Luis Fernández

In this work, the enzymatic synthesis of pentyl acetate obtained from acetic acid and pentan-1-ol using the commercial immobilized lipase Lipozyme^®435 was studied. Specifically, the effects of several variables of the process on the kinetics were shown, such as the initial concentration of the acetic acid, the alcohol/acid molar ratio, and the possible reuse of the enzyme, while other variables, such as temperature, agitation, and the enzyme/acid ratio were held constant. The kinetics were determined by assessing the acetic acid concentration throughout the reactive process. Experimental data were correlated with the rate equation consisting of a modified version of the Bi–Bi Ping-Pong mechanism. The results showed that when no hydrophobic solvents were used with the reagents in stoichiometric proportion, a high molar fraction of acetic acid (x_0,acid ≈ 0.50) caused the loss of enzymatic activity, achieving a conversion of only 5%. However, when there was an excess of pentan-1-ol, the reaction occurred successfully. Under optimal conditions (solvent-free conditions, x_0,alcohol/x_0,acid = 2, and x_0,acid = 0.33), it was found that the enzyme could be reused up to 10 times without a loss of activity, reaching conversions higher than 80% after 8 h. Therefore, those conditions are advantageous in terms of productivity.

A numerical application has been carried out to determine the thermophysical properties of more than fifty pure liquid compounds involved in the production process of cyclohexanone, whose real values are unknown, in many cases. Two group-contribution methods, the Joback and the Marrero–Gani methods, both used in the fields of physicochemistry and engineering, are employed. Both methods were implemented to evaluate critical properties, phase transition properties, and others, which are required for their use in industrial process simulation/design. The quality of the estimates is evaluated by comparing them with those from the literature, where available. In general, both models provide acceptable predictions, although each of them shows improvement for some of the properties considered, recommending their use, when required.

Thermodynamics, as a scientific tool, advises on the control of variables involved in processes of different nature and is particularly useful in the design of equipment, or to obtain previous simulations. However, to generate more accurate models, an exact science is required. Thus, the thermodynamic–mathematical binomial is able to relate the fundamental variables of a system using the potential functions directing the process, although these relationships are not always completely satisfactory, as it is necessary to complete the modelling with a set of parameters, which depend on the experimentation. To ensure a better description of the behavior of a system, in this work a multi-objective optimization procedure (MOP) is applied to the NRTL model, comparing the results with other conventional procedures used to characterize the real properties of the binary methyl methanoate + pentane. The results obtained with the MOP confirmed a better representation of the experimental information with NRTL, analyzing its impact on the simulation/design processes. The set of optimal parametrizations obtained allow several options to be process engineered to select the most appropriate one depending on the specific problem to be designed.

In an attempt to evaluate the separation of certain impurities that arise in some stages of the production of cyclohexanone, this work analyzed the possibility of removing five of these substances via rectification. Due to the scarcity of experimental vapor–liquid equilibrium data for most of the solutions in the effluent of the global process, prior knowledge of their behavior is required. In this work, two predictive models, UNIFAC and COSMO-RS, were used to determine a priori the possibility of obtaining, by distillation, the individual components of seven of the binaries formed by the combination of these five compounds. Since both procedures described quasi-ideal behavior for all the chosen solutions, the results are considered as an approximation, owing to the special nature of the studied systems. The results and characteristics of each system are discussed separately.

This work provides density data (~1300 values) of 14 alcohols with up to five carbon atoms at p ∈ [0.1–40] MPa and T ∈ [278–358] K. The information obtained is modeled with a convenient reformulation of the Tait equation from which the volumetric coefficients, α and β, are derived both analytically and numerically. The general EoS containing α and β is also used for checking the consistency of the hypothesis on the invariability of the cited thermophysic parameters. The results obtained can be considered reliable because of the low estimated errors between the experimental data and those of the literature, which are below 0.4% for volume, while for the volumetric coefficients there is always a reference diverging 10%, or less, from the proposed model estimations. By including the averages of α and β into the general state of equation the errors increase, being <15%, compared to those based on the Tait equation. Hence, the assumption on the stability of the volumetric coefficients in this working interval is sufficient to make rough estimations of the molar volume of the selected alcohols.