Swami Nath Maurya
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Swami Nath Maurya has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Win-Jet Luo
Graduate Institute of Precision Manufacturing, National Chin-Yi University of Technology, Taichung, Taiwan
5 shared publications - Amir Reza Ansari Dezfoli
Ph.D. Program at Graduate Institute of Precision Manufacturing, National Chin-Yi University of Technology, Taichung, Taiwan
3 shared publications - Bivas Panigrahi
Department of Refrigeration, Air Conditioning and Energy Engineering, National Chin-Yi University of Technology, Taichung 41170, Taiwan
3 shared publications - Kun-Ying Li
Department of Intelligent Automation Engineering, National Chin-Yi University of Technology, Taichung, Taiwan
3 shared publications - Prateek Negi
Graduate Institute of Precision Manufacturing, National Chin-Yi University of Technology, Taichung, Taiwan
2 shared publications Win-Jet Luo
2 shared publications
Latest Publications
- Open Access
- 19 June 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (13)
Feature-Based 1D-CNN for Intelligent Fault Localization in Power Transformer Cores
Accurate fault localization in power transformer cores is critical for ensuring system reliability and preventing catastrophic failures. Conventional diagnostic techniques, including vibration analysis and thermal monitoring, are often limited by low spatial resolution, sensitivity to operating conditions, and reliance on manual interpretation. Recent deep learning approaches have improved fault detection; however, most existing studies focus on classification using raw signals and lack robustness to load variations, while offering limited capability for precise fault localization within transformer cores. To address these challenges, this study proposes a feature-based one-dimensional convolutional neural network (1D-CNN) for intelligent fault localization using vibration signal analysis. Instead of relying on raw data, the proposed model integrates domain-specific features, including fast fourier transform (FFT) components and time-delay estimation derived from cross-correlation (TDOA), to construct a compact and informative feature matrix. A lightweight 1D-CNN model is then trained to classify fault locations across transformer core limbs under varying load conditions. Experimental validation on a 2 kVA transformer demonstrates that the proposed model achieves high localization accuracy up to 99.34%, with improved robustness compared with previously developed deep learning models. The results confirm that the feature-based design enhances interpretability while reducing computational complexity, making it suitable for real-time condition monitoring applications.
- 19 June 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (13)
Open AccessFeature-Based 1D-CNN for Intelligent Fault Localization in Power Transformer Cores
Accurate fault localization in power transformer cores is critical for ensuring system reliability and preventing catastrophic failures. Conventional diagnostic techniques, including vibration analysis and thermal monitoring, are often limited by low spatial resolution, sensitivity to operating conditions, and reliance on manual interpretation. Recent deep learning approaches have improved fault detection; however, most existing studies focus on classification using raw signals and lack robustness to load variations, while offering limited capability for precise fault localization within transformer cores. To address these challenges, this study proposes a feature-based one-dimensional convolutional neural network (1D-CNN) for intelligent fault localization using vibration signal analysis. Instead of relying on raw data, the proposed model integrates domain-specific features, including fast fourier transform (FFT) components and time-delay estimation derived from cross-correlation (TDOA), to construct a compact and informative feature matrix. A lightweight 1D-CNN model is then trained to classify fault locations across transformer core limbs under varying load conditions. Experimental validation on a 2 kVA transformer demonstrates that the proposed model achieves high localization accuracy up to 99.34%, with improved robustness compared with previously developed deep learning models. The results confirm that the feature-based design enhances interpretability while reducing computational complexity, making it suitable for real-time condition monitoring applications.
- Open Access
- 22 July 2025
- Published by IOP Publishing in Materials Research Express
- Vol. 12 (9)
Performance analysis of energy recovery membrane coated with graphene oxide
Heating, Ventilation, and Air Conditioning (HVAC) systems account for approximately 50% of the total energy consumption in residential and commercial buildings, providing thermal comfort alongside lighting, water heating/ cooling, and equipment operation. This study investigates the performance of energy recovery ventilators (ERVs) incorporating Graphene Oxide (GO)-coated membranes under varying operational conditions. The composite membranes were fabricated by depositing a GO layer onto a cellulose acetate support, with thicknesses of 0.77 µm, 1.87 µm, and 2.7 µm. Results showed that thicker membranes significantly reduced CO2 crossover, with the lowest crossover observed at a thickness of 2.7 µm and a GO concentration of 1 mg/ml. The GO-coated membrane with a 2.7 µm thickness also exhibited the highest latent heat effectiveness. At this optimal thickness, the maximum sensible, latent, and enthalpy effectiveness values reached 93%, 72%, and 75%, respectively. These peak performances were achieved at an inlet air temperature of 35 °C and 75% relative humidity. Optimal flow rates were identified as 2 LPM for maximum sensible effectiveness and 0.8 LPM for maximizing latent and enthalpy effectiveness. These findings demonstrate the potential of GO-coated membranes to enhance indoor air quality while significantly reducing energy losses and CO2 transfer, offering a promising approach for next generation HVAC systems in humid climates.
- 22 July 2025
- Published by IOP Publishing in Materials Research Express
- Vol. 12 (9)
Open AccessPerformance analysis of energy recovery membrane coated with graphene oxide
Heating, Ventilation, and Air Conditioning (HVAC) systems account for approximately 50% of the total energy consumption in residential and commercial buildings, providing thermal comfort alongside lighting, water heating/ cooling, and equipment operation. This study investigates the performance of energy recovery ventilators (ERVs) incorporating Graphene Oxide (GO)-coated membranes under varying operational conditions. The composite membranes were fabricated by depositing a GO layer onto a cellulose acetate support, with thicknesses of 0.77 µm, 1.87 µm, and 2.7 µm. Results showed that thicker membranes significantly reduced CO2 crossover, with the lowest crossover observed at a thickness of 2.7 µm and a GO concentration of 1 mg/ml. The GO-coated membrane with a 2.7 µm thickness also exhibited the highest latent heat effectiveness. At this optimal thickness, the maximum sensible, latent, and enthalpy effectiveness values reached 93%, 72%, and 75%, respectively. These peak performances were achieved at an inlet air temperature of 35 °C and 75% relative humidity. Optimal flow rates were identified as 2 LPM for maximum sensible effectiveness and 0.8 LPM for maximizing latent and enthalpy effectiveness. These findings demonstrate the potential of GO-coated membranes to enhance indoor air quality while significantly reducing energy losses and CO2 transfer, offering a promising approach for next generation HVAC systems in humid climates.
- Open Access
- 15 July 2025
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 73
Performance and economic enhancement of a dewaxing casting process using a heat pump drying system
- 15 July 2025
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 73
Open AccessPerformance and economic enhancement of a dewaxing casting process using a heat pump drying system
- Open Access
- 2 June 2025
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 35 (6) , 065004
Efficient heat dissipation with hybrid composite-based microfluidic heat sinks in flexible electronics
Regulating unwanted heat generation has become a significant challenge in flexible electronic devices. Traditional heat sinks are typically rigid, bulky, and designed for conventional electronics. When designing a flexible heat sink, fundamental aspects such as thermal conductivity, specific heat capacity and elasticity must be taken into consideration. In this context, we present a flexible hybrid composite material engineered using polydimethylsiloxane (PDMS), graphene oxide (GO), and paraffin wax (PW) and propose a microfluidic heat sink device with spiral microchannel fabricated employing three-dimensional printed scaffold removal method followed by casting. The PDMS composite with 5% w/w PW and 5% w/w GO exhibited improved material characteristics in terms of thermal conductivity, specific heat capacity, and elasticity, making it ideal for microfluidic device fabrication. The performance of the microfluidic heat sink device was evaluated both experimentally and numerically under a constant heater temperature of 358 K, with flow rates varying from 40 to 240 μl min−1. The results demonstrated that at a relatively high flow rate of 240 μl min−1, the average hotspot temperature was approximately 4.3 K lower than its PDMS counterpart, emphasizing the significant influence of material properties and channel hydrodynamics.
- 2 June 2025
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 35 (6) , 065004
Open AccessEfficient heat dissipation with hybrid composite-based microfluidic heat sinks in flexible electronics
Regulating unwanted heat generation has become a significant challenge in flexible electronic devices. Traditional heat sinks are typically rigid, bulky, and designed for conventional electronics. When designing a flexible heat sink, fundamental aspects such as thermal conductivity, specific heat capacity and elasticity must be taken into consideration. In this context, we present a flexible hybrid composite material engineered using polydimethylsiloxane (PDMS), graphene oxide (GO), and paraffin wax (PW) and propose a microfluidic heat sink device with spiral microchannel fabricated employing three-dimensional printed scaffold removal method followed by casting. The PDMS composite with 5% w/w PW and 5% w/w GO exhibited improved material characteristics in terms of thermal conductivity, specific heat capacity, and elasticity, making it ideal for microfluidic device fabrication. The performance of the microfluidic heat sink device was evaluated both experimentally and numerically under a constant heater temperature of 358 K, with flow rates varying from 40 to 240 μl min−1. The results demonstrated that at a relatively high flow rate of 240 μl min−1, the average hotspot temperature was approximately 4.3 K lower than its PDMS counterpart, emphasizing the significant influence of material properties and channel hydrodynamics.
- 19 May 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 138 (7-8) , 3077-3087
Data-driven approach for optimizing the Czochralski process and predictive modeling: A finite element and machine learning analysis
- 19 May 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 138 (7-8) , 3077-3087
Data-driven approach for optimizing the Czochralski process and predictive modeling: A finite element and machine learning analysis
- 11 March 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 137 (5-6) , 2935-2946
Process parameter optimization in Czochralski growth of silicon ingots: a Monte Carlo-finite element coupled model
- 11 March 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 137 (5-6) , 2935-2946
Process parameter optimization in Czochralski growth of silicon ingots: a Monte Carlo-finite element coupled model
- 17 February 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 137 (1-2) , 755-763
Impact of top cooling on defect suppression in large-scale silicon ingot manufacturing
- 17 February 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 137 (1-2) , 755-763
Impact of top cooling on defect suppression in large-scale silicon ingot manufacturing
- 20 July 2024
- Published by Springer Nature in Food and Bioprocess Technology
- Vol. 18 (2) , 1125-1140
Substantial Enhancement of Overall Efficiency and Effectiveness of the Pasteurization and Packaging Process Using Artificial Intelligence in the Food Industry
- 20 July 2024
- Published by Springer Nature in Food and Bioprocess Technology
- Vol. 18 (2) , 1125-1140
Substantial Enhancement of Overall Efficiency and Effectiveness of the Pasteurization and Packaging Process Using Artificial Intelligence in the Food Industry
- 1 April 2024
- Published by Springer Nature in Journal of Intelligent Manufacturing
- Vol. 36 (4) , 2387-2408
Input attribute optimization for thermal deformation of machine-tool spindles using artificial intelligence
- 1 April 2024
- Published by Springer Nature in Journal of Intelligent Manufacturing
- Vol. 36 (4) , 2387-2408
Input attribute optimization for thermal deformation of machine-tool spindles using artificial intelligence
- 11 March 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 126 (3-4) , 1807-1825
Thermal deformation and economic analysis of a multiobject cooling system for spindles with varied coolant volume control
- 11 March 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 126 (3-4) , 1807-1825
Thermal deformation and economic analysis of a multiobject cooling system for spindles with varied coolant volume control