Heba Nassar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Heba Nassar has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Hikmat Said Hilal
Department of Chemistry, An-Najah National University, Nablus, Palestine
8 shared publications - Tae Woo Kim
Korea Institute of Energy Research
4 shared publications - Allan Daraghmeh
Department of Physics, An-Najah National University, Nablus, Palestine
3 shared publications - Hyobin Han
Hydrogen Research Department, Korea Institute of Energy Research, 152, Gajeong-ro, Yuseong-gu, Daejeon 34129, Republic of Korea
3 shared publications - Mohyeddin Assali
Department of Pharmaceutical Chemistry and Technology, Faculty of Pharmacy, An-Najah National University, Nablus, Palestine
3 shared publications - Abdelrahim Abusafa
Department of Chemical Engineering, Faculty of Engineering and Information Technology, An-Najah National University, Nablus P400, Palestine
2 shared publications
Latest Publications
- 30 January 2026
- Published by Springer Nature in Chemical Papers
- Vol. 80 (4) , 3641-3659
Assessment of Dead Sea water as a natural electrolyte in supercapacitors
- 30 January 2026
- Published by Springer Nature in Chemical Papers
- Vol. 80 (4) , 3641-3659
Assessment of Dead Sea water as a natural electrolyte in supercapacitors
- Open Access
Coffee-Waste-Based ZnCl2 Activated Carbon in High-Performance Supercapacitor Electrodes: Impact of Graphitization, Surface Morphology, Porosity and Conductivity
Activated carbon (AC) electrodes from coffee waste (CW) were earlier assessed in supercapacitors but showed lower supercapacitor performance in terms of specific capacity (Cs), specific power (Ps) or both, compared to other biowastes. This work describes how CW-based AC electrode performance may be improved if carefully prepared. Careful processing yields higher graphitization, carbon content (aromaticity), conductivity and porosity free of any residues. Thus, AC electrodes will exhibit higher Cs and Ps simultaneously. CW was first pyrolyzed (CPyrol) and then chemically activated by ZnCl2 (ACChem). Both materials were characterized using SEM, TEM, BET, FT-IR spectra, Raman spectra and XRD. The ACChem exhibited much higher graphitization, crystallinity, specific surface area (SSA), porosity and conductivity. From cyclic voltammetry, the ACChem electrode exhibited a Cs of 261 F/g, an energy density of 18.3 Wh/kg and a Ps of 360 W/kg at 0.33 A/g. From galvanostatic charge–discharge, there was a stable Cs of 150 F/g at 0.33 A/g over 5000 charge–discharge cycles. From electrochemical impedance spectroscopy, the Cs was ~180 F/g, with a low equivalent series resistance (ESR) of 0.56 Ω at a frequency of 0.01 Hz, compared to the literature. The ACChem electrode was superior to the CPyrol electrode and to earlier CW-based AC counterparts, with much lower resistance. Moreover, the electrode competed with other biowaste-based electrodes.
Open AccessCoffee-Waste-Based ZnCl2 Activated Carbon in High-Performance Supercapacitor Electrodes: Impact of Graphitization, Surface Morphology, Porosity and Conductivity
Activated carbon (AC) electrodes from coffee waste (CW) were earlier assessed in supercapacitors but showed lower supercapacitor performance in terms of specific capacity (Cs), specific power (Ps) or both, compared to other biowastes. This work describes how CW-based AC electrode performance may be improved if carefully prepared. Careful processing yields higher graphitization, carbon content (aromaticity), conductivity and porosity free of any residues. Thus, AC electrodes will exhibit higher Cs and Ps simultaneously. CW was first pyrolyzed (CPyrol) and then chemically activated by ZnCl2 (ACChem). Both materials were characterized using SEM, TEM, BET, FT-IR spectra, Raman spectra and XRD. The ACChem exhibited much higher graphitization, crystallinity, specific surface area (SSA), porosity and conductivity. From cyclic voltammetry, the ACChem electrode exhibited a Cs of 261 F/g, an energy density of 18.3 Wh/kg and a Ps of 360 W/kg at 0.33 A/g. From galvanostatic charge–discharge, there was a stable Cs of 150 F/g at 0.33 A/g over 5000 charge–discharge cycles. From electrochemical impedance spectroscopy, the Cs was ~180 F/g, with a low equivalent series resistance (ESR) of 0.56 Ω at a frequency of 0.01 Hz, compared to the literature. The ACChem electrode was superior to the CPyrol electrode and to earlier CW-based AC counterparts, with much lower resistance. Moreover, the electrode competed with other biowaste-based electrodes.
- Open Access
- 11 October 2024
- Published by MDPI AG in Preprints.org
Physically and Chemically Activated Carbon from Coffee Waste in High Performance Supercapacitor Electrodes
Biowaste sources, like coffee wastes (CWs), are considered for advanced materials. CW was assessed to prepare activated carbon for supercapacitor electrodes, but showed low performance compared to other counterparts. Enhanced CW activation process may help address this limitation. In this study, CW was subjected to two activation methods: physical (pyrolysis) activation and physical-chemical activation using ZnCl2, to determine the more effective approach. Both resulting materials were analyzed using SEM, TEM, BET, Raman spectroscopy and XRD. The physical-chemical activation yielded activated carbon with better characteristics, including a higher specific-surface area (SSA) of ~830 m²/g, compared to 458 m²/g from the physical activation. With its promising potential for supercapacitor electrodes, the former activated carbon was singled out for supercapacitor study. Cyclic voltammetry revealed a specific capacitance of 261 F g-1, and energy density of 18.3 Wh/kg, with power density of 360 W/kg at a current density 0.33 A/g. Charge-discharge studies showed a specific capacitance of 150 F g-1 at the same current density. Electrochemical impedance spectroscopy indicated a specific capacitance of 180 F g-1, with an equivalent series resistance of 0.56 Ω at a low frequency of 0.01 Hz. The electrode exhibited exceptional characteristics, maintaining high stability over 5,000 charge-discharge cycles.
- 11 October 2024
- Published by MDPI AG in Preprints.org
Open AccessPhysically and Chemically Activated Carbon from Coffee Waste in High Performance Supercapacitor Electrodes
Biowaste sources, like coffee wastes (CWs), are considered for advanced materials. CW was assessed to prepare activated carbon for supercapacitor electrodes, but showed low performance compared to other counterparts. Enhanced CW activation process may help address this limitation. In this study, CW was subjected to two activation methods: physical (pyrolysis) activation and physical-chemical activation using ZnCl2, to determine the more effective approach. Both resulting materials were analyzed using SEM, TEM, BET, Raman spectroscopy and XRD. The physical-chemical activation yielded activated carbon with better characteristics, including a higher specific-surface area (SSA) of ~830 m²/g, compared to 458 m²/g from the physical activation. With its promising potential for supercapacitor electrodes, the former activated carbon was singled out for supercapacitor study. Cyclic voltammetry revealed a specific capacitance of 261 F g-1, and energy density of 18.3 Wh/kg, with power density of 360 W/kg at a current density 0.33 A/g. Charge-discharge studies showed a specific capacitance of 150 F g-1 at the same current density. Electrochemical impedance spectroscopy indicated a specific capacitance of 180 F g-1, with an equivalent series resistance of 0.56 Ω at a low frequency of 0.01 Hz. The electrode exhibited exceptional characteristics, maintaining high stability over 5,000 charge-discharge cycles.
- Open Access
Electro-Mineralization of Aqueous Phenazopyridine Using Platinum Nanoparticles Deposited onto Multiwalled Carbon Nanotubes
Water may easily become polluted by pharmaceutical wastes, such as phenazopyridine hydrochloride. The pollutant can be removed by electrochemical oxidation in the form of minerals. A novel electrode has been developed for this purpose. Pt nanoparticles (PtNPs) are electrodeposited onto multiwalled carbon nanotubes supported onto fluorine-doped tin oxide (FTO/Glass). The resulting PtNP@MWCNT-FTO-E electrode is characterized by X-ray diffraction, atomic force microscopy, scanning electron microscopy, electron diffraction spectroscopy and X-ray photoelectron spectroscopy. The electrode exhibits high efficiency in the electrochemical oxidation process thanks to the large specific surface area of the PtNPs and their ability to behave as charge transfer catalysts. The contaminant undergoes complete mineralization, leaving no organics after treatment. The resulting nitrate ions further confirm contaminant mineralization, but fortunately, they disappear over time, which confirms the safety of the process in water treatment. Moreover, the electrode operates under a variety of applied potentials, pH values, temperatures and contaminant concentrations. The electrode exhibits high stability upon recovery and reuse while retaining its physical characteristics before and after use. This study highlights the benefit of using Pt nanoparticles in the electro-degradation of aqueous organic contaminants, especially waste pharmaceuticals, for the first time. It also recommends scaling up the process and studying the continuous-flow reaction process to assess the economic and technical feasibility in future large-scale applications.
Open AccessElectro-Mineralization of Aqueous Phenazopyridine Using Platinum Nanoparticles Deposited onto Multiwalled Carbon Nanotubes
Water may easily become polluted by pharmaceutical wastes, such as phenazopyridine hydrochloride. The pollutant can be removed by electrochemical oxidation in the form of minerals. A novel electrode has been developed for this purpose. Pt nanoparticles (PtNPs) are electrodeposited onto multiwalled carbon nanotubes supported onto fluorine-doped tin oxide (FTO/Glass). The resulting PtNP@MWCNT-FTO-E electrode is characterized by X-ray diffraction, atomic force microscopy, scanning electron microscopy, electron diffraction spectroscopy and X-ray photoelectron spectroscopy. The electrode exhibits high efficiency in the electrochemical oxidation process thanks to the large specific surface area of the PtNPs and their ability to behave as charge transfer catalysts. The contaminant undergoes complete mineralization, leaving no organics after treatment. The resulting nitrate ions further confirm contaminant mineralization, but fortunately, they disappear over time, which confirms the safety of the process in water treatment. Moreover, the electrode operates under a variety of applied potentials, pH values, temperatures and contaminant concentrations. The electrode exhibits high stability upon recovery and reuse while retaining its physical characteristics before and after use. This study highlights the benefit of using Pt nanoparticles in the electro-degradation of aqueous organic contaminants, especially waste pharmaceuticals, for the first time. It also recommends scaling up the process and studying the continuous-flow reaction process to assess the economic and technical feasibility in future large-scale applications.
- Open Access
Why Carbon Nanotubes Improve Aqueous Nanofluid Thermal Conductivity: A Qualitative Model Critical Review
Media thermal conductivity is important in various heat-transfer processes. Many conventional fluid conductors suffered low conductivity and environmental issues. Therefore, research was active in finding out alternative systems, mostly relying on aqueous liquids that are low-cost and ecofriendly. After the emergence of carbon nanotubes (CNTs), with their many special structural, electrical and thermal properties, they have been examined for many applications, including heat-transfer processes. Adding CNTs to water yields CNT aqueous nanofluids that have been widely investigated as heat-transfer media. The literature shows that CNT addition improves water thermal conductivity and other water properties, such as viscosity, surface tension, freezing point and boiling point. The literature also shows that nanofluid thermal conductivity improvement is affected by CNT type and concentration, in addition to other factors such as surfactant addition. All these subjects were widely described in literature, focusing on experimental, modelling and theoretical accounts. Despite the wide literature, there exist inconsistencies and discrepancies between reports that need to be justified. In addition to technical papers, many reviews were published on various aspects of the subject including experimental results and mathematical modeling. However, the very basic question here is as follows: Why does adding CNT to water affect its thermal conductivity? In spite of the wide published literature, this issue was not targeted in a simple qualitative approach. This review provides a clear understanding of how CNTs improve thermal conductivity of aqueous nanofluids. A qualitative model is presented to explain mechanisms behind improvement as presented in the literature. CNT type effects are discussed with other factors such as aspect ratio, Reynold number, dispersion quality, composition, temperature and additives. CNT functionalization is described. Relations to estimate nanofluid thermal conductivity are discussed. The model will help specialists to tailor CNT aqueous nanofluid characteristics as desired by varying types and concentrations of CNT and surfactant, and other factors.
Open AccessWhy Carbon Nanotubes Improve Aqueous Nanofluid Thermal Conductivity: A Qualitative Model Critical Review
Media thermal conductivity is important in various heat-transfer processes. Many conventional fluid conductors suffered low conductivity and environmental issues. Therefore, research was active in finding out alternative systems, mostly relying on aqueous liquids that are low-cost and ecofriendly. After the emergence of carbon nanotubes (CNTs), with their many special structural, electrical and thermal properties, they have been examined for many applications, including heat-transfer processes. Adding CNTs to water yields CNT aqueous nanofluids that have been widely investigated as heat-transfer media. The literature shows that CNT addition improves water thermal conductivity and other water properties, such as viscosity, surface tension, freezing point and boiling point. The literature also shows that nanofluid thermal conductivity improvement is affected by CNT type and concentration, in addition to other factors such as surfactant addition. All these subjects were widely described in literature, focusing on experimental, modelling and theoretical accounts. Despite the wide literature, there exist inconsistencies and discrepancies between reports that need to be justified. In addition to technical papers, many reviews were published on various aspects of the subject including experimental results and mathematical modeling. However, the very basic question here is as follows: Why does adding CNT to water affect its thermal conductivity? In spite of the wide published literature, this issue was not targeted in a simple qualitative approach. This review provides a clear understanding of how CNTs improve thermal conductivity of aqueous nanofluids. A qualitative model is presented to explain mechanisms behind improvement as presented in the literature. CNT type effects are discussed with other factors such as aspect ratio, Reynold number, dispersion quality, composition, temperature and additives. CNT functionalization is described. Relations to estimate nanofluid thermal conductivity are discussed. The model will help specialists to tailor CNT aqueous nanofluid characteristics as desired by varying types and concentrations of CNT and surfactant, and other factors.
- Open Access
- 29 March 2024
- Published by MDPI AG in Preprints.org
Why Carbon Nanotubes Improve Aqueous Nanofluid Thermal Conductivity: A Qualitative Model
Media thermal conductivity is important in various heat-transfer processes. Many conventional fluid conductors suffered low conductivity and environmental issues. Therefore, researchers developed efficient aqueous nanofluid conductors. Carbon nanotubes (CNTs) are widely studied to reach efficient, stable, low-cost and environmentally-friendly aqueous-nanofluids. This review provides a clear understanding of how CNTs improve thermal conductivity of aqueous nanofluids. A qualitative model is presented to explain literature mechanisms behind improvement. CNT type effects are discussed with other factors such as aspect ratio, Reynold number, dispersion quality, composition, temperature and additives. CNT functionalization is described. Relations to estimate nanofluid thermal conductivity are discussed. The model will help specialists to tailor CNT aqueous nanofluids as desired.
- 29 March 2024
- Published by MDPI AG in Preprints.org
Open AccessWhy Carbon Nanotubes Improve Aqueous Nanofluid Thermal Conductivity: A Qualitative Model
Media thermal conductivity is important in various heat-transfer processes. Many conventional fluid conductors suffered low conductivity and environmental issues. Therefore, researchers developed efficient aqueous nanofluid conductors. Carbon nanotubes (CNTs) are widely studied to reach efficient, stable, low-cost and environmentally-friendly aqueous-nanofluids. This review provides a clear understanding of how CNTs improve thermal conductivity of aqueous nanofluids. A qualitative model is presented to explain literature mechanisms behind improvement. CNT type effects are discussed with other factors such as aspect ratio, Reynold number, dispersion quality, composition, temperature and additives. CNT functionalization is described. Relations to estimate nanofluid thermal conductivity are discussed. The model will help specialists to tailor CNT aqueous nanofluids as desired.
- Open Access
Perovskite Nano-Powder and Nano-Film Catalysts in Mineralization of Aqueous Organic Contaminants through Solar Simulated Radiation
Water contamination with various contaminants, including organic species, is a global concern. Reclamation through safe, economic and technically feasible methods is imperative. Two perovskites, zinc titanate (ZnTiO3) and manganese titanate (MnTiO3), mixed with TiO2 phases, were prepared as nano-powders and nano-films. The materials were characterized and used as catalysts in photodegradation of aqueous methylene blue, a hazardous model contaminant, using solar simulated radiation. The effects of various reaction conditions on the photodegradation were examined. The kinetics indicated the suitability of using the process at various contaminant concentrations and catalyst loadings. Both powder and film catalysts completely removed the contaminant in less than 6 h. Powder and film forms of the MnTiO3 mixture were more efficient than their ZnTiO3 counterparts. In both perovskite mixtures, the films exhibited higher catalytic efficiency than the powders. The film materials exhibited high catalytic efficiency in both the continuous flow and batch processes. Water contaminated with various methylene blue concentrations can be treated by the film catalysts that can be recovered and reused with no technical difficulties. The results open new horizons for larger-scale water purification processes.
Open AccessPerovskite Nano-Powder and Nano-Film Catalysts in Mineralization of Aqueous Organic Contaminants through Solar Simulated Radiation
Water contamination with various contaminants, including organic species, is a global concern. Reclamation through safe, economic and technically feasible methods is imperative. Two perovskites, zinc titanate (ZnTiO3) and manganese titanate (MnTiO3), mixed with TiO2 phases, were prepared as nano-powders and nano-films. The materials were characterized and used as catalysts in photodegradation of aqueous methylene blue, a hazardous model contaminant, using solar simulated radiation. The effects of various reaction conditions on the photodegradation were examined. The kinetics indicated the suitability of using the process at various contaminant concentrations and catalyst loadings. Both powder and film catalysts completely removed the contaminant in less than 6 h. Powder and film forms of the MnTiO3 mixture were more efficient than their ZnTiO3 counterparts. In both perovskite mixtures, the films exhibited higher catalytic efficiency than the powders. The film materials exhibited high catalytic efficiency in both the continuous flow and batch processes. Water contaminated with various methylene blue concentrations can be treated by the film catalysts that can be recovered and reused with no technical difficulties. The results open new horizons for larger-scale water purification processes.
- 6 January 2022
- Published by Elsevier in Journal of Environmental Management
- Vol. 305, 114420
Effective and selective electroreduction of aqueous nitrate catalyzed by copper particles on multi-walled carbon nanotubes
- 6 January 2022
- Published by Elsevier in Journal of Environmental Management
- Vol. 305, 114420
Effective and selective electroreduction of aqueous nitrate catalyzed by copper particles on multi-walled carbon nanotubes