Shih-Kuen Changchien
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Shih-Kuen Changchien has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Chuan-Kuei Huang
Department of Electrical Engineering, Chienkuo Technology University, Changhua 500, Taiwan
1 shared publicationHong-Wei Shieh
Department of Electrical Engineering, Chienkuo Technology University, Changhua 500, Taiwan
1 shared publicationHsiau-Hsian Nien
Department of Electrical Engineering, Chienkuo Technology University, Changhua 500, Taiwan
1 shared publicationJ. F. Chen
Power Electronics Laboratory, Department of Electrical Engineering, National Cheng-Kung University, No. 1, Ta-Hseuh Road, Tainan City, Taiwan, R.O.C.
1 shared publicationK. C. Tseng
Power Electronics Laboratory, Department of Electrical Engineering, National Cheng-Kung University, No. 1, Ta-Hseuh Road, Tainan City, Taiwan, R.O.C.
1 shared publication- Kun-Li Wen
Chienkuo Technology University
1 shared publication
Latest Publications
- Open Access
The Influence Factor Analysis of Symmetrical Half-Bridge Power Converter through Regression, Rough Set and GM(1,N) Model
Analysis of power converter performance has tended to be engineering-oriented, focusing mainly on voltage stability, output power and efficiency improvement. However, there has been little discussion about the weight relations between these factors. In view of the previous inadequacy, this study employs regression, rough set and GM(1,N) to analyze the relations among the factors that affect the converter, with a symmetrical half-bridge power converter serving as an example. The four related affecting factors, including the current conversion ratio, voltage conversion ratio, power conversion ratio and output efficiency, are firstly analyzed and calculated. The respective relative relations between output efficiency and the other three factors are obtained. This research can be referred to by engineers in their design of symmetrical half-bridge power converters.
Open AccessThe Influence Factor Analysis of Symmetrical Half-Bridge Power Converter through Regression, Rough Set and GM(1,N) Model
Analysis of power converter performance has tended to be engineering-oriented, focusing mainly on voltage stability, output power and efficiency improvement. However, there has been little discussion about the weight relations between these factors. In view of the previous inadequacy, this study employs regression, rough set and GM(1,N) to analyze the relations among the factors that affect the converter, with a symmetrical half-bridge power converter serving as an example. The four related affecting factors, including the current conversion ratio, voltage conversion ratio, power conversion ratio and output efficiency, are firstly analyzed and calculated. The respective relative relations between output efficiency and the other three factors are obtained. This research can be referred to by engineers in their design of symmetrical half-bridge power converters.
- 28 February 2009
- Published by Elsevier in Chaos, Solitons & Fractals
- Vol. 39 (4) , 1578-1587
Synchronization of the chaotic secure communication system with output state delay
- 28 February 2009
- Published by Elsevier in Chaos, Solitons & Fractals
- Vol. 39 (4) , 1578-1587
Synchronization of the chaotic secure communication system with output state delay
- 1 January 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 1553572X,p. 1390-1395
A Demagnetization Circuit for Single-Ended Forward Converter
This paper presents a novel demagnetization scheme for single-ended forward converter. In the past, many prior transformer core reset methods have been proposed in order to avoid the transformer saturation, such as tertiary transformer winding, RCD clamp, resonant reset, active clamp and two-switch forward topology etc.. However, the lower efficiency, complicated transformer winding structure and the cost of too many added elements are the main drawbacks. In this paper, a novel demagnetization scheme for single-ended forward converter is presented. The proposed demagnetization circuit is very simple and the transformer demagnetization can be reached by adding two diodes and a clamping capacitor. In addition, the transformer design and PWM control circuit for the single-ended forward converter with proposed demagnetization circuit is the same as conventional forward converter. Finally, the operation and circuit performance of the single-ended forward converter with proposed demagnetization circuit are demonstrated with an experimental prototype that delivers a 5 V/10 A output from a 36-72 V input at the maximum efficiency of 88%.
- 1 January 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 1553572X,p. 1390-1395
A Demagnetization Circuit for Single-Ended Forward Converter
This paper presents a novel demagnetization scheme for single-ended forward converter. In the past, many prior transformer core reset methods have been proposed in order to avoid the transformer saturation, such as tertiary transformer winding, RCD clamp, resonant reset, active clamp and two-switch forward topology etc.. However, the lower efficiency, complicated transformer winding structure and the cost of too many added elements are the main drawbacks. In this paper, a novel demagnetization scheme for single-ended forward converter is presented. The proposed demagnetization circuit is very simple and the transformer demagnetization can be reached by adding two diodes and a clamping capacitor. In addition, the transformer design and PWM control circuit for the single-ended forward converter with proposed demagnetization circuit is the same as conventional forward converter. Finally, the operation and circuit performance of the single-ended forward converter with proposed demagnetization circuit are demonstrated with an experimental prototype that delivers a 5 V/10 A output from a 36-72 V input at the maximum efficiency of 88%.