Ju. M. Ladytko
Research Subjects
Ju. M. Ladytko has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- A. L. Golovanenko
Perm State Pharmaceutical Academy, Perm, Russian Federation
1 shared publication - Alekseeva I.V.
Perm State Pharmaceutical Academy
1 shared publication - E. I. Molokhova
Federal State Budgetary Educational Institution of Higher Education "Perm State Pharmaceutical Academy" of the Ministry of Health of the Russian Federation
1 shared publication - E. I. Ponomareva
Perm State Pharmaceutical Academy
1 shared publication - E. S. Berezina
Federal State Budgetary Educational Institution of Higher Education "Perm State Pharmaceutical Academy" of the Ministry of Health of the Russian Federation
1 shared publication - Elena Flisyuk
Department of Pharmaceutical Formulations, St. Petersburg State Chemical Pharmaceutical University, 14a Prof. Popov Str., 197022 Saint-Petersburg, Russia
1 shared publication
Latest Publications
- Open Access
- 23 February 2022
- Published by Center of Pharmaceutical Analytics Ltd in Drug development & registration
- Vol. 11 (1) , 59-67
Transfer of Cosmetic Emulsion Cream Technology from Laboratory to Pilot Phase
Introduction. When transferring the technology of cosmetic emulsion cream from laboratory conditions to semi-industrial equipment, it is necessary to determine the critical process parameters that will allow achieving results without losing the quality of the final product.Aim. The aim of the study is to confirm the effectiveness of the developed technology for the production of emulsion cream under scaling conditions.Materials and methods. As active substances were used badan thick-leaved extract dry, salicylic acid, dimethicone, menthol and octypyrox; emollients – grape seed oil, coconut oil, castor oil; emulsifiers and co-emulsifiers – distilled monoglycerides, emulsion wax, anhydrous lanolin, Cremophor A25; humidifier – glycerin; alkaline agent, pH regulator – triethanolamine; preservative – Euxil 9010; fragrance – essential oil of rosewood, solvent – purified water. Phase mixing and emulsification were carried out in a PRS AR 403 planetary mixer (ERWEKA GmbH, Germany), dosing into a sealed plastic container was carried on an FDS II AR 403 ointment dosing unit (ERWEKA GmbH, Germany). The study of the physicochemical and structural-mechanical properties of the cream was carried out in accordance with GOST 29188.2-2014 and GOST 29188.3-91.Results and discussion. Under scaling conditions, 3 pilot series of cosmetic emulsion cream for the prevention of dry seborrhea of the scalp based of badan thick-leaved extract dry have been developed. The cream obtained both in the pilot and laboratory phases met all the requirements of the Technical Regulations of the Customs Union (TR CU) 009/2011 "On the safety of perfumery and cosmetic products", which confirms the reproducibility of the developed production technology. A 20-fold increase in loading did not affect the methods of introducing the components and their percentage. To determine the possibility of technology transfer from laboratory conditions to semi-industrial production conditions, the technological characteristics of the equipment were analyzed for the ability to carry out the required technological process, using the Ishikawa diagram, risks were identified and causal relationships of the production. The most important indicators of the technological process have been established – these are the temperature, the number of revolutions of the mixer and the mixing time.Conclusion. On the semi-industrial equipment of the GMP training center, the technology of obtaining a cosmetic emulsion cream based on badan thick-leaved extract dry. A causal diagram (Ishikawa diagram) was compiled. Taking into account possible risks in the production of emulsion cream (number of revolutions of the mixer, stirring time, temperature) made it possible to obtain a stable product that meets all the requirements of TR CU 009/2011 "On the safety of perfumery and cosmetic products". The reproducibility of the technological process is shown.
- 23 February 2022
- Published by Center of Pharmaceutical Analytics Ltd in Drug development & registration
- Vol. 11 (1) , 59-67
Open AccessTransfer of Cosmetic Emulsion Cream Technology from Laboratory to Pilot Phase
Introduction. When transferring the technology of cosmetic emulsion cream from laboratory conditions to semi-industrial equipment, it is necessary to determine the critical process parameters that will allow achieving results without losing the quality of the final product.Aim. The aim of the study is to confirm the effectiveness of the developed technology for the production of emulsion cream under scaling conditions.Materials and methods. As active substances were used badan thick-leaved extract dry, salicylic acid, dimethicone, menthol and octypyrox; emollients – grape seed oil, coconut oil, castor oil; emulsifiers and co-emulsifiers – distilled monoglycerides, emulsion wax, anhydrous lanolin, Cremophor A25; humidifier – glycerin; alkaline agent, pH regulator – triethanolamine; preservative – Euxil 9010; fragrance – essential oil of rosewood, solvent – purified water. Phase mixing and emulsification were carried out in a PRS AR 403 planetary mixer (ERWEKA GmbH, Germany), dosing into a sealed plastic container was carried on an FDS II AR 403 ointment dosing unit (ERWEKA GmbH, Germany). The study of the physicochemical and structural-mechanical properties of the cream was carried out in accordance with GOST 29188.2-2014 and GOST 29188.3-91.Results and discussion. Under scaling conditions, 3 pilot series of cosmetic emulsion cream for the prevention of dry seborrhea of the scalp based of badan thick-leaved extract dry have been developed. The cream obtained both in the pilot and laboratory phases met all the requirements of the Technical Regulations of the Customs Union (TR CU) 009/2011 "On the safety of perfumery and cosmetic products", which confirms the reproducibility of the developed production technology. A 20-fold increase in loading did not affect the methods of introducing the components and their percentage. To determine the possibility of technology transfer from laboratory conditions to semi-industrial production conditions, the technological characteristics of the equipment were analyzed for the ability to carry out the required technological process, using the Ishikawa diagram, risks were identified and causal relationships of the production. The most important indicators of the technological process have been established – these are the temperature, the number of revolutions of the mixer and the mixing time.Conclusion. On the semi-industrial equipment of the GMP training center, the technology of obtaining a cosmetic emulsion cream based on badan thick-leaved extract dry. A causal diagram (Ishikawa diagram) was compiled. Taking into account possible risks in the production of emulsion cream (number of revolutions of the mixer, stirring time, temperature) made it possible to obtain a stable product that meets all the requirements of TR CU 009/2011 "On the safety of perfumery and cosmetic products". The reproducibility of the technological process is shown.
- Open Access
- 24 December 2021
- Published by Center of Pharmaceutical Analytics Ltd in Drug development & registration
- Vol. 10 (4) , 63-68
Experimental substantiation of the composition of gelatin mass for obtaining capsules with essential oils
Introduction. Soft gelatin capsules are a promising dosage form comprising essential oils as active agents. Joint research of the staff of the Perm State Pharmaceutical Academy, the Research Institute of Nutrition of the Ministry of Energy and Industry of the Republic of Tajikistan have proposed the composition of gelatin mass for encapsulation by the rotary matrix method. The mechanical and physical-technological parameters required to preserve the strength and elasticity of the capsule shell during the production process and storage are determined.Aim. Study of the rheological properties of gelatin masses based on gelatin of different grades, as well as the migration of essential oils through capsule shells.Materials and methods. Pharmaceutical active substances "Lipovitol" and "Limoneol" obtained in the Republic of Tajikistan were used as active substances introduced into the composition of soft gelatin capsules. Sunflower oil was used as the solvent. Gelatin samples were used to obtain gelatin masses: 1 – Foodchem (China), 2 – Brodnickie Zaklady Zelatyny Sp. zo.o. (Poland), 3 - Italgelatine s.p.a. (Italy), 4 – Ewald-Gelatine GmbH (Germany), 5 – Weishardt International (France); glycerol; sunflower oil. Gelatin mass for manufacturing soft capsules was prepared in a closed reactor. Capsules were prepared on an automatic encapsulation line RJWJ – 115 Soft Gelatin Encapsulator Machine (China). The structural and mechanical properties of soft gelatin masses were determined on a rotary viscometer RV type "Reotest 2" (Germany). The dynamics of the process of migration of essential oils and its components were studied by changing their amount in a capsule by chromato-mass spectrometry method on a chromatograph Varian CP 3800 with a quadrupole mass spectrometer 4000 MS as a detector (USA).Results and discussion. When studying the rheological properties of model compositions, it was found that for all samples of gelatin masses there is a decrease in values of effective viscosity when the shear rate increases, which characterizes the tested samples as a structured dispersion system. Additional studies have shown that the gelatin masses have thixotropic properties. Samples of gelatin masses 3–5 had narrower hysteresis loops, while sample 5 the narrowest, restoration of the structure took place quite quickly. Capsules obtained from gelatin mass 3 and 4 samples had a strong seam and were well cut out of the tape. From the mass of sample 5, high strength ribbons were obtained, a high temperature was required to seal the capsules, in some capsules the seam was not glued on one side, as a result, the capsules were rigid and brittle. As a result of the study, the rheological optimum of the gelatin mass suitable for preparing capsules by a rotary matrix method was determined, which has boundaries in the ranges of shear rates of 0.556–243 s-1 and viscosity ranges of 11.46-5028.76 Pa ⋅ s and shear stress of 2788–2808 Pa developing at these rates. When studying the migration of active substances through the capsule shell, it was found that over three years of storage of capsules in a closed polymer can, the content of essential oil in Lipovitol capsules decreased by 4.88 %, in Limoneol capsules by 5 %, which indicates partial migration of oil through the gelatin shell. The content remained within the permissible deviations (±10 %). The content of essential essential oil components also remained within acceptable deviations throughout the shelf life.Conclusion. The optimal composition of the shell for producing soft capsules by a rotary matrix method is justified. It was found that the rheological optimum of gelatin mass is characterized by viscosity ranges of 11.46-5028.76 Pa ⋅ s and shear stress of 2788–2808 Pa. According to the results of the study of the migration of essential oils through the shell, has been established the shelf life of soft gelatin capsules in glass jars made of dark glass and a temperature of 15 to 25 °C – 3 years.
- 24 December 2021
- Published by Center of Pharmaceutical Analytics Ltd in Drug development & registration
- Vol. 10 (4) , 63-68
Open AccessExperimental substantiation of the composition of gelatin mass for obtaining capsules with essential oils
Introduction. Soft gelatin capsules are a promising dosage form comprising essential oils as active agents. Joint research of the staff of the Perm State Pharmaceutical Academy, the Research Institute of Nutrition of the Ministry of Energy and Industry of the Republic of Tajikistan have proposed the composition of gelatin mass for encapsulation by the rotary matrix method. The mechanical and physical-technological parameters required to preserve the strength and elasticity of the capsule shell during the production process and storage are determined.Aim. Study of the rheological properties of gelatin masses based on gelatin of different grades, as well as the migration of essential oils through capsule shells.Materials and methods. Pharmaceutical active substances "Lipovitol" and "Limoneol" obtained in the Republic of Tajikistan were used as active substances introduced into the composition of soft gelatin capsules. Sunflower oil was used as the solvent. Gelatin samples were used to obtain gelatin masses: 1 – Foodchem (China), 2 – Brodnickie Zaklady Zelatyny Sp. zo.o. (Poland), 3 - Italgelatine s.p.a. (Italy), 4 – Ewald-Gelatine GmbH (Germany), 5 – Weishardt International (France); glycerol; sunflower oil. Gelatin mass for manufacturing soft capsules was prepared in a closed reactor. Capsules were prepared on an automatic encapsulation line RJWJ – 115 Soft Gelatin Encapsulator Machine (China). The structural and mechanical properties of soft gelatin masses were determined on a rotary viscometer RV type "Reotest 2" (Germany). The dynamics of the process of migration of essential oils and its components were studied by changing their amount in a capsule by chromato-mass spectrometry method on a chromatograph Varian CP 3800 with a quadrupole mass spectrometer 4000 MS as a detector (USA).Results and discussion. When studying the rheological properties of model compositions, it was found that for all samples of gelatin masses there is a decrease in values of effective viscosity when the shear rate increases, which characterizes the tested samples as a structured dispersion system. Additional studies have shown that the gelatin masses have thixotropic properties. Samples of gelatin masses 3–5 had narrower hysteresis loops, while sample 5 the narrowest, restoration of the structure took place quite quickly. Capsules obtained from gelatin mass 3 and 4 samples had a strong seam and were well cut out of the tape. From the mass of sample 5, high strength ribbons were obtained, a high temperature was required to seal the capsules, in some capsules the seam was not glued on one side, as a result, the capsules were rigid and brittle. As a result of the study, the rheological optimum of the gelatin mass suitable for preparing capsules by a rotary matrix method was determined, which has boundaries in the ranges of shear rates of 0.556–243 s-1 and viscosity ranges of 11.46-5028.76 Pa ⋅ s and shear stress of 2788–2808 Pa developing at these rates. When studying the migration of active substances through the capsule shell, it was found that over three years of storage of capsules in a closed polymer can, the content of essential oil in Lipovitol capsules decreased by 4.88 %, in Limoneol capsules by 5 %, which indicates partial migration of oil through the gelatin shell. The content remained within the permissible deviations (±10 %). The content of essential essential oil components also remained within acceptable deviations throughout the shelf life.Conclusion. The optimal composition of the shell for producing soft capsules by a rotary matrix method is justified. It was found that the rheological optimum of gelatin mass is characterized by viscosity ranges of 11.46-5028.76 Pa ⋅ s and shear stress of 2788–2808 Pa. According to the results of the study of the migration of essential oils through the shell, has been established the shelf life of soft gelatin capsules in glass jars made of dark glass and a temperature of 15 to 25 °C – 3 years.
- Open Access
- 24 December 2021
- Published by Center of Pharmaceutical Analytics Ltd in Drug development & registration
- Vol. 10 (4) , 54-62
Prediction of the composition of prolonged release tablets based on 4,4'-(propandiamido) sodium dibenzoate using the SeDeM method
Introduction. Direct compression technology is one of the most common tablet technologies. As known, many active pharmaceutical ingredients are not suitable for this technology without the addition of special excipients. A useful tool for determining the suitability of powdered materials for direct compression technology is the Sediment Delivery Model (SeDeM) method, based on the concept of Quality by Design. The presented method allows not only to assess the suitability of a material for direct compression, but also helps to predict the composition of a solid dosage form in the form of a tablet, which, in turn, leads to a significant reduction in experimental work carried out in the development of a new drug.Aim. Prediction of the compositions of matrix tablets based on sodium 4,4'-(propanediamido)dibenzoate with prolonged release, obtained by direct compression using the method of mathematical modeling SeDeM.Materials and methods. The objects of the study were the original substance sodium 4,4'-(propanediamido)dibenzoate, as well as a number of auxiliary substances, which included polymers used for dosage forms with prolonged release, a dusting component – magnesium stearate, and a filler – lactose monohydrate. Physicochemical and technological properties of APIs, explosives, obtained tablet mixtures and tablets were studied in accordance with the requirements of the State Pharmacopoeia of the Russian Federation XIV ed. and EP 9th ed.Results and discussion. The properties of the substance and excipients were assessed in accordance with the SeDeM method. It was found that the substance 4,4'-(propanediamido) sodium dibenzoate is not suitable for direct pressing due to poor flowability and low compressibility. Hypromellose Methocel K4M had good compressibility, but it did not have sufficient flowability. The other tested polymers had satisfactory properties for the direct compression technology. The composition of the tablet mixtures was calculated using the SeDeM method, the obtained tablet mixtures had satisfactory technological characteristics for obtaining tablets by direct compression. The tablets obtained as a result of the experiment also met the pharmacopoeial requirements.Conclusion. Prediction of the composition of sustained-release tablets based on the original substance sodium 4,4'-(propanediamido)dibenzoate was carried out using the SeDeM method. It was found that this method is suitable for the development of the composition of tablets based on sodium 4,4'-(propanediamido)dibenzoate.
- 24 December 2021
- Published by Center of Pharmaceutical Analytics Ltd in Drug development & registration
- Vol. 10 (4) , 54-62
Open AccessPrediction of the composition of prolonged release tablets based on 4,4'-(propandiamido) sodium dibenzoate using the SeDeM method
Introduction. Direct compression technology is one of the most common tablet technologies. As known, many active pharmaceutical ingredients are not suitable for this technology without the addition of special excipients. A useful tool for determining the suitability of powdered materials for direct compression technology is the Sediment Delivery Model (SeDeM) method, based on the concept of Quality by Design. The presented method allows not only to assess the suitability of a material for direct compression, but also helps to predict the composition of a solid dosage form in the form of a tablet, which, in turn, leads to a significant reduction in experimental work carried out in the development of a new drug.Aim. Prediction of the compositions of matrix tablets based on sodium 4,4'-(propanediamido)dibenzoate with prolonged release, obtained by direct compression using the method of mathematical modeling SeDeM.Materials and methods. The objects of the study were the original substance sodium 4,4'-(propanediamido)dibenzoate, as well as a number of auxiliary substances, which included polymers used for dosage forms with prolonged release, a dusting component – magnesium stearate, and a filler – lactose monohydrate. Physicochemical and technological properties of APIs, explosives, obtained tablet mixtures and tablets were studied in accordance with the requirements of the State Pharmacopoeia of the Russian Federation XIV ed. and EP 9th ed.Results and discussion. The properties of the substance and excipients were assessed in accordance with the SeDeM method. It was found that the substance 4,4'-(propanediamido) sodium dibenzoate is not suitable for direct pressing due to poor flowability and low compressibility. Hypromellose Methocel K4M had good compressibility, but it did not have sufficient flowability. The other tested polymers had satisfactory properties for the direct compression technology. The composition of the tablet mixtures was calculated using the SeDeM method, the obtained tablet mixtures had satisfactory technological characteristics for obtaining tablets by direct compression. The tablets obtained as a result of the experiment also met the pharmacopoeial requirements.Conclusion. Prediction of the composition of sustained-release tablets based on the original substance sodium 4,4'-(propanediamido)dibenzoate was carried out using the SeDeM method. It was found that this method is suitable for the development of the composition of tablets based on sodium 4,4'-(propanediamido)dibenzoate.