SBSalina Budin

Salina Budin

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Salina Budin has a total of 34 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    The Effect of Layer Thickness on Repeatability of 3d Printed PLA Parts Produced Using Openware 3D Printer

    by Normariah Che Maideen, Mohd Ikmal Hisham Abdul Rahim, Salina Budin, Koay Mei Hyie, Hamid Yusoff

    Fused Filament Fabrication (FFF) is categorized as an additive manufacturing process, recognized as the simplest way to accomplish 3D printing. Previous studies have proven that FFF can be trusted to create custom parts with high complexity. However, some performance issues still exist with this method that must be resolved to improve conventional manufacturing techniques. One of them is its repeatability performance that is debatable when it comes to producing repetitive runs of similar parts. Printing parameter is one of the factors that play a significant role on the repeatability performance of parts produced. In this study, the effect of layer thickness on the repeatability of 3D printed PLA, produced using an Openware 3D printer (Espresso F220), was investigated. Two product geometries (Part A and Part B) were produced. Layer thickness was chosen as a variable parameter (0.1 mm, 0.2 mm, and 0.3 mm) for each geometry. Data to measure repeatability of the printed PLA parts were determined based on the measurements of length, width, thickness and surface roughness for each geometry. Then, repeatability performance was analyzed through One-way ANOVA analysis. From the results, the layer thickness parameter did influence dimensional quality and repeatability of samples produced. Part length and thickness offered better repeatability performance, to both product geometries being compared, in width and surface roughness. The study reveals that variations in sample properties depends on not only one, but also every printing parameter involved. Repeatability performance can be improved by identifying the ideal combination of printing parameters to produce good part quality. ABSTRAK: : Fabrikasi Filamen Fius (FFF) yang dikategori sebagai proses pembuatan tambahan, diakui sebagai kaedah termudah bagi menghasilkan pencetakan 3D. Kajian terdahulu telah membuktikan bahawa FFF dapat menghasilkan komponen khas yang kompleks. Walau bagaimanapun, beberapa isu peningkatan mutu masih berlaku, iaitu kaedah ini masih perlu diperbetulkan bagi membaiki teknik pembuatan konvensional. Salah satu adalah peningkatan keterulangan bagi menghasilkan komponen yang serupa secara berulang. Parameter pencetakan adalah salah satu faktor yang berperanan penting bagi peningkatan keterulangan komponen yang dihasilkan. Kajian ini mengkaji tentang kesan ketebalan lapisan terhadap kebolehulangan PLA bercetak 3D yang dihasilkan melalui pencetak Openware 3D (Espresso F220). Dua geometri produk (bahagian A dan B) dihasilkan. Ketebalan lapisan dipilih sebagai parameter pemboleh ubah (0.1mm, 0.2mm dan 0.3mm) bagi setiap geometri. Data bagi mengukur keterulangan bahagian PLA yang bercetak ditentukan berdasarkan pengukuran panjang, lebar, ketebalan dan kekasaran permukaan bagi setiap geometri. Kemudian, peningkatan keterulangan dianalisa melalui analisis ANOVA Sehala. Dapatan hasil menunjukkan, parameter ketebalan lapisan mempengaruhi kualiti dimensi dan kebolehulangan sampel yang dihasilkan. Panjang dan ketebalan bahagian mempunyai peningkatan keterulangan yang lebih baik bagi kedua-dua geometri produk berbanding lebar dan kekasaran permukaan. Dapatan menunjukkan bahawa variasi sifat sampel tidak hanya bergantung pada satu, malah pada setiap parameter pencetakan yang terlibat. Peningkatan keterulangan dapat diperbaiki dengan mengenal pasti kombinasi parameter pencetakan yang ideal bagi menghasilkan kualiti bahagian terbaik.


  • Open Access

    An Experimental Study of Indoor Air Pollution in New Office Building

    by Nor Azirah Mohd Fohimi, Koay Mei Hyie, Salina Budin, Normariah Che Maideen, Nazri Kamsah, Haslinda Mohamed Kamar

    Air pollution is a major environmental risk to health. The new building normally has a facing problem with indoor air pollutant. New construction materials and furniture will contribute higher contaminants compared to old materials. The effect of indoor air pollutants can result in human health problems, discomfort and reduces their productivity. The purpose of this present work is to experimental study the indoor air pollution status regarding carbon dioxide, carbon monoxide, volatile organic compounds, and formaldehyde concentration in an administration office at the new building faculty of mechanical engineering in Johor Bahru, Malaysia. The contaminants concentration values are investigated through field measurements and then compared to the limits stated in the Occupational Safety and Health Act standard. The field measurement of contaminant concentration level was conducted at the intersect plane between the vertical plane at the center of the air conditioning diffuser and the horizontal plane at 1.2 m from the floor. The contaminant concentration readings were taken at 6 locations inside the office. The data were conducted during actual working conditions. The reading of contaminants concentration is taken in 30 minutes. One minute is equal to one number of samples. It was found that only the formaldehyde concentration is exceeding the maximum limit.


  • Open Access

    COMPARATIVE STUDY ON DEGRADATION OF POLYLACTIC ACID/ SYZYGIUM AROMATICUM COMPOSITES AGEING IN OUTDOOR ENVIRONMENT AND SOIL BURIAL

    by Salina Budin, Normariah Che Maideen, Mei Hyie Koay, Hamid Yusoff, Halim Ghafar

    Major environmental problems resulting from non-degradable components of plastic wastes have awakened great attention to bioplastic as an alternative material. Among various bioplastic materials, polylactic acid (PLA) is recognised as a promising material especially as a food packaging material. The development of PLA composites using various fillers has extensively been in focus in order to preserve the high quality, safety, and extended shelf-life of packed food. Among the interesting fillers is Syzygium aromaticum (SA). SA, also known as clove, has biological activities such as antibacterial, antifungal, insecticidal, and antioxidant properties. This work investigated the effects of SA filler on the degradations of virgin PLA (VPLA) and recycled PLA (RPLA). The VPLA/SA composites and RPLA/SA composites were prepared using the solvent casting method. The content of SA filler varied in the range of 0 to 20 wt%. The composites were aged in outdoor environment and soil burial. The results revealed that the degradation rate was increased with the increase of SA filler in both ageing environments. After 10 weeks of ageing in the outdoor environment, the weight loss of VPLA/SA composites and RPLA/SA composites containing 20 wt% of SA were 7.7% and 12.8% respectively. Whereas in soil burial, the weight loss of VPLA/SA composites and RPLA/SA composites with similar SA content were 25.6% and 38.3% respectively. The degradation rate was observed to be more rapid in the soil burial as compared to the outdoor environment. Comparably, RPLA and RPLA/SA composites experienced higher degradation rates than VPLA and VPLA/SA composites. The degradation rate was consistent with scanning electron microscope (SEM) images which observed the formation of holes, cavities, cleavages, and grooves on the surfaces of the samples. Thermogravimetric analysis (TGA) results on aged samples showed that VPLA/SA composites and RPLA/SA composites that had aged in soil burial decomposed at lower temperatures. The shortening of degradation time of the VPLA/SA composites and RPLA/SA composites could increase their potential to be used as food packaging materials. ABSTRAK: Masalah utama terhadap alam sekitar yang disebabkan oleh sisa plastik yang sukar terurai, telah menarik perhatian terhadap bioplastik sebagai bahan alternatif. Di antara pelbagai jenis bahan bioplastik sedia ada, asid polilaktik(PLA) dilihat sebagai bahan yang paling sesuai terutamanya sebagai bahan pembungkusan makanan. Perkembangan di dalam penghasilan komposit asid polilaktik yang ditambah dengan pelbagai bahan pengisi telah menjadi fokus terutamanya bagi tujuan meningkatkan kualiti, kesegaran dan jangka hayat makanan. Salah satu pengisi yang mendapat perhatian adalah Syzygium aromaticum (SA). SA yang juga dikenali sebagai bunga cengkeh mempunyai aktiviti biologi, seperti sifat antibakteria, antijamur, racun serangga dan antioksidan yang tinggi. Didalam kajian ini, siasatan terhadap kesan penambahan SA terhadap penguraian PLA asal (VPLA) dan PLA kitar semula (VPLA). Komposit VPLA/SA dan komposit RPLA/SA disediakan dengan menggunakan kaedah pelarutan pelarut. Kandungan pengisi SA adalah didalam julat 0 – 20% mengikut berat. Komposit tersebut dibiarkan menua didalam persekitaran luaran dan didalam tanah. Keputusan kajian mendapati bahawa kadar penguraian semakin meningkat dengan penambahan peratus berat bahan pengisi SA setelah melalui penuaan didalam kedua-dua persekitaran. Setelah penuaan selama10 minggu di dalam persekiran luaran, pengurang berat komposit VPLA/SA dan komposit RPLA/SA yang mengandungi 20 wt% SA adalah 7.7% dan 12.8%. Manakala bagi penuaan didalam tanah, pengurangan berat komposit VPLA/SA dan komposit RPLA/SA dengan kandungan SA yang sama masing-masing adalah 25.6% dan 38.3%. Kadar penguraian diperhatikan lebih cepat bagi penuan didalam tanah dibandingkan dengan penuaan didalam persekitaran luaran. Disamping itu, RPLA dan komposit RPLA/SA mengalami kadar penguraian yang lebih tinggi berbanding VPLA dan komposit VPLA/SA. Kadar penguraian adalah konsisten dengan imej yang dihasilkan oleh imbasan mikroskop elektron (SEM) dimana dapat dilihat pembentukan lubang, rongga, pembelahan dan alur di permukaan sampel. Hasil analisis termogravimetri (TGA) terhadap sampel yang telah dituakan menunjukkan bahawa komposit VPLA/SA dan komposit RPLA/SA yang melalui penuaan didalam tanah terurai pada suhu yang lebih rendah. Tempoh penguraian komposit VPLA/SA dan komposit RPLA/SA yang lebih pendek ini meningkatkan potensi penggunaannya komposit ini sebagai bahan pembungkusan makanan.


  • Open Access

    Degradation on mechanical properties of virgin and recycled polylactic acid ageing in aqueous environment

    by S Budin, M H Koay, N C Maideen

    A growing demand in polylactic acid (PLA) has increased in recent years due to the increasing of non-degradable plastic wastes. The recycling of PLA waste is seen to be another permissible solution to conserve the resources. This work aims to study the degradation rate of virgin PLA (VPLA) and recycled PLA (RPLA) in terms of the mechanical properties after ageing in different aqueous environment. The samples were immersed in river water (RW) and seawater (SW) for the duration of 150 days. Tensile strength, transverse rupture strength (TRS), impact energy and hardness properties were investigated as a function of immersed time. The results revealed that the loss in the tensile strength accelerated in river water when compared to seawater. There was at least 50% of tensile strength sacrificed in recycled PLA. The TRS had dropped approximately half from its initial value after ageing in river water and about 30% after ageing in seawater. Besides, a huge decrease ranging around 70-80% from its initial impact energy was identified. However, the reduction in hardness was relatively low. The findings will help to elucidate the degradation process of PLA and the desired effect on the mechanical performance for further application.


  • Open Access

    Decision Support System for Selection and Assessment of Solid Waste Processing Technology from Oil Palm Industry using Analytical Hierarchy Process (AHP)

    by Aulia Ishak, Amir Yazid bin Ali, Salina Budin, Rosnani Ginting

    The waste produced by the palm oil industry contributes greatly to environmental damage if it is not operated properly. Waste from palm oil processing consists of 70% of the amount of raw material which is almost half in the form of liquid. Over time the growth of the palm oil industry has always increased, therefore the waste from the palm oil industry will increase. The palm oil industry must have environmentally friendly solid waste treatment technology that is able to provide added value. There are many alternatives to treat the palm oil industry’s solid waste, from the most advanced technology to conventional technology. Decision Support Systems have been developed to assist companies in identifying, evaluating and choosing technologies for processing solid waste. In this study, three operations have been developed in MySQL, the database for waste treatment technology has criteria and sub criteria selection criteria using the DELPHI method; Introduction of criteria using the Analytical Hierarchy Process (AHP) approach. This study can assist in decision making and optimize the reprocessing of solid waste from palm oil mills.


  • Open Access

    Kenaf/polypropylene key chain product fabricated by injection moulding

    by M H Koay, Z Salleh, N R N M Masdek, S Budin, A Ngu

    The natural fiber composites product becomes popular among the world to promote sustainable development. Unlike the synthetic fibers, natural fibers can absorb as much as the carbon dioxide to prevent the global warming happened. Natural fiber composites such as kenaf mixed with polypropylene, have been commercialized in automotive parts due to its lightweight ability which can improve the fuel efficiency. The main objective of this study is to investigate the effect of injection moulding temperature to the shrinkage and tensile properties of kenaf/polypropylene key chain product. The optimum weight fraction of 30 wt% kenaf and 70 wt% polypropylene was fabricated using different temperatures of the injection moulding process. The best physical appearance of the key chain was prepared at 180°C. The sample that was fabricated at 210°C has higher tensile stress and tensile modulus which are 12.48 MPa and 1.03 GPa, respectively. As a conclusion, the kenaf/polypropylene specimen prepared at 210 °C has better tensile strength and less shrinkage if compared to others. Brittleness due to voids formation was evident in the SEM image of the kenaf/polypropylene. By using the injection moulding process, a high volume of products could be produced in a very short time.


  • Open Access

    A comparison study on mechanical properties of virgin and recycled polylactic acid (PLA)

    by S Budin, N C Maideen, M H Koay, D Ibrahim, H Yusoff

    Huge usage of Polylactic Acid (PLA) has contributed to the high wastes which mainly come from the worn parts. Recycling of the wastes is seen to be a permissible solution to reduce the quantity of wastes in the landfills. This work aims to compare the mechanical properties of virgin and recycled PLA. The recycled material is collected from the waste produces from the injection molding process. The mechanical testing samples for both virgin and recycled materials are prepared using an injection molding process. The results show that the mechanical properties of recycled PLA lower than the virgin PLA. The tensile strength of recycled PLA decreases by 11% as compared to virgin PLA. On the other hand, TRS is also observed drop by 5% for recycled PLA compared to virgin PLA. A similar trend is found in the impact strength and hardness of properties where its impact strength drops by 50% of recycled PLA. For hardness property, it is noted that the hardness decreases by 4% of the recycled PLA. The decreasing value of the mechanical properties is due to thermal degradation of the PLA molecular chain during the injection molding process which has consequently affected the mechanical properties of the recycled PLA.