LZLi Zhang

Li Zhang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Li Zhang has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Modeling Investigation on Gas Backflow Performances in Screw Vacuum Pump

    by Li Zhang, Yang Liu, Yongju Zhang, Xue Liu, Wenfei Liu, Ziyun Chen

    Rotor structure has a great influence on the gas backflow in a screw vacuum pump. The characteristics of the gas main flow along the spiral groove of the screw rotor and the gas reverse flow along the tooth-shaped, tooth side, radial, and circumferential clearances are investigated. A new mathematical model of the pumping flow and backflow involved in a flow balance model is proposed to investigate the actions of the shearing force and pressure difference force. The calculated backflow is verified by comparing the experimental measured results. The relationships of the structural parameters of the screw rotor are established. The effects of the rotor parameters, such as pitch, diameter, and compression ratio, on backflow are revealed. The results show that the rotor diameter and compression ratio remain constant and that the influence of pitch on the backflow is slightly weak, with backflow variations of less than 3%, whereas the pitch, rotor length, and compression ratio are constant and the rotor addendum diameter is directly proportional to the backflow. The addendum diameter of rotor #4 is the largest, and its backflow is about 1.5 times larger than that of rotor #1. When the rotor radial sizes and the pitch of the suction end are constant, the compression ratio is inversely proportional to the backflow in the low-pressure region and proportional to the backflow in the high-pressure regions. Therefore, for a vacuum pump operating in low-pressure areas, the use of the compression ratio of 2.2 or higher is favorable for the reduction in backflow.


  • Open Access

    Correlation Research between Asymmetry Coefficient of Gondola Car Body and Stress Distribution of Cross Bearer Weld

    by Wenfei Liu, Li Zhang, Chen Bi, Zhixiong Gao, Xiongtao Pu

    In order to find out the root cause of cross bearer welds’ cracks in general-purpose gondola cars, the relationship between asymmetric structure and stress distribution is studied in this paper. Firstly, the concept of asymmetry coefficient and stress distribution cluster is proposed, and the asymmetric coefficients’ calculation methods of independent and dependent variables are given, respectively, in two-dimensional space. Secondly, according to the different positions of side column 1 and side column 2, 30 local models are established, the cross bearer weld stresses are extracted after finite element simulation, and the stress distribution clusters of cross bearer weld stresses are formed. Finally, the asymmetry coefficients of the side columns are calculated, and the correlation between the positions of the side columns and the weld stresses is studied using the methods of Pearson correlation coefficient and complex correlation coefficient. The results show that the correlation between the stress of cross bearer weld 2 and the positions of the side columns is much higher than that between the stress of cross bearer weld 1 and the positions of the side columns. Meanwhile, it shows that the method presented in this paper is feasible and effective for the analysis and research of asymmetric structures. These combined with the calculation method of the correlation coefficient.


  • Open Access

    An Improved Metamorphosis-Based Scheme of Feed Mechanism Using Configuration Synthesis

    by Li Zhang, Yang Liu, Yongju Zhang

    In this work, the principle of metamorphic mechanism is optimized for the product design based on variable topological structures. One metamorphic element consisting of kinematic pair and kinematic size is proposed firstly and a configuration synthesis strategy for feed mechanism is performed in term of the translocation, inversion and duplication variation methods. Metamorphic elements are obtained by decomposing the source metamorphic mechanism. A novelty configuration scheme based on constraint variation features is established by the solution of the constraint relationship of metamorphic elements, and three kinds of configurations are synthesized. Comparisons with kinematic performances between source mechanism and developed mechanism configurations are modelled by the kinematic simulation. Results demonstrate that the multiple types of metamorphic mechanisms can be successfully synthesized, and the demands of functional targets are satisfied completely.


  • Open Access

    An improved metamorphosis-based scheme of configuration synthesis for feed mechanism

    by Li Zhang, Yang Liu, Yongju Zhang

    In this work, the principle of metamorphic mechanism is optimized for product design based on the variable topological structures. A metamorphic element consisting of kinematic pair and kinematic size is proposed firstly. A new configuration synthesis strategy for feed mechanism is performed in view of the translocation, inversion and duplication variation methods. The metamorphic elements are obtained by means of the decomposing the source metamorphic mechanism. A novelty configuration scheme based on constraint variation features is established by the solution of constraint relationship of metamorphic elements, and three kinds of configurations are synthesized. The comparisons of kinematic performances between source mechanism and new mechanism configurations are carried out using kinematic simulation. Results demonstrate that proposed strategy can synthesize successfully multiple types of the metamorphic mechanisms to meet the demands of functional targets.


  • Open Access

    A novel design on smooth rotor profile with meshing clearance for screw vacuum pump

    by Li Zhang, Yang Liu, Yongju Zhang, Ziyun Chen

    Cross-section profile of rotor takes a great effect on the performance of dry-screw vacuum pump. A novel smooth rotor profile consisting of eight segments of curves, including arcs and conjugate correction curves is proposed. Advantages are that it can be used to solve the unsmooth connection and no meshing clearance in traditional profile. The meshing model for new profile can directly generate stable addendum clearance, tooth clearance, tooth side clearance, and radial clearance. The influences of the epicycloid rotation angle, arc radius and involute offset distance of the conjugate correction curve on the clearances are studied according to established theoretical model. And transient flow field of vacuum pump is analyzed by using the commercial software Ansys-Fluent®. Compared to traditional screw vacuum pump, the results shows that pressure in inlet and pump cavity is lower, and maximum pumping speed is higher, indicating that the proposed design is superior.


  • Open Access

    Effects of stable clearances on backflow in the variable-pitch screw vacuum pump

    by Li Zhang, Yongju Zhang, Ziyun Chen

    Effects of various clearances of variable-pitch screw vacuum pump on gas backflow of internal flow field of the pump cavity is studied. The theoretical tooth surfaces of screw rotor are optimized by radial, normal equidistance modifications, and four types of stable clearances of rotor circumferential, radial, tooth shape and tooth sides are obtained. The backflow calculation model in clearances considering Couette backflow and orifice backflow is improved. The three-dimensional model of variable-pitch screw vacuum pump is designed, and the experimental prototype and test device are developed. The internal backflow of vacuum pump is analyzed by using the commercial software Ansys-Fluent® and the calculation model. The results show that the smaller the clearances, the smaller the backflow and the higher the vacuum degree. Among the four types of clearances, the circumferential clearance plays the primary roles. The backflow is directly proportional to the inlet pressure and rotating speed. Predictions are validated by the experimental data with satisfied agreement.