Joshua Silverstein
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Joshua Silverstein has a total of 85 co-authors. Here are the top co-authors by number of shared publications:
- Bharat Gwalani
Department of Materials Science and Engineering, North Carolina State University, Raleigh, USA
6 shared publications - Julian D. Escobar
Pacific Northwest National Laboratory, Richland, USA
5 shared publications - Suveen Mathaudhu
Colorado School of Mines
4 shared publications Arun Devaraj
3 shared publications- Anqi Yu
Government of the United States of America - Pacific Northwest National Laboratory
2 shared publications - Arun Devaraj
Physical and Computational Sciences Directorate, Pacific Northwest National Laboratory, Richland, USA
2 shared publications
Latest Publications
- Open Access
- 23 June 2026
- Published by Elsevier in SSRN Electronic Journal
Defect Evolution and Microstructural Response of C-Ion Irradiated 304L Stainless Steel from 30–850°C
Austenitic 304L stainless steel was irradiated with 5 MeV C ions to selected doses of 10 and 100 dpa at temperatures between 30 and 850 °C to examine how irradiation temperature influences defect evolution, microstructural changes, and mechanical response. At 30 °C and 100 dpa, irradiation produced dense defect populations, including dislocation loops and a carbon-rich damaged region near the calculated damage peak, accompanied by measurable irradiation hardening. At 500 °C and 100 dpa, increased defect mobility promoted void formation and Ni–Si segregation to irradiation-induced defect structures, with positron annihilation measurements indicating an increased contribution from vacancy-type defects. At 850 °C, thermal recovery and high-temperature microstructural reorganization reduced the net hardening response and were accompanied by carbide and sulfide precipitation. XRD and EBSD confirmed that the microstructure retained a primarily FCC austenitic matrix with a minor BCC/martensitic phase, whose measured fraction varied with irradiation condition. Overall, these results show that C-ion irradiation of 304L stainless steel produces distinct defect and microstructural responses depending on irradiation temperature, with low-temperature defect accumulation, intermediate-temperature void formation and segregation, and high-temperature recovery and precipitation all contributing to the observed mechanical behavior.
- 23 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessDefect Evolution and Microstructural Response of C-Ion Irradiated 304L Stainless Steel from 30–850°C
Austenitic 304L stainless steel was irradiated with 5 MeV C ions to selected doses of 10 and 100 dpa at temperatures between 30 and 850 °C to examine how irradiation temperature influences defect evolution, microstructural changes, and mechanical response. At 30 °C and 100 dpa, irradiation produced dense defect populations, including dislocation loops and a carbon-rich damaged region near the calculated damage peak, accompanied by measurable irradiation hardening. At 500 °C and 100 dpa, increased defect mobility promoted void formation and Ni–Si segregation to irradiation-induced defect structures, with positron annihilation measurements indicating an increased contribution from vacancy-type defects. At 850 °C, thermal recovery and high-temperature microstructural reorganization reduced the net hardening response and were accompanied by carbide and sulfide precipitation. XRD and EBSD confirmed that the microstructure retained a primarily FCC austenitic matrix with a minor BCC/martensitic phase, whose measured fraction varied with irradiation condition. Overall, these results show that C-ion irradiation of 304L stainless steel produces distinct defect and microstructural responses depending on irradiation temperature, with low-temperature defect accumulation, intermediate-temperature void formation and segregation, and high-temperature recovery and precipitation all contributing to the observed mechanical behavior.
- 22 July 2025
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 616
In-situ temperature-dependent evaluation of phase makeup and gas evolution of hydrogen-loaded Ni-plated Zircaloy-4
- 22 July 2025
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 616
In-situ temperature-dependent evaluation of phase makeup and gas evolution of hydrogen-loaded Ni-plated Zircaloy-4
- Open Access
- 9 December 2023
- Published by Elsevier in Materials & Design
- Vol. 237
Unprecedented electrical performance of friction-extruded copper-graphene composites
- 9 December 2023
- Published by Elsevier in Materials & Design
- Vol. 237
Open AccessUnprecedented electrical performance of friction-extruded copper-graphene composites
- 16 September 2023
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 886
Microstructural evolution in shear-punch tests: A comparative study of pure Cu and Cu-Cr alloy
- 16 September 2023
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 886
Microstructural evolution in shear-punch tests: A comparative study of pure Cu and Cu-Cr alloy
- Open Access
- 6 January 2023
- Published by Elsevier in SSRN Electronic Journal
Shear Localization in Single-Phase Cu and Cu/Nb Nanolaminates Using Micromechanical Framework
Material processing by shear deformation can result in unique microstructural evolution pathways and often enhanced mechanical properties, especially for immiscible systems such as Cu/Nb. To establish the correlation between deformation and microstructural evolution during shear, a mechanistic understanding of stress localization is needed. In this study, a specific Sshaped specimen geometry is implemented to apply localized simple-shear loading in pure-Cu and Cu/Nb accumulative roll-bonded nanolaminates. The refined grain-structure and proximity of interfaces in Cu/Nb offered a ~2.8-fold increase in shear stresses than pure-Cu. In pure-Cu, the plastic instability causes shear banding and an in-plane lattice rotation while in Cu/Nb, a partial bending of the interfaces occurred resulting in a localized lattice rotation. Our geometry for micro-scale specimens captures the shear deformation at predetermined sites in two distinct material systems and could potentially be a powerful technique to study the deformation mechanisms.
- 6 January 2023
- Published by Elsevier in SSRN Electronic Journal
Open AccessShear Localization in Single-Phase Cu and Cu/Nb Nanolaminates Using Micromechanical Framework
Material processing by shear deformation can result in unique microstructural evolution pathways and often enhanced mechanical properties, especially for immiscible systems such as Cu/Nb. To establish the correlation between deformation and microstructural evolution during shear, a mechanistic understanding of stress localization is needed. In this study, a specific Sshaped specimen geometry is implemented to apply localized simple-shear loading in pure-Cu and Cu/Nb accumulative roll-bonded nanolaminates. The refined grain-structure and proximity of interfaces in Cu/Nb offered a ~2.8-fold increase in shear stresses than pure-Cu. In pure-Cu, the plastic instability causes shear banding and an in-plane lattice rotation while in Cu/Nb, a partial bending of the interfaces occurred resulting in a localized lattice rotation. Our geometry for micro-scale specimens captures the shear deformation at predetermined sites in two distinct material systems and could potentially be a powerful technique to study the deformation mechanisms.
- 22 March 2022
- Published by Elsevier in Materialia
- Vol. 22
Decoupling of strain and temperature effects on microstructural evolution during high shear strain deformation
- 22 March 2022
- Published by Elsevier in Materialia
- Vol. 22
Decoupling of strain and temperature effects on microstructural evolution during high shear strain deformation
- 1 February 2022
- Published by Elsevier in Journal of Environmental Radioactivity
- Vol. 244-245, 106824
The behavior of iodine in stabilized granular activated carbon and silver mordenite in cementitious waste forms
- 1 February 2022
- Published by Elsevier in Journal of Environmental Radioactivity
- Vol. 244-245, 106824
The behavior of iodine in stabilized granular activated carbon and silver mordenite in cementitious waste forms
- Open Access
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Heterogenous Activation of Dynamic Recrystallization and Twinning During Friction Stir Processing of a Cu-4Nb Alloy
An interplay between high degree of shear deformation and deformation-induced heating occurs during friction stir processing (FSP) of metals. In medium-to-low stacking fault energy Cu alloys, this can lead to a complex spatially heterogenous activation of dynamic recrystallization (DRX) and twinning mechanisms. Within the Cu-Nb system, the presence of Nb is further expected to influence the DRX mechanism of the Cu matrix. However, the microstructural changes induced by the co-deformation of Nb during FSP are still not well understood. Therefore, this study using a combination of multimodal microstructural characterization, solution thermodynamics based predictions, and computational crystal plasticity simulation focuses on revealing the various microstructrural evolution mechanisms that can occur during FSP of a Cu-4at.%Nb binary model alloy. The formation of softer DRX zones, and harder shear localization regions are revealed using electron backscatter diffraction, transmission electron microscopy, atom probe tomography, and crystal plasticity modeling.
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Open AccessHeterogenous Activation of Dynamic Recrystallization and Twinning During Friction Stir Processing of a Cu-4Nb Alloy
An interplay between high degree of shear deformation and deformation-induced heating occurs during friction stir processing (FSP) of metals. In medium-to-low stacking fault energy Cu alloys, this can lead to a complex spatially heterogenous activation of dynamic recrystallization (DRX) and twinning mechanisms. Within the Cu-Nb system, the presence of Nb is further expected to influence the DRX mechanism of the Cu matrix. However, the microstructural changes induced by the co-deformation of Nb during FSP are still not well understood. Therefore, this study using a combination of multimodal microstructural characterization, solution thermodynamics based predictions, and computational crystal plasticity simulation focuses on revealing the various microstructrural evolution mechanisms that can occur during FSP of a Cu-4at.%Nb binary model alloy. The formation of softer DRX zones, and harder shear localization regions are revealed using electron backscatter diffraction, transmission electron microscopy, atom probe tomography, and crystal plasticity modeling.
- Open Access
- 1 January 2022
- Published by Elsevier in Materials & Design
- Vol. 213
Extrusion of Unhomogenized Castings of 7075 Aluminum via ShAPE
- 1 January 2022
- Published by Elsevier in Materials & Design
- Vol. 213
Open AccessExtrusion of Unhomogenized Castings of 7075 Aluminum via ShAPE
- Open Access
- 1 January 2022
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 10 (1) , 110-118
Friction-based riveting technique for AZ31 magnesium alloy
- 1 January 2022
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 10 (1) , 110-118
Open AccessFriction-based riveting technique for AZ31 magnesium alloy