Magdalena Baran
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Magdalena Baran has a total of 54 co-authors. Here are the top co-authors by number of shared publications:
- Tomasz Strachowski
Polish Academy of Sciences
6 shared publications - Adrian Chlanda
Department of Functional Materials, Łukasiewicz Research Network—Institute of Microelectronics and Photonics, Lotników 32, 02-668 Warsaw, Poland
4 shared publications - Agata Romanowska
Ukasiewicz Research Network Institute of Microelectronics and Photonics, Flake Graphene Research Group, Warsaw, Poland
4 shared publications - Ewa Grzanka
Institute of High Pressure Physics
3 shared publications - Jan Mizeracki
Institute of High Pressure Physics PAS “Unipress”, Sokolowska 29/37, 01-142 Warsaw, Poland
3 shared publications - Marcin Małek
Institute of Civil Engineering, Faculty of Civil Engineering and Geodesy, Military University of Technology, 00-908 Warsaw, Poland
3 shared publications
Latest Publications
- 4 May 2025
- Published by Elsevier in Materials Today Communications
- Vol. 46
Thermal reduction of graphene oxide via high-temperature annealing in a CH4 and CO reducing atmosphere
- 4 May 2025
- Published by Elsevier in Materials Today Communications
- Vol. 46
Thermal reduction of graphene oxide via high-temperature annealing in a CH4 and CO reducing atmosphere
- 4 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nanotechnology
- Vol. 23 (1536125X) , 329-337
Graphene Oxide Paper as a Lightweight, Thin, and Controllable Microwave Absorber for Millimeter-Wave Applications
The production and verification of microwave absorbers are a subject of high priority. These are due to the fast development of telecommunication technologies and the need to reduce electromagnetic pollution. Such materials are implementable in multiple industries, including military, medical, and laboratory equipment. One should remember that the desired material should exhibit a high total shielding effectiveness SE$_{T}$ and controllable performance properties. In this work, an ultrathin graphene oxide paper is fabricated and verified as a wide-range, controllable microwave absorber. Stepwise (100$^\circ$ C – 200$^\circ$ C – 300$^\circ$ C) thermally reduced G-Flake graphene oxide paper of 4.95 μm thickness revealed the conductivity of 1.86 S/cm. A mild level of reduction was proven with combustion elemental analysis, resulting in a 22.4 oxygen percentage (50.9 % before the reduction). Raman spectroscopy suggested the limitation of Stone-Wales defects after heat treatment. Microwave absorption was measured in the W-band frequency region, and the SE$_{T}$ /t parameter reached 606 dB/mm for a c.a. 5-μm-thick individual reduced paper sheet. The controlled increase in conductivity resulted in conduction losses, and the occurrence of pores enabled scattering, while the absorption remained the primary shielding mechanism.- 4 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nanotechnology
- Vol. 23 (1536125X) , 329-337
Graphene Oxide Paper as a Lightweight, Thin, and Controllable Microwave Absorber for Millimeter-Wave Applications
The production and verification of microwave absorbers are a subject of high priority. These are due to the fast development of telecommunication technologies and the need to reduce electromagnetic pollution. Such materials are implementable in multiple industries, including military, medical, and laboratory equipment. One should remember that the desired material should exhibit a high total shielding effectiveness SE$_{T}$ and controllable performance properties. In this work, an ultrathin graphene oxide paper is fabricated and verified as a wide-range, controllable microwave absorber. Stepwise (100$^\circ$ C – 200$^\circ$ C – 300$^\circ$ C) thermally reduced G-Flake graphene oxide paper of 4.95 μm thickness revealed the conductivity of 1.86 S/cm. A mild level of reduction was proven with combustion elemental analysis, resulting in a 22.4 oxygen percentage (50.9 % before the reduction). Raman spectroscopy suggested the limitation of Stone-Wales defects after heat treatment. Microwave absorption was measured in the W-band frequency region, and the SE$_{T}$ /t parameter reached 606 dB/mm for a c.a. 5-μm-thick individual reduced paper sheet. The controlled increase in conductivity resulted in conduction losses, and the occurrence of pores enabled scattering, while the absorption remained the primary shielding mechanism.- 20 March 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 26 (9) , 2301920
Hybrid Epoxy Composites Based on Basalt Fabric: A Case Study of Low‐Temperature Plasma Treatment and Reduced Graphene Oxide Flakes Addition
The purpose of this study is to present a novel method for producing mechanically strong epoxy composite laminates of different compositions, reinforced with basalt fabric and reduced graphene oxide flakes. The laminates are prepared with basalt fabric, which is subjected to low‐temperature plasma treatment. This approach is aimed to enhance the adhesion of fabric to resin filled with reduced graphene oxide flakes. Physical properties, adhesion, and mechanical properties of the obtained materials are determined. Based on the experiments, it is found that the tensile strength is improved by 6–21% after using reduced graphene oxide filler, 9–23% after plasma treatment, and up to 27% using the combination of plasma and reduced graphene. It is found that the highest improvement of tensile strength is obtained for epoxy composite with 0.5 wt% graphene‐based filler and 3 min basalt fiber plasma treatment with 25 W plasma power.
- 20 March 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 26 (9) , 2301920
Hybrid Epoxy Composites Based on Basalt Fabric: A Case Study of Low‐Temperature Plasma Treatment and Reduced Graphene Oxide Flakes Addition
The purpose of this study is to present a novel method for producing mechanically strong epoxy composite laminates of different compositions, reinforced with basalt fabric and reduced graphene oxide flakes. The laminates are prepared with basalt fabric, which is subjected to low‐temperature plasma treatment. This approach is aimed to enhance the adhesion of fabric to resin filled with reduced graphene oxide flakes. Physical properties, adhesion, and mechanical properties of the obtained materials are determined. Based on the experiments, it is found that the tensile strength is improved by 6–21% after using reduced graphene oxide filler, 9–23% after plasma treatment, and up to 27% using the combination of plasma and reduced graphene. It is found that the highest improvement of tensile strength is obtained for epoxy composite with 0.5 wt% graphene‐based filler and 3 min basalt fiber plasma treatment with 25 W plasma power.
- Open Access
Hydrothermal Synthesis of Zinc Oxide Nanoparticles Using Different Chemical Reaction Stimulation Methods and Their Influence on Process Kinetics
The aim of this work was to study the effect of the applied chemical reaction stimulation method on the morphology and structural properties of zinc oxide nanoparticles (ZnONPs). Various methods of chemical reaction induction were applied, including microwave, high potential, conventional resistance heater and autoclave-based methods. A novel, high potential-based ZnONPs synthesis method is herein proposed. Structural properties–phase purity, grain size–were examined with XRD methods, the specific surface area was determined using BET techniques and the morphology was examined using SEM. Based on the results, the microwave and autoclave syntheses allowed us to obtain the desired phase within a short period of time. The impulse-induced method is a promising alternative since it offers a non-equilibrium course of the synthesis process in an highly energy-efficient manner.
Open AccessHydrothermal Synthesis of Zinc Oxide Nanoparticles Using Different Chemical Reaction Stimulation Methods and Their Influence on Process Kinetics
The aim of this work was to study the effect of the applied chemical reaction stimulation method on the morphology and structural properties of zinc oxide nanoparticles (ZnONPs). Various methods of chemical reaction induction were applied, including microwave, high potential, conventional resistance heater and autoclave-based methods. A novel, high potential-based ZnONPs synthesis method is herein proposed. Structural properties–phase purity, grain size–were examined with XRD methods, the specific surface area was determined using BET techniques and the morphology was examined using SEM. Based on the results, the microwave and autoclave syntheses allowed us to obtain the desired phase within a short period of time. The impulse-induced method is a promising alternative since it offers a non-equilibrium course of the synthesis process in an highly energy-efficient manner.
- 23 May 2022
- Published by Elsevier in Ceramics International
- Vol. 48 (17) , 24935-24942
Effect of annealing in argon atmosphere on the properties of zinc oxide nanoparticles doped with Mn(II) and Co(II) ions prepared in solvothermal synthesis
- 23 May 2022
- Published by Elsevier in Ceramics International
- Vol. 48 (17) , 24935-24942
Effect of annealing in argon atmosphere on the properties of zinc oxide nanoparticles doped with Mn(II) and Co(II) ions prepared in solvothermal synthesis
- Open Access
Luminescence Properties of Nano Zinc Oxide Doped with Al(III) Ions Obtained in Microwave-Assisted Hydrothermal Synthesis
The hydrothermal method of obtaining nano zinc oxide doped with different contents of aluminum ions (III) was presented and discussed in this paper. Aqueous solution of Zn(NO3)2*6H2O and Al(NO3)3*9H2O salts mixture were used as the synthesis precursor. In order to reduce the process time all reactions were performed in a microwave reactor. The influence of process parameters and the content of impurity ions on the properties of synthesized nano zinc oxide were analyzed. In addition to zinc oxide doped with Al(III) ions, an additional spinel phase (ZnAl2O4) was obtained. The luminescent properties of nano zinc oxide as a function of the dopant ions were also discussed. Based on the luminescence measurements results, it was found that the luminescence intensity decreases with the increasing dopant content. The obtained materials are aimed to be implemented as luminescent materials in optoelectronic and sensors.
Open AccessLuminescence Properties of Nano Zinc Oxide Doped with Al(III) Ions Obtained in Microwave-Assisted Hydrothermal Synthesis
The hydrothermal method of obtaining nano zinc oxide doped with different contents of aluminum ions (III) was presented and discussed in this paper. Aqueous solution of Zn(NO3)2*6H2O and Al(NO3)3*9H2O salts mixture were used as the synthesis precursor. In order to reduce the process time all reactions were performed in a microwave reactor. The influence of process parameters and the content of impurity ions on the properties of synthesized nano zinc oxide were analyzed. In addition to zinc oxide doped with Al(III) ions, an additional spinel phase (ZnAl2O4) was obtained. The luminescent properties of nano zinc oxide as a function of the dopant ions were also discussed. Based on the luminescence measurements results, it was found that the luminescence intensity decreases with the increasing dopant content. The obtained materials are aimed to be implemented as luminescent materials in optoelectronic and sensors.
- 1 January 2022
- Published by Elsevier in Optical Materials
- Vol. 123
Luminescence and energy transfer processes in LuNbO4:Bi, Eu
- 1 January 2022
- Published by Elsevier in Optical Materials
- Vol. 123
Luminescence and energy transfer processes in LuNbO4:Bi, Eu
- Open Access
Microwave-Assisted Hydrothermal Synthesis of Zinc-Aluminum Spinel ZnAl2O4
The drawback of the hydrothermal technique is driven by the fact that it is a time-consuming operation, which greatly impedes its commercial application. To overcome this issue, conventional hydrothermal synthesis can be improved by the implementation of microwaves, which should result in enhanced process kinetics and, at the same time, pure-phase and homogeneous products. In this study, nanometric zinc aluminate (ZnAl2O4) with a spinel structure was obtained by a hydrothermal method using microwave reactor. The average ZnAl2O4 crystallite grain size was calculated from the broadening of XRD lines. In addition, BET analysis was performed to further characterize the as-synthesized particles. The synthesized materials were also subjected to microscopic SEM and TEM observations. Based on the obtained results, we concluded that the grain sizes were in the range of 6–8 nm. The surface areas measured for the samples from the microwave reactor were 215 and 278 m2 g−1.
Open AccessMicrowave-Assisted Hydrothermal Synthesis of Zinc-Aluminum Spinel ZnAl2O4
The drawback of the hydrothermal technique is driven by the fact that it is a time-consuming operation, which greatly impedes its commercial application. To overcome this issue, conventional hydrothermal synthesis can be improved by the implementation of microwaves, which should result in enhanced process kinetics and, at the same time, pure-phase and homogeneous products. In this study, nanometric zinc aluminate (ZnAl2O4) with a spinel structure was obtained by a hydrothermal method using microwave reactor. The average ZnAl2O4 crystallite grain size was calculated from the broadening of XRD lines. In addition, BET analysis was performed to further characterize the as-synthesized particles. The synthesized materials were also subjected to microscopic SEM and TEM observations. Based on the obtained results, we concluded that the grain sizes were in the range of 6–8 nm. The surface areas measured for the samples from the microwave reactor were 215 and 278 m2 g−1.
- 1 October 2007
- Published by Elsevier in Photonics and Nanostructures - Fundamentals and Applications
- Vol. 5 (2-3) , 125-128
Modification of photonic properties in porphyrin-infiltrated opal crystals
- 1 October 2007
- Published by Elsevier in Photonics and Nanostructures - Fundamentals and Applications
- Vol. 5 (2-3) , 125-128
Modification of photonic properties in porphyrin-infiltrated opal crystals