R. O. Sotnikov
Research Subjects
R. O. Sotnikov has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Maria A. Vilner
Санкт-Петербургский горный университет
1 shared publication - Maxim Anatolyevich Karasev
Saint Petersburg Mining University
1 shared publication - Mikhail G. Popov
Department of Constructing Mining Enterprises and Underground Structures, Saint-Petersburg Mining University, 21-st Line V.O., 2, 199106 Saint-Petersburg, Russia
1 shared publication V. Yu. Sinegubov
1 shared publication
Latest Publications
- Open Access
- 29 October 2021
- Published by Saint-Petersburg Mining University in Journal of Mining Institute
- Vol. 251, 626-638
Prediction of the stress state of the shotcreting support under repeated seismic load
The article assesses the impact of repeated blasts on the stress-strain state of the shotcreting support, which negatively affects the bearing capacity of the support and can lead to the formation of local rock falls in places of significant degradation of the shotcreting strength. Despite the fact that a single seismic load usually does not have a significant impact on the technical condition of the shotcreting support, repeated dynamic loading can lead to the development of negative processes and affect the safety. The article considers unreinforced and dispersed-reinforced shotcreting concrete as a shotcreting support. Models of deformation of rock and shotcreting support have been studied. To describe the deformation model of a rock mass, an elastic–plastic model based on the Hook-Brown plasticity condition has been accepted, which accurately describes the elastic-plastic behavior of a fractured medium. When performing the prediction of the stress-strain state of the shotcreting support, a model of plastic deformation of concrete with the accumulation of Concrete Damage Plasticity (CDP) was adopted, which allows to comprehensively consider the process of concrete deformation both under conditions of uniaxial compression and stress, and with minor edging draft. At the first calculation stage, a forecast of the seismic waves propagation in the immediate vicinity of the explosive initiation site was made. At the second stage, forecasts of the seismic waves propagation to the mine working and the stress-strain state of the support were made. On the basis of the performed studies, a methodology for assessing the impact of repeated blasts on the stress-strain state of the shotcreting support of the mine working is proposed. В статье оценивается влияние повторяющихся взрывов на напряженно-деформированное состояние набрызг-бетонной крепи, которое негативно сказывается на несущей способности крепи и может привести к формированию локальных вывалов пород в местах значительной деградации прочности набрызг-бетона. Несмотря на то, что однократное сейсмическое воздействие обычно не оказывает значительного влияния на техническое состояние набрызг-бетонной крепи, многократное динамическое нагружение может привести к развитию негативных процессов и повлиять на безопасность людей. В качестве набрызг-бетонной крепи рассмотрен неармированный и дисперсно-армированный набрызг-бетон. Изучены модели деформирования горной породы и набрызг-бетонной крепи. Для описания модели деформирования породного массива принята упругопластическая модель, основанная на условии пластичности Хука – Брауна, которая достаточно точно описывает упругопластическое поведение трещиноватой среды. При выполнении прогноза напряженно-деформированного состояния набрызг-бетонной крепи принята модель пластического деформирования бетона с накоплением повреждений Concrete Damage Plasticity (CDP), которая позволяет комплексно рассмотреть процесс деформирования бетона как при условиях одноосного сжатия и растяжения, так и при незначительном боковом обжатии. На первом расчетном этапе выполнен прогноз распространения сейсмических волн в непосредственной близости от участка инициации взрывчатого вещества. На втором этапе выполнены прогнозы распространения сейсмических волн до горной выработки и напряженно-деформированного состояния крепи. На основании выполненных исследований предложена методика оценки воздействия повторяющихся взрывов на напряженно-деформированное состояние набрызг-бетонной крепи горной выработки.
- 29 October 2021
- Published by Saint-Petersburg Mining University in Journal of Mining Institute
- Vol. 251, 626-638
Open AccessPrediction of the stress state of the shotcreting support under repeated seismic load
The article assesses the impact of repeated blasts on the stress-strain state of the shotcreting support, which negatively affects the bearing capacity of the support and can lead to the formation of local rock falls in places of significant degradation of the shotcreting strength. Despite the fact that a single seismic load usually does not have a significant impact on the technical condition of the shotcreting support, repeated dynamic loading can lead to the development of negative processes and affect the safety. The article considers unreinforced and dispersed-reinforced shotcreting concrete as a shotcreting support. Models of deformation of rock and shotcreting support have been studied. To describe the deformation model of a rock mass, an elastic–plastic model based on the Hook-Brown plasticity condition has been accepted, which accurately describes the elastic-plastic behavior of a fractured medium. When performing the prediction of the stress-strain state of the shotcreting support, a model of plastic deformation of concrete with the accumulation of Concrete Damage Plasticity (CDP) was adopted, which allows to comprehensively consider the process of concrete deformation both under conditions of uniaxial compression and stress, and with minor edging draft. At the first calculation stage, a forecast of the seismic waves propagation in the immediate vicinity of the explosive initiation site was made. At the second stage, forecasts of the seismic waves propagation to the mine working and the stress-strain state of the support were made. On the basis of the performed studies, a methodology for assessing the impact of repeated blasts on the stress-strain state of the shotcreting support of the mine working is proposed. В статье оценивается влияние повторяющихся взрывов на напряженно-деформированное состояние набрызг-бетонной крепи, которое негативно сказывается на несущей способности крепи и может привести к формированию локальных вывалов пород в местах значительной деградации прочности набрызг-бетона. Несмотря на то, что однократное сейсмическое воздействие обычно не оказывает значительного влияния на техническое состояние набрызг-бетонной крепи, многократное динамическое нагружение может привести к развитию негативных процессов и повлиять на безопасность людей. В качестве набрызг-бетонной крепи рассмотрен неармированный и дисперсно-армированный набрызг-бетон. Изучены модели деформирования горной породы и набрызг-бетонной крепи. Для описания модели деформирования породного массива принята упругопластическая модель, основанная на условии пластичности Хука – Брауна, которая достаточно точно описывает упругопластическое поведение трещиноватой среды. При выполнении прогноза напряженно-деформированного состояния набрызг-бетонной крепи принята модель пластического деформирования бетона с накоплением повреждений Concrete Damage Plasticity (CDP), которая позволяет комплексно рассмотреть процесс деформирования бетона как при условиях одноосного сжатия и растяжения, так и при незначительном боковом обжатии. На первом расчетном этапе выполнен прогноз распространения сейсмических волн в непосредственной близости от участка инициации взрывчатого вещества. На втором этапе выполнены прогнозы распространения сейсмических волн до горной выработки и напряженно-деформированного состояния крепи. На основании выполненных исследований предложена методика оценки воздействия повторяющихся взрывов на напряженно-деформированное состояние набрызг-бетонной крепи горной выработки.
- 31 August 2021
- Published by Ore and Metals Publishing House in Gornyi Zhurnal
- p. 26-30
Influence of stoping on formation of damaged rock zones at boundaries of large cross-section excavations in apatite–nepheline mining
Introduction of new equipment in the production cycle in mines can greatly accelerate the pace of construction and can increase production output. And yet considerable time is spent on preparatory works, transport operations and shunting. To reduce the time consumption, engineers make nonroutine decisions on the arrangement of process equipment in underground excavations, which imposes certain requirements on their geometry and support design. For example, the design size of grinding chambers can exceed 14 m in height and 8 m in width. These dimensions are almost 2 times higher than the size stated in the regulatory documents. The mine support design guidelines are unadapted to the dimensions of such underground openings, and disregard the construction sequence, complicated geological and mining conditions, and the influence of stoping. As a result, geomechanical processes in the vicinity of large cross-section excavations in fractured rock masses can only be estimated approximately. This paper proposes a mathematical modeling algorithm including rock mass fracture intensity, the length/width ratio of a large cross-section excavation and the presence of junctions with other excavations. Such stress–strain analysis of tock mass provides the pattern of geomechanical behavior in the vicinity of the underground excavation, namely, it allows determining the change patterns of damaged zones in rock mass. It is shown that stoping can lead to an increase in the size of the limit state zones up to 3 times, which exceeds the safety factor as per the regulatory documents. The obtained results can widen the field of application of regulatory documents in mining.
- 31 August 2021
- Published by Ore and Metals Publishing House in Gornyi Zhurnal
- p. 26-30
Influence of stoping on formation of damaged rock zones at boundaries of large cross-section excavations in apatite–nepheline mining
Introduction of new equipment in the production cycle in mines can greatly accelerate the pace of construction and can increase production output. And yet considerable time is spent on preparatory works, transport operations and shunting. To reduce the time consumption, engineers make nonroutine decisions on the arrangement of process equipment in underground excavations, which imposes certain requirements on their geometry and support design. For example, the design size of grinding chambers can exceed 14 m in height and 8 m in width. These dimensions are almost 2 times higher than the size stated in the regulatory documents. The mine support design guidelines are unadapted to the dimensions of such underground openings, and disregard the construction sequence, complicated geological and mining conditions, and the influence of stoping. As a result, geomechanical processes in the vicinity of large cross-section excavations in fractured rock masses can only be estimated approximately. This paper proposes a mathematical modeling algorithm including rock mass fracture intensity, the length/width ratio of a large cross-section excavation and the presence of junctions with other excavations. Such stress–strain analysis of tock mass provides the pattern of geomechanical behavior in the vicinity of the underground excavation, namely, it allows determining the change patterns of damaged zones in rock mass. It is shown that stoping can lead to an increase in the size of the limit state zones up to 3 times, which exceeds the safety factor as per the regulatory documents. The obtained results can widen the field of application of regulatory documents in mining.