Alexey Abdrashitov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Alexey Abdrashitov has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Evgeny Alexandrovich Marfin
Institute of Power Engineering and Advanced Technologies, FRC Kazan Scientific Center, Russian Academy of Sciences, 420111 Kazan, Russia
11 shared publications - Denis V. Chachkov
Kazan Department of Joint Supercomputer Center of Russian Academy of Sciences–Branch of Federal Scientific Center “Scientific Research Institute for System Analysis of the RAS”, Lobachevskii Street 2/31, 420111 Kazan, Russia
3 shared publications - A.R. Galimzyanova
ФИЦ Казанский научный центр РАН
1 shared publication - Alexander Gavrilov
Department of Radio Electronics, Kazan Federal University, 420008 Kazan, Russia
1 shared publication - Andrey A. Kovalev
Federal State Budgetary Scientific Institution “Federal Scientific Agroengineering Center VIM”, 1st Institutskiy Proezd, 5, 109428 Moscow, Russia
1 shared publication E.A. Plakhova
Kazan Federal University
1 shared publication
Latest Publications
- 1 June 2026
- Published by Pleiades Publishing Ltd in Acoustical Physics
- Vol. 72 (3) , 333-342
The Strouhal Number in Jet Systems That Generate a Tone
The article presents the results of an experimental study of tone generation using nozzle–jet and nozzle–jet–orifice systems. The aim of the study is to refine the calculation of pressure fluctuation excitation in a jet-driven Helmholtz oscillator. The jet systems utilized cylindrical nozzles of varying relative lengths, as well as quarter-circle nozzles with an identically rounded inlet section along a circular arc, conjugate with a sharp-edged cylindrical outlet section. In the nozzle–jet system, a free air jet flowed unimpeded into a submerged space. In the nozzle–jet–orifice system, the free jet entered an orifice in a flat wall located at a certain distance from the nozzle exit. The average jet velocity was calculated from the pressure drop across the nozzle, and the amplitude and frequency of the generated pressure fluctuations were measured with a microphone. The ranges of relative nozzle lengths and Reynolds numbers within which a free jet generates a tone were determined. It is shown that in a system with a cylindrical nozzle, a tone occurs only at a certain duct length, and only a single harmonic is always observed in the spectrum. In a system with a profiled nozzle, no tone is observed in the absence of an obstacle. It is revealed that in the presence of a second plate with an orifice, the amplitude of pressure fluctuations increases significantly, and several harmonics are simultaneously present in the spectrum with a profiled nozzle. The validity of two theoretical models of jet tone generation is considered: Krüger’s model (for a nozzle–jet–orifice system with feedback) and Mordasov’s model (for a nozzle–jet system without feedback). For both jet systems, characteristic geometric dimensions are determined that ensure self-similarity in terms of the Strouhal number over a wide range of flow regime variations.
- 1 June 2026
- Published by Pleiades Publishing Ltd in Acoustical Physics
- Vol. 72 (3) , 333-342
The Strouhal Number in Jet Systems That Generate a Tone
The article presents the results of an experimental study of tone generation using nozzle–jet and nozzle–jet–orifice systems. The aim of the study is to refine the calculation of pressure fluctuation excitation in a jet-driven Helmholtz oscillator. The jet systems utilized cylindrical nozzles of varying relative lengths, as well as quarter-circle nozzles with an identically rounded inlet section along a circular arc, conjugate with a sharp-edged cylindrical outlet section. In the nozzle–jet system, a free air jet flowed unimpeded into a submerged space. In the nozzle–jet–orifice system, the free jet entered an orifice in a flat wall located at a certain distance from the nozzle exit. The average jet velocity was calculated from the pressure drop across the nozzle, and the amplitude and frequency of the generated pressure fluctuations were measured with a microphone. The ranges of relative nozzle lengths and Reynolds numbers within which a free jet generates a tone were determined. It is shown that in a system with a cylindrical nozzle, a tone occurs only at a certain duct length, and only a single harmonic is always observed in the spectrum. In a system with a profiled nozzle, no tone is observed in the absence of an obstacle. It is revealed that in the presence of a second plate with an orifice, the amplitude of pressure fluctuations increases significantly, and several harmonics are simultaneously present in the spectrum with a profiled nozzle. The validity of two theoretical models of jet tone generation is considered: Krüger’s model (for a nozzle–jet–orifice system with feedback) and Mordasov’s model (for a nozzle–jet system without feedback). For both jet systems, characteristic geometric dimensions are determined that ensure self-similarity in terms of the Strouhal number over a wide range of flow regime variations.
- 1 August 2023
- Published by Pleiades Publishing Ltd in Acoustical Physics
- Vol. 69 (4) , 471-477
Excitation of Acoustic Modes by Tone Harmonics of a Hole in a Jet-Driven Helmholtz Oscillator
Periodic pressure fluctuations were studied experimentally in the model of a jet-driven Helmholtz oscillator with a cylindrical chamber with a round air jet impinging on the sharp edge of the outlet. The evolution of the amplitude–frequency spectrum of the hole tone from its appearance at a jet velocity of about 2 m/s to excitation of the first acoustic resonance mode at the Helmholtz frequency was studied. The hole tone was a family of harmonics that progressively became more complex as the length and velocity of the jet increased. The successive occurrence of a family of acoustic modes on the harmonics of the jet tone with a further increase in jet velocity is studied. Modes at the Helmholtz frequency arose alternately on the harmonics of the hole tone in the gain band of the oscillator, starting from the highest harmonic. The first mode occurred at the highest harmonic; the second mode, at the previous harmonic; and so on. The final mode arose at the fundamental harmonic of the hole tone and had the maximum amplitude. With a further increase in the Reynolds number, periodic pressure fluctuations became disordered turbulent fluctuations. With a sufficient chamber size and jet velocity, azimuthal and half-wave resonances appeared at the highest harmonic of the hole tone. The largest Reynolds number at which resonance at the Helmholtz frequency was observed was 105.
- 1 August 2023
- Published by Pleiades Publishing Ltd in Acoustical Physics
- Vol. 69 (4) , 471-477
Excitation of Acoustic Modes by Tone Harmonics of a Hole in a Jet-Driven Helmholtz Oscillator
Periodic pressure fluctuations were studied experimentally in the model of a jet-driven Helmholtz oscillator with a cylindrical chamber with a round air jet impinging on the sharp edge of the outlet. The evolution of the amplitude–frequency spectrum of the hole tone from its appearance at a jet velocity of about 2 m/s to excitation of the first acoustic resonance mode at the Helmholtz frequency was studied. The hole tone was a family of harmonics that progressively became more complex as the length and velocity of the jet increased. The successive occurrence of a family of acoustic modes on the harmonics of the jet tone with a further increase in jet velocity is studied. Modes at the Helmholtz frequency arose alternately on the harmonics of the hole tone in the gain band of the oscillator, starting from the highest harmonic. The first mode occurred at the highest harmonic; the second mode, at the previous harmonic; and so on. The final mode arose at the fundamental harmonic of the hole tone and had the maximum amplitude. With a further increase in the Reynolds number, periodic pressure fluctuations became disordered turbulent fluctuations. With a sufficient chamber size and jet velocity, azimuthal and half-wave resonances appeared at the highest harmonic of the hole tone. The largest Reynolds number at which resonance at the Helmholtz frequency was observed was 105.
- Open Access
- 9 June 2023
- Published by MDPI AG in Agriculture
- Vol. 13 (6) , 1218
Cavitation Reactor for Pretreatment of Liquid Agricultural Waste
One of the most well-known methods of intensifying the process of anaerobic digestion is the pretreatment of raw materials. For the first time, the use of a jet-driven Helmholtz oscillator for biomass pretreatment is proposed. The design of the device is optimal for creating hydraulic cavitation; however, in this case, acoustic oscillations are generated in the system and resonance occurs. In this study, the optimal design of this device was determined for the subsequent design of a cavitation reactor. The diameter of the resonant chamber was varied in the range from 28.3 to 47.5 mm, and its length from 6 to 14 mm; in addition, the diameter of the outlet was changed from 6.1 to 6.3 mm. Based on the experimental data obtained, it was found that the optimal ratio of the length of the resonator chamber to the diameter of the inlet nozzle is 1.73, and the inner diameter of the resonator chamber to the diameter of the inlet nozzle corresponds to 5.5. Improving the technology of agricultural waste disposal will ensure their maximum involvement in economic circulation, reduce the consumption of traditional fuel and energy resources, and improve the technological and machine-building base, which makes it possible to produce competitive cavitation reactors.
- 9 June 2023
- Published by MDPI AG in Agriculture
- Vol. 13 (6) , 1218
Open AccessCavitation Reactor for Pretreatment of Liquid Agricultural Waste
One of the most well-known methods of intensifying the process of anaerobic digestion is the pretreatment of raw materials. For the first time, the use of a jet-driven Helmholtz oscillator for biomass pretreatment is proposed. The design of the device is optimal for creating hydraulic cavitation; however, in this case, acoustic oscillations are generated in the system and resonance occurs. In this study, the optimal design of this device was determined for the subsequent design of a cavitation reactor. The diameter of the resonant chamber was varied in the range from 28.3 to 47.5 mm, and its length from 6 to 14 mm; in addition, the diameter of the outlet was changed from 6.1 to 6.3 mm. Based on the experimental data obtained, it was found that the optimal ratio of the length of the resonator chamber to the diameter of the inlet nozzle is 1.73, and the inner diameter of the resonator chamber to the diameter of the inlet nozzle corresponds to 5.5. Improving the technology of agricultural waste disposal will ensure their maximum involvement in economic circulation, reduce the consumption of traditional fuel and energy resources, and improve the technological and machine-building base, which makes it possible to produce competitive cavitation reactors.
- 1 January 2022
- Published by Siberian Branch of Russian Academy of Sciences
- p. 130-131
NUMERICAL SIMULATION OF GAS-DYNAMICS IN A JET EMITTER WITH A SLIT CHAMBER
Marfin E.A., Abdrashitov A.A.//2022
- 1 January 2022
- Published by Siberian Branch of Russian Academy of Sciences
- p. 130-131
NUMERICAL SIMULATION OF GAS-DYNAMICS IN A JET EMITTER WITH A SLIT CHAMBER
Marfin E.A., Abdrashitov A.A.//2022
- 1 January 2021
- Published by EAGE Publications bv
- Vol. 2021 (1) , 1-8
Features of Acoustic Emission Caused by Gas Filtration Through Highly Permeable Porous Media
- 1 January 2021
- Published by EAGE Publications bv
- Vol. 2021 (1) , 1-8
Features of Acoustic Emission Caused by Gas Filtration Through Highly Permeable Porous Media
- Open Access
- 1 January 2021
- Published by Studio D - akustika s.r.o. in Akustika
- Vol. 39 (VOLUME 39) , 214-218
FEATURES OF SOUND GENERATION BY THE JET-DRIVEN HELMHOLTZ OSCILLATOR
Experimental studies the model of a jet-driven Helmholtz oscillator has been carried out. The oscillator is a cylindrical chamber, closed on the sides by two covers with inlet and outlet holes. The oscillator was excited by a stream of airflow. The influence of the geometric dimensions of the chamber and the openings in the covers on the amplitude of pressure fluctuations was studied and the optimal channel configuration was determined. Particular attention is paid to the study of the influence on the amplitude of pressure fluctuations of the shape and size of the nozzle - the hole in the front cover. There were measured the following processes: the pressure drop across the nozzle, to calculate the speed of the jet at the chamber entrance, and the parameters of pressure fluctuations in the chamber, to plot the amplitude-frequency spectra. There were made certain observations of a jet tone appearance and acoustic modes excitation at the natural frequency of the chamber-resonator with a smooth increase in the jet velocity. The relationship between the jet tone and the resonant in the chamber is noted. Recommendations for designing a Helmholtz jet oscillator are presented.
- 1 January 2021
- Published by Studio D - akustika s.r.o. in Akustika
- Vol. 39 (VOLUME 39) , 214-218
Open AccessFEATURES OF SOUND GENERATION BY THE JET-DRIVEN HELMHOLTZ OSCILLATOR
Experimental studies the model of a jet-driven Helmholtz oscillator has been carried out. The oscillator is a cylindrical chamber, closed on the sides by two covers with inlet and outlet holes. The oscillator was excited by a stream of airflow. The influence of the geometric dimensions of the chamber and the openings in the covers on the amplitude of pressure fluctuations was studied and the optimal channel configuration was determined. Particular attention is paid to the study of the influence on the amplitude of pressure fluctuations of the shape and size of the nozzle - the hole in the front cover. There were measured the following processes: the pressure drop across the nozzle, to calculate the speed of the jet at the chamber entrance, and the parameters of pressure fluctuations in the chamber, to plot the amplitude-frequency spectra. There were made certain observations of a jet tone appearance and acoustic modes excitation at the natural frequency of the chamber-resonator with a smooth increase in the jet velocity. The relationship between the jet tone and the resonant in the chamber is noted. Recommendations for designing a Helmholtz jet oscillator are presented.
- 1 January 2021
- Published by Pleiades Publishing Ltd in Fluid Dynamics
- Vol. 56 (1) , 142-151
Nozzle Length Effect on the Performance of the Jet-Driven Helmholtz Oscillator
The excitation of pressure fluctuations in a model jet-driven Helmholtz oscillator is experimentally investigated. An axisymmetric channel consisted of a cylindrical chamber with a nozzle in the front cover and an outlet opening in the back one. Optimal geometric dimensions of the chamber, nozzle, and outlet were chosen to achieve the greatest amplitude of the pressure fluctuations in the chamber. The nozzle length-to-diameter ratio ln/dn varied in the 0.77 ≤ ln/dn ≤ 4.17 range. The cylindrical chamber length Lch determining the air jet length ljet in the interval between the covers and Lch/dn = 0.5–3.5. The outlet opening diameter in the back cover dout varied within the limits dout/dn = 1–2.5. The optimal nozzle length ln/dn, the corresponding chamber length Lch/dn, and the outlet diameter dout/dn are determined. The air jet development within the nozzle and the formation of an inverse flow zone between the nozzle wall and the jet periphery and a chain of vortex structures in the mixing layer are considered. The generation of a jet tone of the opening on the frequency of the feedback in the jet and a family of acoustic modes on the resonance frequency with a smooth increase in the jet velocity from 0 to 70 m/s is studied.
- 1 January 2021
- Published by Pleiades Publishing Ltd in Fluid Dynamics
- Vol. 56 (1) , 142-151
Nozzle Length Effect on the Performance of the Jet-Driven Helmholtz Oscillator
The excitation of pressure fluctuations in a model jet-driven Helmholtz oscillator is experimentally investigated. An axisymmetric channel consisted of a cylindrical chamber with a nozzle in the front cover and an outlet opening in the back one. Optimal geometric dimensions of the chamber, nozzle, and outlet were chosen to achieve the greatest amplitude of the pressure fluctuations in the chamber. The nozzle length-to-diameter ratio ln/dn varied in the 0.77 ≤ ln/dn ≤ 4.17 range. The cylindrical chamber length Lch determining the air jet length ljet in the interval between the covers and Lch/dn = 0.5–3.5. The outlet opening diameter in the back cover dout varied within the limits dout/dn = 1–2.5. The optimal nozzle length ln/dn, the corresponding chamber length Lch/dn, and the outlet diameter dout/dn are determined. The air jet development within the nozzle and the formation of an inverse flow zone between the nozzle wall and the jet periphery and a chain of vortex structures in the mixing layer are considered. The generation of a jet tone of the opening on the frequency of the feedback in the jet and a family of acoustic modes on the resonance frequency with a smooth increase in the jet velocity from 0 to 70 m/s is studied.
- 1 July 2020
- Published by AIP Publishing in Physics of Fluids
- Vol. 32 (7) , 077103
Short cylindrical nozzles in a jet-driven Helmholtz oscillator
The present paper elaborates on the experimental study of jet-excited pressure fluctuations in a Helmholtz oscillator model with two openings in a cylindrical cavity. The length of the cylindrical nozzle in the front cover ℓN normalized by the nozzle diameter dN was ℓN/dN = 0.125, 0.33, 0.47, and 0.67. The diameter of the outlet opening in the back cover dOUT was in the range dOUT/dN = 1–2.5. The length of the cylindrical cavity LCH determined the jet length LJET in the spacing between the covers, LCH/dN = 0.5–3.5. The amplitude–frequency spectra were studied when the oscillator configuration was changed in the indicated intervals. From the generation amplitude, the best ratio of the sizes of the nozzle, chamber, and outlet was determined. The appearance of the jet tone of the hole and the alternation of acoustic modes were observed with a smooth increase in the Reynolds number to ∼8 · 104. The measurements showed very high amplitude of pressure fluctuations in an oscillator with a short nozzle and a short chamber at a significant jet velocity. A slight increase in the length of the chamber led to a rapid decrease in the generation amplitude. It is determined that the tone frequency is usually much lower than the resonance frequency in the chamber. Moreover, the tone frequency gradually increases with increasing jet velocity, while the resonance frequency remains unchanged, close to the natural frequency of the cavity chamber.
- 1 July 2020
- Published by AIP Publishing in Physics of Fluids
- Vol. 32 (7) , 077103
Short cylindrical nozzles in a jet-driven Helmholtz oscillator
The present paper elaborates on the experimental study of jet-excited pressure fluctuations in a Helmholtz oscillator model with two openings in a cylindrical cavity. The length of the cylindrical nozzle in the front cover ℓN normalized by the nozzle diameter dN was ℓN/dN = 0.125, 0.33, 0.47, and 0.67. The diameter of the outlet opening in the back cover dOUT was in the range dOUT/dN = 1–2.5. The length of the cylindrical cavity LCH determined the jet length LJET in the spacing between the covers, LCH/dN = 0.5–3.5. The amplitude–frequency spectra were studied when the oscillator configuration was changed in the indicated intervals. From the generation amplitude, the best ratio of the sizes of the nozzle, chamber, and outlet was determined. The appearance of the jet tone of the hole and the alternation of acoustic modes were observed with a smooth increase in the Reynolds number to ∼8 · 104. The measurements showed very high amplitude of pressure fluctuations in an oscillator with a short nozzle and a short chamber at a significant jet velocity. A slight increase in the length of the chamber led to a rapid decrease in the generation amplitude. It is determined that the tone frequency is usually much lower than the resonance frequency in the chamber. Moreover, the tone frequency gradually increases with increasing jet velocity, while the resonance frequency remains unchanged, close to the natural frequency of the cavity chamber.
- 1 January 2019
- Published by EAGE Publications bv
- Vol. 2019 (1) , 1-5
Numerical Simulation of Non-Stationary Fluid Filtration in a Digital Model of a Synthetic Porous Medium
- 1 January 2019
- Published by EAGE Publications bv
- Vol. 2019 (1) , 1-5
Numerical Simulation of Non-Stationary Fluid Filtration in a Digital Model of a Synthetic Porous Medium
- 20 July 2018
- Published by Pleiades Publishing Ltd in Acoustical Physics
- Vol. 64 (4) , 492-502
Effect of Nozzle Shape on Amplitude of Well Acoustic Emitter Generation
An experimental study of the generation of pressure fluctuations in a well acoustic emitter with nozzles of various shapes has been carried out. The effect of a smooth nozzle inlet section on the...
- 20 July 2018
- Published by Pleiades Publishing Ltd in Acoustical Physics
- Vol. 64 (4) , 492-502
Effect of Nozzle Shape on Amplitude of Well Acoustic Emitter Generation
An experimental study of the generation of pressure fluctuations in a well acoustic emitter with nozzles of various shapes has been carried out. The effect of a smooth nozzle inlet section on the...