Si-Huy Ngo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Si-Huy Ngo has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Trong-Phuoc Huynh
Can Tho University
5 shared publications - Van-Dung Nguyen
Hong Duc University
4 shared publications - Tri Ho Minh Le
Nguyen Tat Thanh University
3 shared publications Huynh Trong-Phuoc
Department of Rural Technology, College of Rural Development, Can Tho University, Campus II, Can Tho City, Viet Nam
1 shared publicationLe Thi Thanh-Tam
Department of Engineering and Technology, Hong Duc University, Thanh Hoa City, Viet Nam
1 shared publicationNgoc-Hang Thi Mai
Department of Engineering and Technology, Hong Duc University, No. 565, Quang Trung Street, Dong Ve Ward, Thanh Hoa City 440000, Vietnam
1 shared publication
Latest Publications
- Open Access
- 9 July 2026
- Published by IOP Publishing in Materials Research Express
- Vol. 13 (13) , 135501
Potential use of binary fly ash-ground granulated blast furnace slag mixtures as precursors in low-carbon sulfate-activated composites
This study investigates the feasibility of using binary fly ash (FA) and ground granulated blast-furnace slag (GGBFS) mixtures as precursors for low-carbon sulfate-activated composites activated with sodium sulfate. The FA/GGBFS ratio was systematically varied to clarify its influence on fresh properties, strength development, durability-related indicators, microstructural characteristics, and sustainability performance. The results show that increasing FA content improved flowability but significantly prolonged both initial and final setting times. In terms of physical performance, FA incorporation up to 15% promoted matrix refinement, as reflected by reduced porosity and water absorption, while higher replacement levels led to less consistent improvement. Mechanical test results indicated that the mixture containing 15% FA (F15S85) provided the most balanced strength development within the investigated range, achieving the highest flexural strength (3.94 MPa) and compressive strength (55.14 MPa) at 56 d. Drying shrinkage decreased progressively with increasing FA content, with the 20% FA mixture showing the lowest shrinkage, whereas F15S85 offered a more favorable balance between strength and dimensional stability. Ultrasonic pulse velocity and rapid chloride ion penetration test results further confirmed that moderate FA incorporation improved matrix compactness and resistance to chloride ingress. Scanning electron microscopy observations showed a denser and more homogeneous matrix in mixtures containing 10%–15% FA, while x-ray diffraction patterns qualitatively indicated changes in crystalline phase characteristics with increasing FA replacement. From a sustainability perspective, increasing FA content reduced both material cost and CO 2 -equivalent emissions, with F20S80 showing the greatest economic and environmental benefit. Overall, the results indicate that partial replacement of GGBFS by FA can improve the balance between performance and sustainability in sulfate-activated systems. Within the investigated range, F15S85 showed the most favorable mechanical performance and matrix compactness, whereas F20S80 provided greater benefits in shrinkage reduction, material cost, and CO 2 -eq efficiency.
- 9 July 2026
- Published by IOP Publishing in Materials Research Express
- Vol. 13 (13) , 135501
Open AccessPotential use of binary fly ash-ground granulated blast furnace slag mixtures as precursors in low-carbon sulfate-activated composites
This study investigates the feasibility of using binary fly ash (FA) and ground granulated blast-furnace slag (GGBFS) mixtures as precursors for low-carbon sulfate-activated composites activated with sodium sulfate. The FA/GGBFS ratio was systematically varied to clarify its influence on fresh properties, strength development, durability-related indicators, microstructural characteristics, and sustainability performance. The results show that increasing FA content improved flowability but significantly prolonged both initial and final setting times. In terms of physical performance, FA incorporation up to 15% promoted matrix refinement, as reflected by reduced porosity and water absorption, while higher replacement levels led to less consistent improvement. Mechanical test results indicated that the mixture containing 15% FA (F15S85) provided the most balanced strength development within the investigated range, achieving the highest flexural strength (3.94 MPa) and compressive strength (55.14 MPa) at 56 d. Drying shrinkage decreased progressively with increasing FA content, with the 20% FA mixture showing the lowest shrinkage, whereas F15S85 offered a more favorable balance between strength and dimensional stability. Ultrasonic pulse velocity and rapid chloride ion penetration test results further confirmed that moderate FA incorporation improved matrix compactness and resistance to chloride ingress. Scanning electron microscopy observations showed a denser and more homogeneous matrix in mixtures containing 10%–15% FA, while x-ray diffraction patterns qualitatively indicated changes in crystalline phase characteristics with increasing FA replacement. From a sustainability perspective, increasing FA content reduced both material cost and CO 2 -equivalent emissions, with F20S80 showing the greatest economic and environmental benefit. Overall, the results indicate that partial replacement of GGBFS by FA can improve the balance between performance and sustainability in sulfate-activated systems. Within the investigated range, F15S85 showed the most favorable mechanical performance and matrix compactness, whereas F20S80 provided greater benefits in shrinkage reduction, material cost, and CO 2 -eq efficiency.
- Open Access
- 25 May 2026
- Published by Elsevier in Next Materials
- Vol. 12
Impact resistance and low-carbon potential of concrete using rubber from scrap tires
- 25 May 2026
- Published by Elsevier in Next Materials
- Vol. 12
Open AccessImpact resistance and low-carbon potential of concrete using rubber from scrap tires
- Open Access
- 1 May 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (10) , 105109
Towards eco-efficient mortars: influence of fly ash fineness and content on strength, durability, and microstructural behavior
Global net-zero commitments are accelerating the transition toward low-clinker, high-performance binders. This study systematically investigates the combined effects of fly ash (FA) fineness and replacement level on the mechanical performance, transport resistance, and hydration stability of eco-efficient mortars incorporating ground granulated blast-furnace slag. Three FA fineness levels—Fa1 (277.2 m 2 kg −1 ), Fa2 (299.6 m 2 kg −1 ), and Fa3 (313.5 m 2 kg −1 )—were evaluated at 10%–40% cement replacement. Compressive strength, porosity, water absorption, rapid chloride penetration, scanning electron microscopy, x-ray diffraction, Fourier transform infrared spectroscopy, and thermogravimetric analysis were integrated to establish microstructure–performance relationships. Although increasing FA content reduced 28 d strength by 1.2%–29.8%, FA-modified mixtures exhibited significantly greater long-term strength gains (25%–64%) than the control (17%). At 30% replacement, fineness became decisive: Fa3-30 achieved 94.93 MPa at 180 d, with 5.87% porosity, 2.34% water absorption, and 779 Coulombs. Regression analysis identified porosity as the primary structural control parameter, with each 1% increase corresponding to an 8.9 MPa strength reduction and a 243 Coulombs increase. Thermogravimetric and spectroscopic evidence indicate that finer FA enhances gel polymerization, stabilizes bound water, and promotes hydrate network maturation. Within the investigated compositional domain, 30% ultrafine FA provides the most favorable balance among mechanical performance, pore refinement, transport resistance, and clinker reduction efficiency.
- 1 May 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (10) , 105109
Open AccessTowards eco-efficient mortars: influence of fly ash fineness and content on strength, durability, and microstructural behavior
Global net-zero commitments are accelerating the transition toward low-clinker, high-performance binders. This study systematically investigates the combined effects of fly ash (FA) fineness and replacement level on the mechanical performance, transport resistance, and hydration stability of eco-efficient mortars incorporating ground granulated blast-furnace slag. Three FA fineness levels—Fa1 (277.2 m 2 kg −1 ), Fa2 (299.6 m 2 kg −1 ), and Fa3 (313.5 m 2 kg −1 )—were evaluated at 10%–40% cement replacement. Compressive strength, porosity, water absorption, rapid chloride penetration, scanning electron microscopy, x-ray diffraction, Fourier transform infrared spectroscopy, and thermogravimetric analysis were integrated to establish microstructure–performance relationships. Although increasing FA content reduced 28 d strength by 1.2%–29.8%, FA-modified mixtures exhibited significantly greater long-term strength gains (25%–64%) than the control (17%). At 30% replacement, fineness became decisive: Fa3-30 achieved 94.93 MPa at 180 d, with 5.87% porosity, 2.34% water absorption, and 779 Coulombs. Regression analysis identified porosity as the primary structural control parameter, with each 1% increase corresponding to an 8.9 MPa strength reduction and a 243 Coulombs increase. Thermogravimetric and spectroscopic evidence indicate that finer FA enhances gel polymerization, stabilizes bound water, and promotes hydrate network maturation. Within the investigated compositional domain, 30% ultrafine FA provides the most favorable balance among mechanical performance, pore refinement, transport resistance, and clinker reduction efficiency.
- Open Access
- 25 March 2026
- Published by IOP Publishing in Materials Research Express
- Vol. 13 (6) , 065504
Development and characterization of eco-friendly cement-free composites activated by different sulfate-activators
Portland cement production accounts for nearly 8% of global CO 2 emissions, driving the search for sustainable alternatives. In this study, ground granulated blast-furnace slag (GGBFS) was chemically activated with four sulfate activators (Na 2 SO 4 , K 2 SO 4 , MgSO 4 , and CaSO 4 ) to produce cement-free composites (CFC). Prior research has primarily focused on individual sulfate activators, whereas direct comparison under standardized mixture conditions remains limited. Accordingly, this study was designed to systematically evaluate the influence of different sulfate-associated cations on hydration behavior, mechanical performance, and durability-related properties using a fixed mixture design (water-to-binder = 0.30 and activator dosage = 4.5% by mass of GGBFS). A series of fresh, mechanical, transport-related, and volumetric tests was conducted, complemented by scanning electron microscopy (SEM) and x-ray diffraction (XRD) analyses at 28 days to examine microstructural development. Rather than enumerating individual test results, the comparative analysis reveals clear performance trends governed by activator chemistry. CaSO 4 activation consistently promotes matrix densification and strength development, while MgSO 4 markedly suppresses drying shrinkage due to inhibited GGBFS dissolution. Sodium and potassium sulfates exhibit intermediate behavior, balancing workability, strength evolution, and durability-related indicators. The systematic comparative analysis conducted in this study identified CaSO 4 as the most effective activator among those investigated for eco-friendly cement-free composites. These findings demonstrate that sulfate activation can be effectively tailored through cation selection, offering a practical and safer pathway for the design of one-part, low-carbon GGBFS-based binders suitable for construction applications.
- 25 March 2026
- Published by IOP Publishing in Materials Research Express
- Vol. 13 (6) , 065504
Open AccessDevelopment and characterization of eco-friendly cement-free composites activated by different sulfate-activators
Portland cement production accounts for nearly 8% of global CO 2 emissions, driving the search for sustainable alternatives. In this study, ground granulated blast-furnace slag (GGBFS) was chemically activated with four sulfate activators (Na 2 SO 4 , K 2 SO 4 , MgSO 4 , and CaSO 4 ) to produce cement-free composites (CFC). Prior research has primarily focused on individual sulfate activators, whereas direct comparison under standardized mixture conditions remains limited. Accordingly, this study was designed to systematically evaluate the influence of different sulfate-associated cations on hydration behavior, mechanical performance, and durability-related properties using a fixed mixture design (water-to-binder = 0.30 and activator dosage = 4.5% by mass of GGBFS). A series of fresh, mechanical, transport-related, and volumetric tests was conducted, complemented by scanning electron microscopy (SEM) and x-ray diffraction (XRD) analyses at 28 days to examine microstructural development. Rather than enumerating individual test results, the comparative analysis reveals clear performance trends governed by activator chemistry. CaSO 4 activation consistently promotes matrix densification and strength development, while MgSO 4 markedly suppresses drying shrinkage due to inhibited GGBFS dissolution. Sodium and potassium sulfates exhibit intermediate behavior, balancing workability, strength evolution, and durability-related indicators. The systematic comparative analysis conducted in this study identified CaSO 4 as the most effective activator among those investigated for eco-friendly cement-free composites. These findings demonstrate that sulfate activation can be effectively tailored through cation selection, offering a practical and safer pathway for the design of one-part, low-carbon GGBFS-based binders suitable for construction applications.
- Open Access
- 15 November 2024
- Published by Hong Duc University in Tạp chí Khoa học Trường Đại học Hồng Đức
- Vol. 2 (tháng 11) , 39-46
ẢNH HƯỞNG CỦA HÀM LƯỢNG TRO BAY LÊN CÁC ĐẶC TÍNH CƠ LÝ VÀ VI CẤU TRÚC CỦA VỮA CƯỜNG ĐỘ CAO
Quá trình sản xuất xi măng thải ra một lượng lớn khí CO2 làm cho trái đất nóng lên, trong khi đó các nhà máy nhiệt điện hàng ngày cũng thải ra một lượng lớn tro bay. Bài báo nghiên cứu sử dụng tro bay để thay thế một phần xi măng trong sản xuất vữa cường độ cao. Ảnh hưởng của hàm lượng tro bay lên các đặc tính cơ lý và vi cấu trúc của vữa được nghiên cứu. Kết quả thí nghiệm chỉ ra rằng, mặc dù cường độ chịu nén và vận tốc truyền xung siêu âm của các mẫu vữa giảm khi tăng hàm lượng tro bay, tuy nhiên các mẫu vữa vẫn đạt cường độ chịu nén lớn hơn 50 MPa và giá trị vận tốc truyền xung siêu âm lớn hơn 4100 m/s. Tất cả các mẫu vữa đều có khả năng chống lại sự thẩm thấu của các ion Clo tương đối tốt. Kết quả nghiên cứu cho thấy có thể sử dụng tro bay của nhà máy nhiệt điện Nghi Sơn 1 để thay thế một phần xi măng trong sản xuất vữa xây dựng có chất lượng cao.
- 15 November 2024
- Published by Hong Duc University in Tạp chí Khoa học Trường Đại học Hồng Đức
- Vol. 2 (tháng 11) , 39-46
Open AccessẢNH HƯỞNG CỦA HÀM LƯỢNG TRO BAY LÊN CÁC ĐẶC TÍNH CƠ LÝ VÀ VI CẤU TRÚC CỦA VỮA CƯỜNG ĐỘ CAO
Quá trình sản xuất xi măng thải ra một lượng lớn khí CO2 làm cho trái đất nóng lên, trong khi đó các nhà máy nhiệt điện hàng ngày cũng thải ra một lượng lớn tro bay. Bài báo nghiên cứu sử dụng tro bay để thay thế một phần xi măng trong sản xuất vữa cường độ cao. Ảnh hưởng của hàm lượng tro bay lên các đặc tính cơ lý và vi cấu trúc của vữa được nghiên cứu. Kết quả thí nghiệm chỉ ra rằng, mặc dù cường độ chịu nén và vận tốc truyền xung siêu âm của các mẫu vữa giảm khi tăng hàm lượng tro bay, tuy nhiên các mẫu vữa vẫn đạt cường độ chịu nén lớn hơn 50 MPa và giá trị vận tốc truyền xung siêu âm lớn hơn 4100 m/s. Tất cả các mẫu vữa đều có khả năng chống lại sự thẩm thấu của các ion Clo tương đối tốt. Kết quả nghiên cứu cho thấy có thể sử dụng tro bay của nhà máy nhiệt điện Nghi Sơn 1 để thay thế một phần xi măng trong sản xuất vữa xây dựng có chất lượng cao.
- Open Access
- 4 May 2024
- Published by Can Tho University in CTU Journal of Innovation and Sustainable Development
- Vol. 16 (Special : ) , 1-7
Utilizing coal combustion bottom ash as a sustainable alternative to natural aggregate in eco-friendly building bricks
As a substitute for fried clay and stone powder-cement bricks, this study developed novel green bricks based on coal-combustion bottom ash (CCBA) obtained from a thermal power plant in Vietnam. By using varied replacement amounts of stone powder at 0, 10, 20, 30, and 40% in weight, ten brick compositions with water-to-binder (w/b) ratios of 0.35 and 0.40 were developed. Testing was done on the bricks' characteristics, such as compressive strength, ultrasonic pulse velocity, water absorption, water permeability, electrical resistance, and thermal conductivity. The findings showed that increasing CCBA content or w/b ratio has a negative impact on the characteristics of unburnt bricks. However, all the brick samples made for this investigation performed exceptionally well when compared to the requirements of the national Vietnamese standard. The brick samples produced in this study are recommended to apply in real practice.
- 4 May 2024
- Published by Can Tho University in CTU Journal of Innovation and Sustainable Development
- Vol. 16 (Special : ) , 1-7
Open AccessUtilizing coal combustion bottom ash as a sustainable alternative to natural aggregate in eco-friendly building bricks
As a substitute for fried clay and stone powder-cement bricks, this study developed novel green bricks based on coal-combustion bottom ash (CCBA) obtained from a thermal power plant in Vietnam. By using varied replacement amounts of stone powder at 0, 10, 20, 30, and 40% in weight, ten brick compositions with water-to-binder (w/b) ratios of 0.35 and 0.40 were developed. Testing was done on the bricks' characteristics, such as compressive strength, ultrasonic pulse velocity, water absorption, water permeability, electrical resistance, and thermal conductivity. The findings showed that increasing CCBA content or w/b ratio has a negative impact on the characteristics of unburnt bricks. However, all the brick samples made for this investigation performed exceptionally well when compared to the requirements of the national Vietnamese standard. The brick samples produced in this study are recommended to apply in real practice.
- 1 March 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 148 (3) , 04021303
Shear Strength Model for Reinforced Concrete Bridge Columns with Multispiral Transverse Reinforcement
A shear strength model is proposed for reinforced concrete bridge columns with multispiral transverse reinforcement. The proposed model consists of a proposed discrete computational shear strength model for multispiral reinforcement and shear strength models for concrete and axial load adopted from the literature. The proposed discrete computational model calculates shear strength from each discrete location of the interception between the shear crack and multispiral reinforcement. Furthermore, the model considers the critical location of the shear crack, shear crack angle, direction of shear, and effect of the compression zone. The proposed model together with the Caltrans SDC model, Sezen’s model, and Priestley’s model are used to predict the shear strength of multispiral columns tested in the literature. Comparison between the prediction and test result shows that the proposed shear strength model produces the best prediction in terms of the mean and standard deviation of the ratio of experimental to predicted shear strength. Based on analysis and test observations, equations to estimate the compression depth of multispiral columns at the ultimate condition and the shear crack angle are proposed to be used in the proposed discrete computational shear strength model.
- 1 March 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 148 (3) , 04021303
Shear Strength Model for Reinforced Concrete Bridge Columns with Multispiral Transverse Reinforcement
A shear strength model is proposed for reinforced concrete bridge columns with multispiral transverse reinforcement. The proposed model consists of a proposed discrete computational shear strength model for multispiral reinforcement and shear strength models for concrete and axial load adopted from the literature. The proposed discrete computational model calculates shear strength from each discrete location of the interception between the shear crack and multispiral reinforcement. Furthermore, the model considers the critical location of the shear crack, shear crack angle, direction of shear, and effect of the compression zone. The proposed model together with the Caltrans SDC model, Sezen’s model, and Priestley’s model are used to predict the shear strength of multispiral columns tested in the literature. Comparison between the prediction and test result shows that the proposed shear strength model produces the best prediction in terms of the mean and standard deviation of the ratio of experimental to predicted shear strength. Based on analysis and test observations, equations to estimate the compression depth of multispiral columns at the ultimate condition and the shear crack angle are proposed to be used in the proposed discrete computational shear strength model.
- 1 February 2020
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 35 (1) , 131-139
Effects of NaOH Concentrations on Properties of the Thermal Power Plant Ashes-Bricks by Alkaline Activation
- 1 February 2020
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 35 (1) , 131-139
Effects of NaOH Concentrations on Properties of the Thermal Power Plant Ashes-Bricks by Alkaline Activation
- Open Access
- 19 June 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 371 (1) , 012007
Effect of High Loss on Ignition-Fly Ash on Properties of Concrete Fully Immersed in Sulfate Solution
This paper presents the experimental results of an investigation on the engineering properties and durability of high loss on ignition-fly ash concrete fully immersed in 5% sodium sulfate solution. The fly ash used in this study is a raw material with the loss on ignition of 15.8%, which is much higher than the upper limitation of 6% as stipulated by ASTM C618. Eight concrete mixtures were designed with different water-to-binder ratios of 0.35 and 0.45. For each water-to-binder ratio, the fly ash was used to replace 0%, 10%, 20%, and 30% amount of cement. Test results show that the workability of fresh concrete increased, while its unit weight decreased with increasing the fly ash replacement level. In addition, the concrete mixtures with 10% and 20% fly ash content showed the higher compressive strength, especially at long-term ages, than that of the fly ash-free concrete mixture. Further, all of the fly ash concrete mixtures exhibited the good quality with ultrasonic pulse velocity values of higher than 4100 m/s.
- 19 June 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 371 (1) , 012007
Open AccessEffect of High Loss on Ignition-Fly Ash on Properties of Concrete Fully Immersed in Sulfate Solution
This paper presents the experimental results of an investigation on the engineering properties and durability of high loss on ignition-fly ash concrete fully immersed in 5% sodium sulfate solution. The fly ash used in this study is a raw material with the loss on ignition of 15.8%, which is much higher than the upper limitation of 6% as stipulated by ASTM C618. Eight concrete mixtures were designed with different water-to-binder ratios of 0.35 and 0.45. For each water-to-binder ratio, the fly ash was used to replace 0%, 10%, 20%, and 30% amount of cement. Test results show that the workability of fresh concrete increased, while its unit weight decreased with increasing the fly ash replacement level. In addition, the concrete mixtures with 10% and 20% fly ash content showed the higher compressive strength, especially at long-term ages, than that of the fly ash-free concrete mixture. Further, all of the fly ash concrete mixtures exhibited the good quality with ultrasonic pulse velocity values of higher than 4100 m/s.