ACI, and −26.8% in the case of EC2. The suggested GPR model has yielded a very high R2 value of 0.713 and near- zero aggregate bias (PBIAS = −4.4%). With the help of statistical tests such as the Wilcoxon signed-rank test, it was proved that the GPR performs significantly better than ACI (p = 6.37 × 10−21) and Eurocode 2 (p = 4.95 × 10−7). Even though GPR under-predicts on aggregate (conservative), it offers a good 95% prediction interval (coverage of 90.6%). Thus, a safety factor of 1.05 is suggested. The results from a sensitivity analysis based on the random forest feature importance revealed that the most sensitive parameters are the a/d ratio and the a/d ratio by the size factor (kd), which contribute 24.1% and 12.2% to the total variance, respectively. The proposed approach will be very helpful in designing shear safely and economically.
- Open Access
A Transparent ANN–Excel Model for Shear Strength of Steel Fiber-Reinforced Concrete Beams: Parametric Analysis, and Design Implications
In this paper, an ANN-based model is suggested for the prediction of shear strength of steel fiber-reinforced concrete (SFRC) beams without transverse reinforcements, and the model is developed directly using Excel software to ensure computational transparency and statistical interpretability, while remaining an empirical data-driven tool. In this study, a comprehensive database including 923 experimental data is collected, prepared and utilized to develop the neural network. Following the completion of the learning process, the ultimate weight and bias for the neural network are obtained. These parameters are employed in the Excel worksheet. With this process, the learned model is converted into a standalone and operational design tool. Sensitivity analysis, which has been performed through a step-by-step and perturbation method, revealed that the beam width (b) is the most influential parameter in the determination of shear strength (33.4%), followed by concrete compressive strength (fc, 17.1%) and effective depth (d, 15.3%). Then, a parametric study is conducted to study the effect of the shear span-to-depth ratio (a/d), longitudinal reinforcement ratio (ρ) and fiber aspect ratio (Lf/df) on the shear behavior of the members.
Open AccessA Transparent ANN–Excel Model for Shear Strength of Steel Fiber-Reinforced Concrete Beams: Parametric Analysis, and Design Implications
In this paper, an ANN-based model is suggested for the prediction of shear strength of steel fiber-reinforced concrete (SFRC) beams without transverse reinforcements, and the model is developed directly using Excel software to ensure computational transparency and statistical interpretability, while remaining an empirical data-driven tool. In this study, a comprehensive database including 923 experimental data is collected, prepared and utilized to develop the neural network. Following the completion of the learning process, the ultimate weight and bias for the neural network are obtained. These parameters are employed in the Excel worksheet. With this process, the learned model is converted into a standalone and operational design tool. Sensitivity analysis, which has been performed through a step-by-step and perturbation method, revealed that the beam width (b) is the most influential parameter in the determination of shear strength (33.4%), followed by concrete compressive strength (fc, 17.1%) and effective depth (d, 15.3%). Then, a parametric study is conducted to study the effect of the shear span-to-depth ratio (a/d), longitudinal reinforcement ratio (ρ) and fiber aspect ratio (Lf/df) on the shear behavior of the members.
- Open Access
- 31 December 2025
- Published by International Information and Engineering Technology Association in Revue des composites et des matériaux avancés
- Vol. 35 (6)
Influence of Nanomaterials on the Performance of Lightweight Concrete Containing Silica Fume Against Chemical Attacks
- 31 December 2025
- Published by International Information and Engineering Technology Association in Revue des composites et des matériaux avancés
- Vol. 35 (6)
Open AccessInfluence of Nanomaterials on the Performance of Lightweight Concrete Containing Silica Fume Against Chemical Attacks
- Open Access
Artificial Neural Network Model for Evaluating Load Capacity of RC Deep Beams
Using artificial neural networks (ANN), numerous models were developed for predicting the ultimate shear strength of reinforced concrete deep beams. Many experimental result databases from earlier research were carefully gathered for this study. Two hundred fifty-three findings from experiments were included in this database. The ultimate shear strength was the output parameter, while ten factors were determined as input parameters for the ANN model based on the completed literature research. The required model was constructed using a back propagation neural network. The model of the neural networks was determined using the trial-and-error method. It was discovered that, inside the range of the input boundaries considered, the ANN model could accurately estimate the ultimate shear strength of deep beams. The measured shear strength and the shear strength predicted by the ANN model have a high correlation coefficient of 0.97, indicating a strong relationship between the predicted and actual values. The results show that, given the range of input parameters, ANN offers an excellent agreement of interest as a practical technique for estimating the ultimate shear strength. A parametric investigation was performed using the trained neural network model to assess how the input parameters affected the shear strength capacity of deep beams.
Open AccessArtificial Neural Network Model for Evaluating Load Capacity of RC Deep Beams
Using artificial neural networks (ANN), numerous models were developed for predicting the ultimate shear strength of reinforced concrete deep beams. Many experimental result databases from earlier research were carefully gathered for this study. Two hundred fifty-three findings from experiments were included in this database. The ultimate shear strength was the output parameter, while ten factors were determined as input parameters for the ANN model based on the completed literature research. The required model was constructed using a back propagation neural network. The model of the neural networks was determined using the trial-and-error method. It was discovered that, inside the range of the input boundaries considered, the ANN model could accurately estimate the ultimate shear strength of deep beams. The measured shear strength and the shear strength predicted by the ANN model have a high correlation coefficient of 0.97, indicating a strong relationship between the predicted and actual values. The results show that, given the range of input parameters, ANN offers an excellent agreement of interest as a practical technique for estimating the ultimate shear strength. A parametric investigation was performed using the trained neural network model to assess how the input parameters affected the shear strength capacity of deep beams.
- Open Access
- 1 January 2025
- Published by MIM Research Group in Research on Engineering Structures and Materials
Shear and flexural strength of pumice lightweight concrete beams with silica fume
Recently, many types of research in Iraq have had the properties of lightweight concrete beams utilizing both artificial and normal aggregate for economic reasons. Very limited works have been implemented to investigate the resistance of flexural and shear behavior of structural lightweight aggregate concrete; therefore, it is important to study the properties and their structural behavior. The present work is to investigate the shear and flexural strength of lightweight concrete beams made of pumice with silica fume admixture. The lightweight concrete has been made by partial replacement of crushed gravel with 75% pumice and 7% silica fume. The value of compressive force strength is 29 MPa within twenty-eight days. A total of ten reinforced concrete beams is used, with dimensions of (150 x 150 x 750) mm, with and without silica fume, and with varying ratios of transverse reinforcement (stirrups). The deflection at mid-span was also measured using a mechanical dial gauge. Normal-weight concrete beams are also used for comparison with the lightweight concrete beams. Beam behavior was assessed in terms of ultimate deflection, failure mode, and crack pattern. According to the experimental results, the prepared concrete's weight and strength met the LWC requirements. The results showed a significant effect of the transverse reinforcement ratio (stirrups), where the values of the shear and resistance of flexural rose when the amount of reinforcement increased. Furthermore, the appearance of the first crack has been significantly delayed as the reinforcement ratio rose.
- 1 January 2025
- Published by MIM Research Group in Research on Engineering Structures and Materials
Open AccessShear and flexural strength of pumice lightweight concrete beams with silica fume
Recently, many types of research in Iraq have had the properties of lightweight concrete beams utilizing both artificial and normal aggregate for economic reasons. Very limited works have been implemented to investigate the resistance of flexural and shear behavior of structural lightweight aggregate concrete; therefore, it is important to study the properties and their structural behavior. The present work is to investigate the shear and flexural strength of lightweight concrete beams made of pumice with silica fume admixture. The lightweight concrete has been made by partial replacement of crushed gravel with 75% pumice and 7% silica fume. The value of compressive force strength is 29 MPa within twenty-eight days. A total of ten reinforced concrete beams is used, with dimensions of (150 x 150 x 750) mm, with and without silica fume, and with varying ratios of transverse reinforcement (stirrups). The deflection at mid-span was also measured using a mechanical dial gauge. Normal-weight concrete beams are also used for comparison with the lightweight concrete beams. Beam behavior was assessed in terms of ultimate deflection, failure mode, and crack pattern. According to the experimental results, the prepared concrete's weight and strength met the LWC requirements. The results showed a significant effect of the transverse reinforcement ratio (stirrups), where the values of the shear and resistance of flexural rose when the amount of reinforcement increased. Furthermore, the appearance of the first crack has been significantly delayed as the reinforcement ratio rose.
- 23 December 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 61, 1140-1148
Investigation the influence of nano ceramic on the mechanical properties and shrinkage of lightweight concrete containing silica fume
- 23 December 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 61, 1140-1148
Investigation the influence of nano ceramic on the mechanical properties and shrinkage of lightweight concrete containing silica fume